An official website of the United States government
High sulfur-content materials (HSMs) formed via inverse vulcanization of elemental sulfur with animal fats and/or plant oils can exhibit remarkable mechanical strength and chemical resistance, sometimes superior to commercial building products. Adding pozzolan fine materials—fly ash (FA), silica fume (SF), ground granulated blast furnace slag (GGBFS), or metakaolin (MK)—can further improve HSM mechanical properties and stability. Herein, we detail nine materials comprised of rancidified chicken fat, elemental sulfur, and canola or sunflower oil (to yield CFS or GFS, respectively) and, with or without FA, SF, GGBFS, or MK. The base HSMs, CFS90 or GFS90, contained 90 wt% sulfur, 5 wt% chicken fat, and 5 wt% canola or sunflower oil, respectively. For each HSM/fine combination, the resulting material was prepared using a 95:5 mass input ratio of HSM/fine. No material exhibited water uptake >0.2 wt% after immersion in water for 24 h, significantly lower than the 28 wt% observed with ordinary Portland cement (OPC). Impressively, CFS90, GFS90, and all HSM/fine combinations exhibited compressive strength values 15% to 55% greater than OPC. After immersion in 0.5 M H2SO4, CFS90, GFS90, and its derivatives retained 90% to 171% of the initial strength of OPC, whereas OPC disintegrated under these conditions. CFS90, GFS90, and its derivatives collectively show promise as sustainable materials and materials with superior performance versus concrete.
more »
« less
Thermal and Mechanical Properties of Recyclable Composites Prepared from Bio-Olefins and Industrial Waste
Ordinary Portland Cement (OPC) production consumes tremendous amounts of fresh water and energy and releases vast quantities of CO2 into the atmosphere. Not only would an alternative to OPC whose production requires no water, releases little CO2, and consumes less energy represent a transformative advance in the pursuit of industrial decarbonization, but the greater availability of safe drinking water would lead to significantly improved public health, particularly among vulnerable populations most at risk from contaminated water supply. For any OPC alternative to be adopted on any meaningful scale, however, its structural capabilities must meet or exceed those of OPC. An inverse vulcanization of brown grease, sunflower oil, and elemental sulfur (5:5:90 weight ratio) was successfully modified to afford the high-sulfur-content material SunBG90 in quantities > 1 kg, as was necessary for standardized ASTM and ISO testing. Water absorption (ASTM C140) and thermal conductivity (ISO 8302) values for SunBG90 (<1 wt% and 0.126 W·m−1·K−1, respectively) were 84% and 94% lower than those for OPC, respectively, suggesting that SunBG90 would be more resistant against freeze-thaw and thermal stress damage than OPC. Consequently, not only does SunBG90 represent a more environmentally friendly material than OPC, but its superior thermomechanical properties suggest that it could be a more environmentally robust material on its own merits, particularly for outdoor structural applications involving significant exposure to water and seasonal or day/night temperature swings.
more »
« less
- Award ID(s):
- 2203669
- PAR ID:
- 10434788
- Date Published:
- Journal Name:
- Journal of Composites Science
- Volume:
- 7
- Issue:
- 6
- ISSN:
- 2504-477X
- Page Range / eLocation ID:
- 248
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
The unique properties and sustainability advantages of sulfur polymer cement have led to efforts to use them as alternatives to traditional Portland cement. The current study explores the impact of environmental stresses on the strength development of polymer composite SunBG90, a material composed of animal and plant fats/oils vulcanized with 90 wt. % sulfur. The environmental stresses investigated include low temperature (−25 °C), high temperature (40 °C), and submersion in water, hexanes, or aqueous solutions containing strong electrolyte, strong acid, or strong base. Samples were analyzed for the extent to which exposure to these stresses influenced the thermo-morphological properties and the compressional strength of the materials compared to identical materials allowed to develop strength at room temperature. Differential scanning calorimetry (DSC) analysis revealed distinct thermos-morphological transitions in stressed samples and the notable formation of metastable γ-sulfur in hexane-exposed specimens. Powder X-ray diffraction confirmed that the crystalline domains identified by DSC were primarily γ-sulfur, with ~5% contribution of γ-sulfur in hexane-exposed samples. Compressive strength testing revealed high strength retention other than aging at elevated temperatures, which led to ~50% loss of strength. These findings reveal influences on the strength development of SunBG90, lending important insight into possible use as an alternative to OPC.more » « less
-
There are ongoing research efforts directed at addressing strength limitations of compressed earth blocks (CEB) that inhibit their deployment for structural applications, particularly in areas where masonry systems are regularly subjected to lateral loads from high winds. In this paper, the authors focus specifically on the extent to which polypropylene (PP) fibers can be used to enhance the flexural performance of CEB. Cementitious matrices used for CEB production exhibit low tensile and flexural strength (brittle) properties. This work investigates plain (unreinforced) and fiber-reinforced specimens (short flexural beams) with fiber mass content of 0.2, 0.4, 0.6, 0.8, and 1.0% and ordinary Portland cement (OPC) content of 8%. The influence of the inclusion of fiber was based on tests conducted using the Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (ASTM C1609). Material properties that were quantified included first-peak strength, peak strength, equivalent flexural strength, residual strength, and flexural toughness. There was an observed improvement in the performance of the soil-fiber matrixes based on these results of these tests. It was also observed that when the fiber content exceeded 0.6% and above, specimens exhibited a deflection- hardening behavior; an indication of improvement in ductility. An equivalent flexural strength predictive model is proposed.more » « less
-
Abstract Rancid animal fats unsuitable for human or animal food production represent low‐value and abundant, yet underexploited organic chemical precursors. The current work describes a strategy to synthesize high sulfur‐content materials (HSMs) that directly utilizes a blend of partially hydrolyzed chicken fat and plant oils as the organic comonomers, following up on analogous reactions using brown grease in place of chicken fat. The reaction of sulfur and chicken fat with either canola or sunflower oil yielded crosslinked polymer composites CFSxor GFSx, respectively (x = wt% sulfur, varied from 85%–90%). The composites exhibited compressive strengths of 24.7–31.7 MPa, and flexural strengths of 4.1–5.7 MPa, exceeding the value of established construction materials like ordinary Portland cement (compressive strength ≥17 MPa required for residential building, flexural strength 2–5 MPa). The composites also exhibited thermal stability up to 215–224 °C. The simple single‐step protocol described herein represents a way to upcycle an affordable and previously unexploited animal fat resource to form structural composites via the atom economical inverse vulcanization mechanism.more » « less
-
Rusănescu, C; Ungureanu, N (Ed.)Excessive land application of poultry litter (PL) may lead to surface runoff of nitrogen (N) and phosphorus (P), which cause eutrophication, fish death, and water pollution that ultimately have negative effects on humans and animals. Increases in poultry production in the Delmarva Peninsula underscore the need for more efficient, cost-effective, and sustainable disposal technologies for processing PL instead of direct land application. The pyrolysis conversion process can potentially produce nutrient-rich poultry litter biochar (PLB), while the pyrolysis process can change the N and P to a more stable component, thus reducing its runoff. Pyrolysis also kills off any microorganisms that would otherwise trigger negative environmental health effects. This study is to apply an integrated method and investigate the effect of pyrolysis temperature (300 °C, 500 °C), poultry litter source (different feedstock composition), and bedding material mixture (10% pine shavings) on PLB qualities and quantities. Proximate and ultimate analysis showed PL sources and bedding material addition influenced the physicochemical properties of feedstock. The SEM and BET surface results indicate that pyrolysis temperature had a significant effect on changing the PLB morphology and structure, as well as the pH value (7.78 at 300 °C vs. 8.78 at 500 °C), extractable phosphorus (P) (18.73 ppm at 300 °C vs. 11.72 ppm at 500 °C), sulfur (S) (363 ppm at 300 °C vs. 344 ppm at 500 °C), and production yield of PLBs (47.65% at 300 °C vs. 60.62% at 500 °C). The results further suggest that adding a bedding material mixture (10% pine shavings) to PLs improved qualities by reducing the content of extractable P and S, as well as pH values of PLBs. This study also found the increment in both the pore volume and the area of Bethel Farm was higher than that of Sun Farm. Characterization and investigation of qualities and quantities of PLB using the integrated framework suggest that PL from Bethel Farm could produce better-quality PLB at a higher pyrolysis temperature and bedding material mixture to control N and P runoff problems.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.3390/jcs7060248
