An official website of the United States government
Abstract Nanotwinned materials have been widely studied as a promising class of nanostructured materials that exhibit an exceptional combination of high strength, good ductility, large fracture toughness, remarkable fatigue resistance, and creep stability. Recently, an apparent controversy has emerged with respect to how the strength of nanotwinned materials varies as the twin thickness is reduced. While a transition from hardening to softening was observed in nanotwinned Cu when the twin thickness is reduced below a critical value, continuous hardening was reported in nanotwinned ceramics and nanotwinned diamond. Here, by conducting atomistic simulations and developing a theoretical modeling of nanotwinned Pd and Cu systems, we discovered that there exists a softening temperature, below which the material hardens continuously as the twin thickness is reduced (as in nanotwinned ceramics and diamond), while above which the strength first increases and then decreases, exhibiting a maximum strength and a hardening to softening transition at a critical twin thickness (as in nanotwinned Cu). This important phenomenon has been attributed to a transition from source- to stress-controlled plasticity below the softening temperature, and suggests that different hardening behaviors may exist even in the same nanotwinned material depending on the temperature and that at a given temperature, different materials could exhibit different hardening behaviors depending on their softening temperature.
more »
« less
The essential work of fracture in peridynamics
Abstract In this work, the essential work of fracture (EWF) method is introduced for a peridynamic (PD) material model to characterize fracture toughness of ductile materials. First, an analytical derivation for the path-independence of the PD J -integral is provided. Thereafter, the classical J -integral and PD J -integral are computed on a number of analytical crack problems, for subsequent investigation on how it performs under large scale yielding of thin sheets. To represent a highly nonlinear elastic behavior, a new adaptive bond stiffness calibration and a modified bond-damage model with gradual softening are proposed. The model is employed for two different materials: a lower-ductility bainitic-martensitic steel and a higher-ductility bainitic steel. Up to the start of the softening phase, the PD model recovers the experimentally obtained stress–strain response of both materials. Due to the high failure sensitivity on the presence of defects for the lower-ductility material, the PD model could not recover the experimentally obtained EWF values. For the higher-ductility bainitic material, the PD model was able to match very well the experimentally obtained EWF values. Moreover, the J -integral value obtained from the PD model, at the absolute maximum specimen load, matched the corresponding EWF value.
more »
« less
- Award ID(s):
- 1953346
- PAR ID:
- 10435276
- Date Published:
- Journal Name:
- International Journal of Fracture
- Volume:
- 242
- Issue:
- 2
- ISSN:
- 0376-9429
- Page Range / eLocation ID:
- 129 to 152
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
The inclusion-based boundary element method (iBEM) is developed to calculate the elastic fields of a bi-layered composite with inhomogeneities in one layer. The bi-material Green’s function has been applied to obtain the elastic field caused by the domain integral of the source fields on inclusions and the boundary integral of the applied loads on the surface. Using Eshelby’s equivalent inclusion method (EIM), the material mismatch between the particle and matrix phases is simulated with a continuously distributed source field, namely eigenstrain, on inhomogeneities so that the iBEM can calculate the local field. The stress singularity along the interface leads to the delamination of the bimaterials under a certain load. The crack’s energy release rate ( J) is obtained through the J-integral, which predicts the stability of the delamination. When the stiffness of one layer increases, the J-integral increases with a higher gradient, leading to lower stability. Particularly, the effect of the boundary and inhomogeneity on the J-integral is illustrated by changing the crack length and inhomogeneity configuration, which shows the crack is stable at the beginning stage and becomes unstable when the crack tip approaches the boundary; a stiffer inhomogeneity in the neighborhood of a crack tip decreasesJand improves the fracture resistance. For the stable cracking phase, the J-integral increases with the volume fraction of inhomogeneity are evaluated. The model is applied to a dual-glass solar module with air bubbles in the encapsulant layer. The stress distribution is evaluated with the iBEM, and the J-integral is evaluated to predict the delamination process with the energy release rate, which shows that the bubbles significantly increase the J-integral. The effect of the bubble size, location, and number on the J-integral is also investigated. The present method provides a powerful tool for the design and analysis of layered materials and structures.more » « less
-
We studied the compressive-tensile yield asymmetry (CTYA) and its sensitivity to standard post-processing treatments for a 17-4 PH stainless steel processed with selective laser melting (SLM). Quasistatic tensile and compression tests at ambient temperatures reveal a consistent CTYA for all tested conditions, with compressive yield strengths exceeding tensile values. In the as-printed state, yield asymmetry (Δσ) is ∼113 MPa. Stress-relieving at 300 °C results in only a marginal decrease in asymmetry (Δσ ∼109 MPa), suggesting that the residual stresses generated during SLM have a negligible effect on the observed CTYA. Our analyses indicate that “dynamic softening” due to a stress-assisted austenite-to-martensite transformation governs the yield behavior similar to that observed in transformation-induced plasticity (TRIP)-assisted steels containing mechanically unstable retained austenite. This interpretation is further supported by the increased asymmetry, Δσ ∼127 MPa, observed in a solution-treated and aged specimen, which has a slightly higher retained austenite volume fraction (24 % vs. 21 %). Direct aging at 482 °C of the as-printed steel with a ferritic microstructure causes severe embrittlement. Brittle fracture occurs under tensile stresses well below the yield strength. This pronounced loss of ductility most likely arises from a strong <001> fiber texture along the build direction developed during SLM, which is known to promote cleavage-type fracture on {001} planes. A solution treatment at 1000 °C for 1 h, austenitizes the microstructure completely, and subsequent quenching produces a predominantly martensitic structure with a much weaker crystallographic texture, which restores a favorable strength-ductility balance after aging.more » « less
-
Additively manufactured metals often contain pores, which limit the strength and ductility of resulting components. In this study, a ductile fracture model was developed to describe the effect of pore size, in terms of absolute and relative metrics, on fracture strain under uniaxial tension. The model approximates lack of fusion (LoF) pores as penny-shaped cracks, and damage accumulation was based on the J-integral and secondary Q parameter. The model was calibrated with Ti-6Al-4V samples with intentionally introduced pores fabricated by laser powder bed fusion (PBF-LB) additive manufacturing (AM) in as-built and heat-treated conditions. The model captures the experimentally observed size effect, where for a given pore area fraction, larger samples fracture at smaller strains. By identifying the critical pore size for a single, isolated pore for either load or displacement-controlled applications, the model developed in this study is a crucial step to developing a comprehensive fracture model for establishing confidence in the structural capability of pore-containing additively manufactured components.more » « less
-
Balancing strength and ductility is crucial for structural materials, yet often presents a paradoxical challenge. This research focuses on crafting a unique bimetallic structure, combining non-magnetic, stainless steel 316L (SS316L) with limited strength but enhanced ductility and magnetic, martensitic 17-4 PH with higher strength but lower ductility. Utilizing a powder-based laser-directed energy deposition (L-DED) system, two vertical bimetallic configurations (SS316L/17-4 PH) and a radial bimetallic structure (SS316L core encased in 17-4 PH) were fabricated. Monolithic SS316L, 17-4 PH, and a 50% SS316L/50% 17-4 PH mixture were printed. The printed samples' phase, microstructure, room temperature mechanical properties, and fracture morphology were examined in as-printed conditions. Bimetallic samples exhibited both phases, with a smooth grain transition at the interface. Radial bimetallic samples demonstrated higher mechanical strength than other compositions, except 17-4 PH. These findings showcase the potential of the L-DED approach for creating functional components with tailored mechanical properties.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1007/s10704-023-00705-y
