An official website of the United States government
SUMMARY Infrasound sensors are deployed in a variety of spatial configurations and scales for geophysical monitoring, including networks of single sensors and networks of multisensor infrasound arrays. Infrasound signal detection strategies exploiting these data commonly make use of intersensor correlation and coherence (array processing, multichannel correlation); network-based tracking of signal features (e.g. reverse time migration); or a combination of these such as backazimuth cross-bearings for multiple arrays. Single-sensor trace-based denoising techniques offer significant potential to improve all of these various infrasound data processing strategies, but have not previously been investigated in detail. Single-sensor denoising represents a pre-processing step that could reduce the effects of ambient infrasound and wind noise in infrasound signal association and location workflows. We systematically investigate the utility of a range of single-sensor denoising methods for infrasound data processing, including noise gating, non-negative matrix factorization, and data-adaptive Wiener filtering. For the data testbed, we use the relatively dense regional infrasound network in Alaska, which records a high rate of volcanic eruptions with signals varying in power, duration, and waveform and spectral character. We primarily use data from the 2016–2017 Bogoslof volcanic eruption, which included multiple explosions, and synthetics. The Bogoslof volcanic sequence provides an opportunity to investigate regional infrasound detection, association, and location for a set of real sources with varying source spectra subject to anisotropic atmospheric propagation and varying noise levels (both incoherent wind noise and coherent ambient infrasound, primarily microbaroms). We illustrate the advantages and disadvantages of the different denoising methods in categories such as event detection, waveform distortion, the need for manual data labelling, and computational cost. For all approaches, denoising generally performs better for signals with higher signal-to-noise ratios and with less spectral and temporal overlap between signals and noise. Microbaroms are the most globally pervasive and repetitive coherent ambient infrasound noise source, with such noise often referred to as clutter or interference. We find that denoising offers significant potential for microbarom clutter reduction. Single-channel denoising of microbaroms prior to standard array processing enhances both the quantity and bandwidth of detectable volcanic events. We find that reduction of incoherent wind noise is more challenging using the denoising methods we investigate; thus, station hardware (wind noise reduction systems) and site selection remain critical and cannot be replaced by currently available digital denoising methodologies. Overall, we find that adding single-channel denoising as a component in the processing workflow can benefit a variety of infrasound signal detection, association, and location schemes. The denoising methods can also isolate the noise itself, with utility in statistically characterizing ambient infrasound noise.
more »
« less
Updated Global Reference Models of Broadband Coherent Infrasound Signals for Atmospheric Studies and Civilian Applications
Abstract The International Monitoring System (IMS) infrasound network has been established to detect nuclear explosions and other signals of interest embedded in the station‐specific ambient noise. The ambient noise can be separated into coherent infrasound (e.g., real infrasonic signals) and incoherent noise (such as that caused by wind turbulence). Previous work statistically and systematically characterized coherent infrasound recorded by the IMS. This paper expands on this analysis of the coherent ambient infrasound by including updated IMS data sets with data up to the end of 2020 for all 53 of the currently certified IMS infrasound stations using an updated configuration of the Progressive Multi‐Channel Correlation (PMCC) method. This paper presents monthly station‐dependent reference curves for the back azimuth, trace velocity, and root mean squared amplitude, which provides a means to determine the deviation from the nominal monthly behavior. In addition, a daily Ambient Noise Stationarity (ANS) factor based on deviations from the reference curves is determined for a quick reference to the coherent signal quality compared to the nominal situations. Newly presented histograms provide a higher resolution spectrum, including the observations of the microbarom peak, as well as additional peaks reflecting station‐dependent environmental noise. The aim of these reference curves is to identify periods of suboptimal operation (e.g., nonoperational sensor) or instances of strong abnormal signals of interest.
more »
« less
- Award ID(s):
- 1847736
- PAR ID:
- 10446857
- Publisher / Repository:
- DOI PREFIX: 10.1029
- Date Published:
- Journal Name:
- Earth and Space Science
- Volume:
- 9
- Issue:
- 7
- ISSN:
- 2333-5084
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract. The International Monitoring System (IMS) was established in the late 1990sfor verification of the Comprehensive Nuclear-Test-Ban Treaty (CTBT). Uponcompletion, 60 infrasound stations distributed over the globe will monitorthe Earth's atmosphere for low-frequency pressure waves. In this study, wepresent advanced infrasound data products of the 53 currently certified IMSinfrasound stations for atmospheric studies and civilian applications. Forthis purpose, 18 years of raw IMS infrasound waveform data (2003–2020) were reprocessed using the Progressive Multi-Channel Correlation (PMCC) method. A one-third octave frequency band configuration between 0.01 and 4 Hz was chosen to run this array-processing algorithm which detects coherent infrasound waves within the background noise. From the comprehensive detection lists, four products were derived for each of the certified 53 IMS infrasound stations. The four products cover different frequency ranges and are provided at the following different temporal resolutions: a very low-frequency set (0.02–0.07 Hz, 30 min; https://doi.org/10.25928/bgrseis_bblf-ifsd, Hupe et al., 2021a), two so-called microbarom frequency sets – covering both the lower (0.15–0.35 Hz, 15 min; https://doi.org/10.25928/bgrseis_mblf-ifsd, Hupe et al., 2021b) and a higher (0.45–0.65 Hz, 15 min; https://doi.org/10.25928/bgrseis_mbhf-ifsd, Hupe et al., 2021c) part – named after the dominant ambient noise of interacting ocean waves that are quasi-continuously detected at IMS stations, and observations with center frequencies of 1 to 3 Hz (5 min), called the high-frequency product (https://doi.org/10.25928/bgrseis_bbhf-ifsd, Hupe et al., 2021d). Within these frequency ranges and time windows, the dominant repetitive signal directions are summarized. Along with several detection parameters, calculated quantities for assessing the relative quality of the products are provided. The validity of the data products is demonstrated through example case studies of recent events that produced infrasound detected at IMS infrasound stations and through a global assessment and summary of the products. The four infrasound data products cover globally repeating infrasound sources such as ocean ambient noise or persistently active volcanoes, which have previously been suggested as sources for probing the winds in the middle atmosphere. Therefore, our infrasound data products open up the IMS observations also to user groups who do not have unconstrained access to IMS data or who are unfamiliar with infrasound data processing using the PMCC method. These types of data products could potentially serve as a basis for volcanic eruption early warning systems in the future.more » « less
-
Abstract Ambient infrasound noise contains an abundance of information that is typically overlooked due to limitations of typical infrasound arrays. To evaluate the ability of large‐N infrasound arrays to identify weak signals hidden in background noise, we examine data from a 22‐element array in central Idaho, USA, spanning 58 days using a standard beamforming method. Our results include nearly continuous detections of diverse weak signals from infrasonic radiators, sometimes at surprising distances. We observe infrasound from both local (8 km) and distant (195 km) waterfalls. Thunderstorms and earthquakes are also notable sources, with distant thunderstorm infrasound observed from ∼800 to 900 km away. Our findings show that large‐N infrasound arrays can detect very weak signals below instrument and environmental noise floors, including from multiple simultaneous sources, enabling new infrasound monitoring applications and helping map the composition of background noise wavefields.more » « less
-
Abstract The addition of 108 infrasound sensors—a legacy of the temporary USArray Transportable Array (TA) deployment—to the Alaska regional network provides an unprecedented opportunity to quantify the effects of a diverse set of site conditions on ambient infrasound noise levels. TA station locations were not chosen to optimize infrasound performance, and consequently span a dramatic range of land cover types, from temperate rain forest to exposed tundra. In this study, we compute power spectral densities for 2020 data and compile new ambient infrasound low- and high-noise models for the region. In addition, we compare time series of root-mean-squared (rms) amplitudes with wind data and high-resolution land cover data to derive noise–wind speed relationships for several land cover categories. We observe that noise levels for the network are dominated by wind, and that network noise is generally higher in the winter months when storms are more frequent and the microbarom is more pronounced. Wind direction also exerts control on noise levels, likely as a result of infrasound ports being systematically located on the east side of the station huts. We find that rms amplitudes correlate with site land cover type, and that knowledge of both land cover type and wind speed can help predict infrasound noise levels. Our results show that land cover data can be used to inform infrasound station site selection, and that wind–noise models that incorporate station land cover type are useful tools for understanding general station noise performance.more » « less
-
Abstract Seismic and infrasound multistation ambient‐noise interferometry has been widely used to infer ground and atmospheric properties, and single‐station and autocorrelation seismic interferometry has also shown potential for characterizing Earth structure at multiple scales. We extend autocorrelation seismic interferometry to ambient atmospheric infrasound recordings that contain persistent local noise from waterfalls and rivers. Across a range of geographic settings, we retrieve relative sound‐speed changes that exhibit clear diurnal oscillations consistent with temperature and wind variations. We estimate ambient air temperatures from variations in relative sound speeds. The frequency band from 1 to 2 Hz appears most suitable to retrieve weather parameters as nearby waterfalls and rivers may act as continuous and vigorous sources of infrasound that help achieve convergence of coherent phases in the autocorrelation codas. This frequency band is also appropriate for local sound‐speed variations because it has infrasound with wavelengths of ∼170–340 m, corresponding to a typical atmospheric boundary layer height. After applying array analysis to autocorrelation functions derived from a three‐element infrasound array, we find that autocorrelation codas are composed of waves reflected off nearby topographic features, such as caldera walls. Lastly, we demonstrate that autocorrelation infrasound interferometry offers the potential to study the atmosphere over at least several months and with a fine time resolution.more » « less
