skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Using Footpad Sculpturing to Enhance the Maneuverability and Speed of a Robotic Marangoni Surfer
From insects to arachnids to bacteria, the surfaces of lakes and ponds are teaming with life. Many modes of locomotion are employed by these organisms to navigate along the air–water interface, including the use of lipid-laden excretions that can locally change the surface tension of the water and induce a Marangoni flow. In this paper, we improved the speed and maneuverability of a miniature remote-controlled robot that mimics insect locomotion using an onboard tank of isopropyl alcohol and a series of servomotors to control both the rate and location of alcohol release to both propel and steer the robot across the water. Here, we studied the effect of a series of design changes to the foam rubber footpads, which float the robot and are integral in efficiently converting the alcohol-induced surface tension gradients into propulsive forces and effective maneuvering. Two designs were studied: a two-footpad design and a single-footpad design. In the case of two footpads, the gap between the two footpads was varied to investigate its impact on straight-line speed, propulsion efficiency, and maneuverability. An optimal design was found with a small but finite gap between the two pads of 7.5 mm. In the second design, a single footpad without a central gap was studied. This footpad had a rectangular cut-out in the rear to capture the alcohol. Footpads with wider and shallower cut-outs were found to optimize efficiency. This observation was reinforced by the predictions of a simple theoretical mechanical model. Overall, the optimized single-footpad robot outperformed the two-footpad robot, producing a 30% improvement in speed and a 400% improvement in maneuverability.  more » « less
Award ID(s):
1749634
PAR ID:
10475795
Author(s) / Creator(s):
; ; ;
Publisher / Repository:
MDPI
Date Published:
Journal Name:
Biomimetics
Volume:
8
Issue:
5
ISSN:
2313-7673
Page Range / eLocation ID:
440
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; (, Bioinspiration & Biomimetics)
    Abstract Inspired by creatures that have naturally mastered locomotion on the air–water interface, we developed and built a self-powered, remotely controlled surfing robot capable of traversing this boundary by harnessing surface tension modification for both propulsion and steering through a controlled release of isopropyl alcohol. In this process, we devised and implemented novel release valve and steering mechanisms culminating in a surfer with distinct capabilities. Our robot measures about 110 mm in length and can travel as fast as 0.8 body length per second. Interestingly, we found that the linear speed of the robot follows a 1/3 power law with the release rate of the propellant. Additional maneuverability tests also revealed that the robot is able to withstand 20 mm s −2 in centripetal acceleration while turning. Here, we thoroughly discuss the design, development, performance, overall capabilities, and ultimate limitations of our robotic surfer. 
    more » « less
  2. ; ; (, 2023 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS))
    To facilitate the study of how passive leg stiffness influences locomotion dynamics and performance, we have developed an affordable and accessible 400 g quadruped robot driven by tunable compliant laminate legs, whose series and parallel stiffness can be easily adjusted; fabrication only takes 2.5 hours for all four legs. The robot can trot at 0.52 m/s or 4.4 body lengths per second with a 3.2 cost of transport (COT). Through locomotion experiments in both the real world and simulation we demonstrate that legs with different stiffness have an obvious impact on the robot’s average speed, COT, and pronking height. When the robot is trotting at 4 Hz in the real world, changing the leg stiffness yields a maximum improvement of 37.1% in speed and 62.0% in COT, showing its great potential for future research on locomotion controller designs and leg stiffness optimizations. 
    more » « less
  3. ; ; ; ; ; ; (, Science Advances)
    Insect-scale robots face two major locomotive challenges: constrained energetics and large obstacles that far exceed their size. Terrestrial locomotion is efficient yet mostly limited to flat surfaces. In contrast, flight is versatile for overcoming obstacles but requires high power to stay aloft. Here, we present a hopping design that combines a subgram flapping-wing robot with a telescopic leg. Our robot can hop continuously while controlling jump height and frequency in the range of 1.5 to 20 centimeters and 2 to 8.4 hertz. The robot can follow positional set points, overcome tall obstacles, and traverse challenging surfaces. It can also hop on a dynamically rotating plane, recover from strong collisions, and perform somersaults. Compared to flight, this design reduces power consumption by 64 percent and increases payload by 10 times. Although the robot relies on offboard power and control, the substantial payload and efficiency improvement open opportunities for future study on autonomous locomotion. 
    more » « less
  4. ; ; ; (, Journal of fluids engineering)
    null (Ed.)
    The Marangoni propulsion of spheres and elliptical disks floating on the air–water interface were studied to understand the effect of particle shape on its motion and its stability at moderate Reynolds numbers. Self-propulsion of the Marangoni surfer was achieved by coating half of the spheres and the elliptical disks with either a solution of soap or isopropyl alcohol (IPA). The presence of the soap or IPA resulted in a surface tension gradient across the particles which propelled the particles in the direction of increasing surface tension. Beyond a critical velocity, a transition was observed from a straight-line motion to a rotational motion. These vortices were observed to shed above a critical Reynolds number resulting in an unbalanced torque that caused the particles to rotate. Increasing the aspect ratio between the major and minor axes of the elliptical disks was found to decrease their stability and greatly enhance their rate of rotation. This was especially true for elliptical disks traveling in a direction parallel to their major axis. The interactions between the particles and the wall of a Petri dish were also studied. Repulsive, concave curvature was found to decrease stability and enhance rotational motion, while attractive, convex curvature was shown to stabilize the straight-line motion of the spheres. For the neutrally buoyant elliptical disks, the presence of the bounding wall was found to greatly stabilize the straight-line motion of the elliptical disks when they were traveling in a direction parallel to their minor axis. 
    more » « less
  5. (, IEEE International Conference on Soft Robotics)
    Soft robots struggle with terrestrial locomotion due to their inherent lack of rigidity, specifically along axes not in line with the direction of actuation (side loads). We present a method for improved stiffness in a 3D printed, tendon-driven soft actuator. We show, both mathematically and experimentally, that our method leads to improved stiffness to these side loads. Additionally, we demonstrate the use of complex tendon routing schemes to achieve various trajectories with a single actuator morphology. Finally, we demonstrate that these two tendon routing strategies lead to improved locomotion speed and gait efficiency in a 3- legged, 3D printed, soft robot. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email