Amorphous Li 3 PS 4 (LPS) solid-state electrolytes are promising for energy-dense lithium metal batteries. LPS glass, synthesized from a 3 : 1 mol ratio of Li 2 S and P 2 S 5 , has high ionic conductivity and can be synthesized by ball milling or solution processing. Ball milling has been attractive because it provides the easiest route to access amorphous LPS with a conductivity of 3.5 × 10 −4 S cm −1 (20 °C). However, achieving the complete reaction of precursors via ball milling can be difficult, and most literature reports use X-ray diffraction (XRD) or Raman spectroscopy to confirm sample purity, both of which have limitations. Furthermore, the effect of residual precursors on ionic conductivity and lithium metal cycling is unknown. In this work, we illustrate the importance of multimodal characterization to determine LPS phase and chemical purity. To determine the residual Li 2 S content in LPS, we show that (1) XRD and 31 P solid state nuclear magnetic resonance (ssNMR) are insufficient and (2) Raman loses sensitivity at concentrations below 12 mol% Li 2 S. Most importantly, we show that 7 Li ssNMR is highly sensitive. Using 7 Li ssNMR, we investigate the effect of ball milling parameters and develop a robust and highly reproducible procedure for pure LPS synthesis. We find that as the residual Li 2 S precursor content increases, LPS conductivity decreases and lithium metal batteries exhibit higher overpotentials and poor cycle life. Our work reveals the importance of multimodal characterization techniques for amorphous solid-state electrolyte characterization and will enable better synthetic strategies for highly conductive electrolytes for efficient energy-dense solid-state lithium metal batteries.
more »
« less
Impact of Processing Methodology on the Performance of Hybrid Sulfide-Polymer Solid State Electrolytes for Lithium Metal Batteries
Hybrid sulfide-polymer composite electrolytes are promising candidates to enable lithium metal batteries because of their high ionic conductivity and flexibility. These composite materials are primarily prepared through solution casting methods to obtain a homogenous distribution of polymer within the inorganic. However, little is known about the influence of the morphology of the polymer and the inorganic on the ionic conductivity and electrochemical behavior of these hybrid systems. In this study, we assess the impact of processing methodology, either solution processing or solvent-free ball milling, on overall performance of hybrid electrolytes containing amorphous Li3PS4(LPS) and non-reactive polyethylene (PE). We demonstrate that using even non-polar, non-reactive solvents can alter the LPS crystalline structure, leading to a lower ionic conductivity. Additionally, we show that ball milling leads to a non-homogenous distribution of polymer within the inorganic, which leads to a higher ionic conductivity than samples processed via solution casting. Our work demonstrates that the morphology of the polymer and the sulfide plays a key role in the ionic conductivity and subsequent electrochemical stability of these hybrid electrolytes.
more » « less- PAR ID:
- 10494526
- Publisher / Repository:
- The Electrochemical Society
- Date Published:
- Journal Name:
- Journal of The Electrochemical Society
- Volume:
- 171
- Issue:
- 3
- ISSN:
- 0013-4651
- Format(s):
- Medium: X Size: Article No. 030508
- Size(s):
- Article No. 030508
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Hybrid solid electrolytes are composed of organic (polymer) and inorganic (ceramic) ion conducting materials, and are promising options for large-scale production of solid state lithium–metal batteries. Hybrid solid electrolytes containing 15 vol% Al-LLZO demonstrate optimal ionic conductivity properties. Ionic conductivity is shown to decrease at high inorganic loadings. This optimum is most obvious above the melting temperature of polyethylene oxide where the polymer is amorphous. Structural analysis using synchrotron nanotomography reveals that the inorganic particles are highly aggregated. The aggregation size grows with inorganic content and the largest percolating clusters measured for 5 vol%, 15 vol% and 50 vol% were ∼12 μm 3 , 206 μm 3 , and 324 μm 3 , respectively. Enhanced transport in hybrid electrolytes is shown to be due to polymer|particle (Al-LLZO) interactions and ionic conductivity is directly related to the accessible surface area of the inorganic particles within the electrolyte. Ordered and well-dispersed structures are ideal for next generation hybrid solid electrolytes.more » « less
-
more » « less
Abstract Rechargeable solid‐state sodium metal batteries (SSMBs) experience growing attention owing to the increased energy density (vs Na‐ion batteries) and cost‐effective materials. Inorganic sulfide‐based Na‐ion conductors also possess significant potential as promising solid electrolytes (SEs) in SSMBs. Nevertheless, due to the highly reactive Na metal, poor interface compatibility is the biggest obstacle for inorganic sulfide solid electrolytes such as Na3SbS4to achieve high performance in SSMBs. To address such electrochemical instability at the interface, new design of sulfide SE nanostructures and interface engineering are highly essential. In this work, a facile and straightforward approach is reported to prepare 3D sulfide‐based solid composite electrolytes (SCEs), which utilize porous Na3SbS4(NSS) as a self‐templated framework and fill with a phase transition polymer. The 3D structured SCEs display obviously improved interface stability toward Na metal than pristine sulfide. The assembled SSMBs (with TiS2or FeS2as cathodes) deliver outstanding electrochemical cycling performance. Moreover, the cycling of high‐voltage oxide cathode Na0.67Ni0.33Mn0.67O2(NNMO) is also demonstrated in SSMBs using 3D sulfide‐based SCEs. This study presents a novel design on the self‐templated nanostructure of SCEs, paving the way for the advancement of high‐energy sodium metal batteries.
-
more » « less
Structural supercapacitors, capable of bearing mechanical loads while storing electrical energy, hold great promise for enhancing mobile system efficiencies. However, developing practical structural supercapacitors often involves a challenging balance between mechanical and electrochemical performance, particularly in their electrolytes. Traditional research has focused on bi-continuous phase electrolytes (BPEs), which typically comprise high liquid content that weakens mechanical strength, and inert solid phases that hinder ion conduction and block electrode surfaces. Our previous work introduces a novel approach with a hydrated polymer electrolyte, demonstrating enhanced multifunctionality. This electrolyte, derived from controlled hydration of PET-LiClO4, forms a trihydrate (LiClO4∙3H2O) structure, where water molecules bond with ions without forming a liquid phase, thereby improving ion mobility while maintaining the base polymer's mechanical properties. This new design also promotes better electrochemical interfaces with electrodes, a significant advancement over traditional BPEs.
In this study, we further enhance the performance and processability of such hydrated polymer electrolytes by incorporating polylactic acid (PLA) as the base polymer and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) as the salt. The electrolyte, prepared through solution casting and subsequent controlled hydration, consistently remains an amorphous solid solution in both dry and hydrated states, as confirmed by DSC, XRD, and FTIR analyses. Our tests on ionic conductivity and mechanical properties reveal that adding water to the polymer electrolyte substantially increases ionic conductivity while retaining mechanical properties. A specific composition demonstrated a remarkable increase in ionic conductivity coupled with superior toughness surpassing the base polymer. Furthermore, we successfully fabricated and tested structural supercapacitor devices made of composites of carbon fibers and these new electrolytes. The prototypes presented enhanced toughness with significant energy storage performance, demonstrating their vast application potential due to their outstanding multifunctionality.
-
more » « less
Abstract Enabling all‐solid‐state Li‐ion batteries requires solid electrolytes with high Li ionic conductivity and good electrochemical stability. Following recent experimental reports of Li3YCl6and Li3YBr6as promising new solid electrolytes, we used first principles computation to investigate the Li‐ion diffusion, electrochemical stability, and interface stability of chloride and bromide materials and elucidated the origin of their high ionic conductivities and good electrochemical stabilities. Chloride and bromide chemistries intrinsically exhibit low migration energy barriers, wide electrochemical windows, and are not constrained to previous design principles for sulfide and oxide Li‐ion conductors, allowing for much greater freedom in structure, chemistry, composition, and Li sublattice for developing fast Li‐ion conductors. Our study highlights chloride and bromide chemistries as a promising new research direction for solid electrolytes with high ionic conductivity and good stability.
