A dissimilar weld between a low alloy steel (LAS) butter weld joined to a F65 steel pipe using a narrow groove hot wire gas tungsten arc welding (HW-GTAW) procedure with Alloy 625 filler metal was investigated. The weld interpass microstructure is comprised of large swirls formed by a macrosegregation mechanism involving partial, non-uniform mixing of liquid base metal with the lower melting temperature weld pool, followed by fast solidification. This mechanism produces steep gradients in composition and solidification behavior. The resulting swirls are composed of alternating iron-rich peninsulas and partially mixed zones (PMXZ) that are surrounded by planar and cellular zones exhibiting multiple solidification directions. Large austenitic grains, encompassing planar, cellular, and dendritic morphologies, nucleate off peninsulas in direct contact with the weld pool. The highest hardness was found in nickel and chromium rich PMXZs that exhibited a lath martensite microstructure. In the event of exposure to hydrogen containing environments, the PMXZs could serve as nucleation sites for hydrogen assisted cracking.
more »
« less
This content will become publicly available on March 1, 2025
Low alloy steel girth welds in X65 steel pipes internally clad with alloy 625: Part I: Materials selection and process development
API 5L Grade X65 steel pipes, internally clad alloy 625, are commonly utilized in pipelines and risers for subsea oil and gas extraction. Gird welds in such pipes are conventionally made using alloy 625 filler metal. However, alloy 625 weld metal cannot meet the base metal yield strength overmatching requirement for subsea reel lay installation. This study explored materials selection and process development for low-alloy steel girth welds in API 5L Grade X65 steel pipes, internally clad with alloy 625. Welding with a higher melting point filler metal over a lower melting substrate, i.e., low-alloy steel over Ni-based alloy, is impractical due to increased susceptibility to solidification cracking and solidification shrinkage porosity. Pseudo-binary phase diagrams developed for various combinations of low alloy steel filler metals and Ni-based alloy substrates identified good compatibility between ER80S-G filler metal and alloy 686. The solidification temperature range and the tendency for partitioning of alloying elements were significantly lower throughout the entire ER80S-G/alloy 686 dilution range than in the low alloy steel filler metals/alloy 625 combinations. Extensive process optimization effort to reduce the dilution of alloy 686 root pass in the low-alloy steel weld metal and avoid incomplete fusion defects allowed for the production of defect-free girth welds. These welds met the yield strength and ductility requirements for subsea reel lay installation of pipelines. Process optimization for bead tempering significantly narrowed the high hardness region in the ER80S-G/alloy 686 partially mixed zone.
more »
« less
- Award ID(s):
- 2052747
- NSF-PAR ID:
- 10506947
- Publisher / Repository:
- Springer
- Date Published:
- Journal Name:
- Welding in the World
- Volume:
- 68
- Issue:
- 3
- ISSN:
- 0043-2288
- Page Range / eLocation ID:
- 637 to 655
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
more » « less
This study addresses the limitations of cross weld tensile testing (CWTT) in quantifying local mechanical properties across microstructural and compositional gradients in dissimilar– and matching–filler metal welds. A digital image correlation (DIC) methodology was validated for application in CWTT by direct comparison of stress-strain curves generated using conventional and virtual DIC extensometers in tensile testing of homogeneous steel samples. DIC-instrumented CWTT of dissimilar weld metal Alloy 625 filler metal on F65 steel demonstrated capability in quantifying the local yield strength, strain-hardening kinetics, and strain at failure in the base metal, heat-affected zone (HAZ), fusion boundary (FB) region, and weld metal in dissimilar and matching filler metal welds. It was shown that the high strain-hardening capacity in Alloy 625 weld metal led to base metal failure in CWTT despite the lower Alloy 625 weld metal yield strength. It was also shown that DIC-instrumented CWTT can be used for determining weld metal undermatching and overmatching conditions in compositionally matching- and dissimilar-metal welds. Furthermore, by quantifying local strain distribution (both elastic and plastic) in the HAZ, FB region, and weld metal, DIC-instrumented CWTT provides an additional method for evaluating hydrogen-assisted cracking susceptibility in dissimilar-metal welds.
-
The local yielding behavior in base metal, heat-affected zone, fusion boundary region, and weld metal of low-alloy steel/Alloy 625 filler metal welds was quantified using digital image correlation instrumented cross-weld tensile test. The tested welds exhibited undermatching, matching, or overmatching weld metal yield strength with significant gradients in the local yielding behavior. An undermatching weld yielded at 69 MPa below the base metal yield stress, accumulating to 0.72% total strain. The base metal in an overmatching weld had 110 MPa lower yield strength than the weld metal. The strong strain hardening response in the Alloy 625 weld metal, within the uniform elongation range, and its constraining effect on the fusion boundary region and heat affected zone, led to extensive strain accumulation, necking, and final failure in the base metal of all tested welds. The yielding behavior of the tested welds was compared to stress-based criteria, utilizing minimum specified and as-delivered yield and ultimate tensile strength, and to strain-based criteria. The capability of digital image correlation instrumented cross-weld tensile testing to quantify local yielding and strain accumulation demonstrates potential application in proving conformity to stress-based and strain-based design criteria of dissimilar and matching filler metal welds.more » « less
-
Dissimilar metal welds (DMWs) are commonly used when a high strength steel is overlaid with a corrosion resistant alloy (CRA) for petrochemical applications. There have been reported failures of these DMWs during subsea service while under cathodic protection (CP). These failures are caused by local hydrogen embrittlement of susceptible microstructures that form at the weld fusion boundary. Hydrogen-assisted cracking (HAC) occurs as a result of the local embrittlement and is influenced by base/filler metal combinations, and welding and post-weld heat treatment (PWHT) procedures. A delayed hydrogen cracking test was used to simulate tensile load and hydrogen charging on 8630-FM 625 weld. The failure of this sample was recorded using a high-speed camera to capture the crack initiation and propagation during failure. Fractography was performed using a scanning electron microscope (SEM) along with energy dispersive spectroscopy (EDS). The fracture surfaces, EDS measurement and video timestamps revealed brittle fracture nucleation in the planar growth and CGHAZ regions of the weld. The cracking continued to propagate through the same regions of the weld leading to final ductile failure (microvoid coalescence) in the cellular dendritic region of the weld.more » « less
-
Dissimilar metal welds (DMWs) are routinely used in the oil and gas industries for structural joining of high-strength steels to eliminate the need for post-weld heat treatment (PWHT) in field welding. Hydrogen-assisted cracking (HAC) can occur in DMWs during subsea service under cathodic protection. DMWs of two material combinations, 8630 steel/FM 625 and F22 steel/FM 625, produced with two welding procedures, non-temper bead (BS1) and temper bead (BS3), in the as-welded and PWHT conditions were investigated in this study. These DMWs were subjected to metallurgical characterization and testing with the delayed hydrogen cracking test (DHCT) to identify the effects of base metal composition, welding and PWHT procedures on their HAC susceptibility. The HAC susceptibility was ranked using the time to failure in the DHCT at loads equivalent to 90% of the base metal yield strength (YS) and the apparent stress threshold for HAC. A criterion for resistance to HAC in the testing conditions of DHCT was also established. The results of this study showed that 8630/FM 625 DMWs were more susceptible to HAC than the F22/FM 625 DMWs. PWHT did not sufficiently reduce the HAC susceptibility of the 8630/FM 625 and F22/FM 625 BS1 welds. DMWs produced using BS3 performed better than BS1 DMWs. The post-weld heat-treated F22/FM 625 BS3 DMW passed the HAC resistance criterion.more » « less
