An official website of the United States government
Recently, augmented reality (AR) displays have attracted considerable attention due to the highly immersive and realistic viewer experience they can provide. One key challenge of AR displays is the fundamental trade-off between the extent of the field-of-view (FOV) and the size of the eyebox, set by the conservation of etendue sets this trade-off. Exit-pupil expansion (EPE) is one possible solution to this problem. However, it comes at the cost of distributing light over a larger area, decreasing the overall system's brightness. In this work, we show that the geometry of the waveguide and the in-coupler sets a fundamental limit on how efficient the combiner can be for a given FOV. This limit can be used as a tool for waveguide designers to benchmark the in-coupling efficiency of their in-coupler gratings. We design a metasurface-based grating (metagrating) and a commonly used SRG as in-couplers using the derived limit to guide optimization. We then compare the diffractive efficiencies of the two types of in-couplers to the theoretical efficiency limit. For our chosen waveguide geometry, the metagrating's 28% efficiency surpasses the SRG's 20% efficiency and nearly matches the geometry-based limit of 29% due to the superior angular response control of metasurfaces compared to SRGs. This work provides new insight into the efficiency limit of waveguide-based combiners and paves a novel path toward implementing metasurfaces in efficient waveguide AR displays.
more »
« less
Efficient all-dielectric metasurface in-coupler for waveguide-based near-eye display
The creation of new see-through near-eye displays (NEDs) architectures is a topic of intense research focus. A fundamental problem that each design must address is the field of view (FOV) and eyebox of NEDs are limited by etendue conservation for a fixed display optics size. Waveguide architecture provides the solution to increasing the eyebox in NEDs without increasing the optics size through exit pupil expansion. Brightness and uniformity are two key features of waveguide architecture. In this work, we focus on the brightness of the waveguide since the image uniformity can be compensated by the display engine. We show that the geometry of the waveguide sets a fundamental limit on the in-coupling efficiency for a given FOV. This limit can be used as a tool for waveguide designers to benchmark the in-coupling efficiency of their incoupler gratings. With this derived limit, we designed and optimized a metasurface-based grating (metagrating) and a surface relief grating (SRG) as in-couplers. The diffractive efficiencies of the two types of in-couplers were then compared to the theoretical efficiency limit. The metagrating's 28% efficiency surpasses the SRG's 20% efficiency and nearly matches the geometry-based limit of 29% due to the superior angular response control of metasurfaces compared to SRGs. This work provides a new understanding of the brightness efficiency limit of waveguide-based combiners and paves a novel path toward implementing metasurfaces in efficient waveguide AR displays.
more »
« less
- PAR ID:
- 10517979
- Editor(s):
- Kress, Bernard C; Peroz, Christophe
- Publisher / Repository:
- SPIE
- Date Published:
- Journal Name:
- SPIE
- ISBN:
- 9781510660038
- Page Range / eLocation ID:
- 3
- Format(s):
- Medium: X
- Location:
- San Francisco, United States
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Metasurfaces have been rapidly advancing our command over the many degrees of freedom of light within compact, lightweight devices. However, so far, they have mostly been limited to manipulating light in free space. Grating couplers provide the opportunity of bridging far-field optical radiation and in-plane guided waves, and thus have become fundamental building blocks in photonic integrated circuits. However, their operation and degree of light control is much more limited than metasurfaces. Metasurfaces integrated on top of guided wave photonic systems have been explored to control the scattering of light off-chip with enhanced functionalities – namely, point-by-point manipulation of amplitude, phase or polarization. However, these efforts have so far been limited to controlling one or two optical degrees of freedom at best, and to device configurations much more complex compared to conventional grating couplers. Here, we introduce leaky-wave metasurfaces, which are based on symmetry-broken photonic crystal slabs that support quasi-bound states in the continuum. This platform has a compact form factor equivalent to the one of conventional grating couplers, but it provides full command over amplitude, phase and polarization (four optical degrees of freedom) across large apertures. We present experimental demonstrations of various functionalities for operation at λ= 1.55 μm based on leaky-wave metasurfaces, including devices for phase and amplitude control at a fixed polarization state, and devices controlling all four optical degrees of freedom. Our results merge the fields of guided and free-space optics under the umbrella of metasurfaces, exploiting the hybrid nature of quasi-bound states in the continuum, for opportunities to advance in disruptive ways imaging, communications, augmented reality, quantum optics, LIDAR, and integrated photonic systems.more » « less
-
Three-dimensional (3D) vision in augmented reality (AR) displays can enable highly immersive and realistic viewer experience, hence, attracts much attention. Most current approaches create 3D vision by projecting stereoscopic images to different eyes using two separate projection systems, which are inevitably bulky for wearable devices. Here, we propose a compact stereo waveguide AR display system using a single piece of thin flat glass integrated with a polarization-multiplexed metagrating in-coupler and two diffractive grating out-couplers. Incident light of opposite circular polarization states carrying stereoscopic images are first steered by the metagrating in-coupler to opposite propagation directions in the flat glass waveguide, subsequently extracted by the diffractive grating out-couplers, and finally received by different eyes, forming 3D stereo vision. Experimentally, we fabricated a display prototype and demonstrated independent projection of two polarization-multiplexed stereoscopic images.more » « less
-
We report the realization of efficiently coupled 3D tapered waveguide-to-fiber couplers (TWCs) based on standard lithography techniques. The 3D TWC design is capable of achieving highly efficient flat-cleaved fiber to silicon nitride photonic waveguide coupling, withT ≈ 95 % polarization-insensitive coupling efficiency, wide bandwidth, and good misalignment tolerance. Our fabricated 3D TWCs on a functional nanophotonic circuit achieveT ≈ 85% coupling efficiency. Beyond applications in high-efficiency photon coupling, the demonstrated 3D lithography technique provides a complementary approach for mode field shaping and effective refractive index engineering, potentially useful for general applications in integrated photonic circuits.more » « less
-
Density-based topology optimization is used to design large-scale, multi-layer grating couplers that comply with commercial foundry fabrication constraints while simultaneously providing beam profiles that efficiently couple to a single-mode optical fiber without additional optics. Specifically, we describe the design process and experimentally demonstrate both single- and dual-polarization grating couplers that couple at normal incidence (0° from the normal) with low backreflections (-13.7 dB and -15.4 dB at the center wavelength), broad 3 dB bandwidths (75 nm and 89 nm), and standard coupling efficiencies (-4.7 dB and -7.0 dB). The dual-polarization grating couplers exhibit over 30 dB of polarization extinction across the entire band. The devices were fabricated on the GlobalFoundries 45CLO CMOS platform and characterized across three separate wafers. This new design approach produces distinct features for multiple foundry layers and yields emitters with arbitrary, user-specified far-field profiles.more » « less
