An official website of the United States government
Abstract The mechanical response of a knot tied in elastic rods strongly depends on the frictional force due to rod–rod contact. The behavior of a knot can be qualitatively different based on the frictional coefficient of the elastic rod. Systematic variation of friction during rod–rod contact is a crucial component of any experimental design to uncover the underlying ingredients behind the mechanics of knots. In this paper, we demonstrate a novel process of controlling the friction of a continuous rod by adhering non-spherical inorganic micro-particles. Polymeric binder is used to deliver the particles as asperities over the rod substrate and by controlling their size and distribution the coefficient of friction of the rod is determined. In parallel, numerical simulations with the discrete elastic rods algorithm are used to reproduce the experimental observations. Tabletop experiments are performed where overhand knots with a variety of unknotting numbers are pulled tight. The force–extension curve of these experiments shows that the proposed process can successfully tune the friction between rods.
more »
« less
Mechanical Response of Fisherman’s Knots During Tightening
Abstract The fisherman’s knot, renowned for its strength and reliability, finds applications in engineering and medicine. However, a comprehensive understanding of its mechanics remains limited in scientific literature. In this paper, we present a systematic study of the tightening behavior of the fisherman’s knot through a combined approach of tabletop experiments and discrete elastic rods simulations. Our experimental setup involves gradually applying tension to the two ends of the fisherman’s knot until it fractures. We observed a correlation between the knot’s material properties and its behavior during tightening, leading up to fracture. The tightening process of the fisherman’s knot exhibits distinct “sliding” or “stretching” motions, influenced by factors such as friction and elastic stiffness. Furthermore, the failure modes of the knot (material fracture and topological failure) are determined by an interplay between elastic stiffness, friction, and initial conditions. This study sheds light on the underlying mechanics of the fisherman’s knot and provides insight into its behavior during the tightening process, contributing to the broader understanding of the mechanics of knots in practical applications.
more »
« less
- PAR ID:
- 10524105
- Publisher / Repository:
- ASME
- Date Published:
- Journal Name:
- Journal of Applied Mechanics
- Volume:
- 91
- Issue:
- 3
- ISSN:
- 0021-8936
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Empirical slip-rate- and state-dependent friction laws and linear fracture mechanics constitute popular approaches to explaining earthquakes. However, the physics underlying friction laws remain elusive and fracture mechanics does not specify fault strength at the various conditions relevant to crustal faulting. Here, we introduce a physical constitutive framework that augments the traditional approaches by incorporating the real area of contact as the state variable. The physical model explains the dynamics of slow and fast ruptures on transparent materials, as well as the amount of light transmitted across the interface during laboratory ruptures. The constitutive framework elucidates the origin of empirical friction laws, and the simulated ruptures can be described by linear elastic fracture mechanics. Continuous measurements of the physical state variable or its proxies during seismic cycles emerge as a novel tool for probing natural faults and advancing our understanding of the earthquake phenomenon.more » « less
-
The double‐network (DN) concept, initially applied to hydrogels, has been adapted to elastomers, resulting in materials that combine exceptional toughness with tunable elasticity. This article delves into the constitutive and fracture behaviors of DN elastomers, elucidating the pivotal role of prestretch and composition in tailoring their properties. An incompressible hyperelastic model is employed to predict the stress–strain behavior and energy release rate of a DN elastomer, focusing on how the interactions between the two networks influence its overall material properties. The influence of prestretch and composition on increasing the stiffness and energy release rate of a DN elastomer is analytically determined. The analytical predictions are validated experimentally through comprehensive mechanical and fracture testing using a DN elastomer fabricated by a two‐step crosslinking process to decouple the prestretch and composition. The results show that manipulating these processing parameters can finely tune the mechanical responses of DN elastomers, optimizing them for specific applications. The findings provide new insights into the mechanics of DN elastomers.more » « less
-
ABSTRACT:Due to rock mass being commonly subjected to compressive or shear loading, the mode II fracture toughness is an important material parameter for rocks. Fracturing in rocks is governed by the behavior of a nonlinear region surrounding the crack tip called the fracture process zone (FPZ). However, the characteristics of mode II fracture are still determined based on the linear elastic fracture mechanics (LEFM), which assumes that a pure mode II loading results in a pure mode II fracture. In this study, the FPZ development in Barre granite specimens under mode II loading was investigated using the short beam compression (SBC) test. Additionally, the influence of lateral confinement on various characteristics of mode II fracture was studied. The experimental setup included the simultaneous monitoring of surface deformation using the two-dimensional digital image correlation technique (2D-DIC) to identify fracture mode and characterize the FPZ evolution in Barre granite specimens. The 2D-DIC analysis showed a dominant mixed-mode I/II fracture in the ligament between two notches, irrespective of confinement level on the SBC specimens. The influence of confinement on the SBC specimens was assessed by analyzing the evolution of crack displacement and changes in value of mode II fracture toughness. Larger levels of damage in confined specimens were observed prior to the failure than the unconfined specimens, indicating an increase in the fracture resistance and therefore mode II fracture toughness with the confining stress. 1. INTRODUCTIONThe fracturing in laboratory-scale rock specimens is often characterized by the deformation of the inelastic region surrounding the crack tips, also known as the fracture process zone (FPZ) (Backers et al., 2005; Ghamgosar and Erarslan, 2016). While the influence of the FPZ on mode I fracture in rocks has been extensively investigated, there are limited studies on FPZ development in rocks under pure mode II loading (Ji et al., 2016; Lin et al., 2020; Garg et al., 2021; Li et al., 2021).more » « less
-
null (Ed.)Purpose Mechanical anisotropy associated with material extrusion additive manufacturing (AM) complicates the design of complex structures. This study aims to focus on investigating the effects of design choices offered by material extrusion AM – namely, the choice of infill pattern – on the structural performance and optimality of a given optimized topology. Elucidation of these effects provides evidence that using design tools that incorporate anisotropic behavior is necessary for designing truly optimal structures for manufacturing via AM. Design/methodology/approach A benchmark topology optimization (TO) problem was solved for compliance minimization of a thick beam in three-point bending and the resulting geometry was printed using fused filament fabrication. The optimized geometry was printed using a variety of infill patterns and the strength, stiffness and failure behavior were analyzed and compared. The bending tests were accompanied by corresponding elastic finite element analyzes (FEA) in ABAQUS. The FEA used the material properties obtained during tensile and shear testing to define orthotropic composite plies and simulate individual printed layers in the physical specimens. Findings Experiments showed that stiffness varied by as much as 22% and failure load varied by as much as 426% between structures printed with different infill patterns. The observed failure modes were also highly dependent on infill patterns with failure propagating along with printed interfaces for all infill patterns that were consistent between layers. Elastic FEA using orthotropic composite plies was found to accurately predict the stiffness of printed structures, but a simple maximum stress failure criterion was not sufficient to predict strength. Despite this, FE stress contours proved beneficial in identifying the locations of failure in printed structures. Originality/value This study quantifies the effects of infill patterns in printed structures using a classic TO geometry. The results presented to establish a benchmark that can be used to guide the development of emerging manufacturing-oriented TO protocols that incorporate directionally-dependent, process-specific material properties.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1115/1.4063895
