An official website of the United States government
The viscosity and microstructure of Li-ion battery slurries and the performance of the resulting electrodes have been shown to depend on the mixing protocol. This work applies rheology to understand the impact of shear during mixing and polymer molecular weight on slurry microstructure and electrode performance. Mixing protocols of different shear intensity are applied to slurries of LiNi0.33Mn0.33Co0.33O2 (NMC), carbon black (CB), and polyvinyldiene difluoride (PVDF) in N-methyl-2-pyrrolidinone (NMP), using both high-molecular-weight (HMW) and low-molecular-weight (LMW) PVDF. Slurries of both polymers are observed to form colloidal gels under high-shear mixing, even though unfavorable interactions between high molecular weight PVDF and CB should prevent this microstructure from forming. Theoretical analysis and experimental results show that increasing shear rate during the polymer and particle mixing steps causes polymer scission to decrease the polymer molecular weight and allow colloidal gelation. In general, electrodes made from high molecular weight PVDF generally show increased rate capability. However, high shear rates lead to increased cell variability, possibly due to the heterogeneities introduced by polymer scission.
more »
« less
Electrochemical and mechanical characterization of thermosets as fluorine‐free cathode binders for Li‐ion batteries
Abstract This study demonstrates fluorine‐free cross‐linked (meth)acrylate polymers as alternatives to polyvinylidene fluoride (PVDF) in LiNi0.33Mn0.33Co0.33O2(NMC111) cathodes. We determine the effects of thermal initiator content, polymer content, and curing environment for two polymer chemistries: a flexible acrylate polymer, and a stiff methacrylate polymer. Electrodes are manufactured and tested for final electrochemical performance and mechanical properties. The results show that the flexible acrylate polymer exhibits higher rate capability compared to the stiff methacrylate polymer because calendering fractures the brittle network of stiff polymer. Electrode adhesion to the current collector and cohesion between particles are found to be a strong function of thermal initiator ratio and oxygen inhibition. Furthermore, there exists an optimal binder concentration that maximizes rate capability performance. Under the right conditions, the two polymers exhibit comparable performance to PVDF electrodes. These results provide important implications for designing cross‐linked polymers as cathode binder alternatives to PVDF.
more »
« less
- Award ID(s):
- 1929755
- PAR ID:
- 10536618
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- AIChE Journal
- Volume:
- 70
- Issue:
- 12
- ISSN:
- 0001-1541
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Electronic connections between active material particles and the conductive carbon binder domain govern high-energy commercial Li-ion batteries' rate capability and lifetime (LIB). This work develops an in situ electrochemical fluorescent microscopy (EFM) technique that maps fluorescence intensity to these local electronic connections. Specifically, rapid redox kinetics of an electrofluorophore translates to reaction distributions limited by the electronic accessibility of battery electrode regions and individual active material particles. This technique can visualize hot spots, dead zones, and isolated particles on the electrode surface. EFM characterization of a series of LiNi0.33Mn0.33Co0.33O2electrodes across processing parameters finds a significant negative correlation between the number of disconnected active particles and the rate capability. This low-cost technique provides quantitative mesoscale characterization of commercial LIB electrodes with fast throughput (<60 s) to facilitate rapid research and development and provide manufacturing quality control.more » « less
-
Self-healing polymers often have a trade-off between healing efficiency and mechanical stiffness. Stiff polymers that sacrifice their chain mobility are slow to repair upon mechanical failure. We herein report adaptable polymer films with dynamically moisture-controlled mechanical and optical properties, therefore having tunable self-healing efficiency. The design of the polymer film is based on the coordination of europium (Eu) with dipicolylamine (DPA)-containing random copolymers of poly( n -butyl acrylate- co -2-hydroxy-3-dipicolylamino methacrylate) (P( n BA- co -GMADPA)). The Eu–DPA complexation results in the formation of mechanically robust polymer films. The coordination of Eu–DPA has proven to be moisture-switchable given the preferential coordination of lanthanide metals to O over N, using nuclear magnetic resonance and fluorescence spectroscopy. Water competing with DPA to bind Eu 3+ ions can weaken the cross-linking networks formed by Eu–DPA coordination, leading to the increase of chain mobility. The in situ dynamic mechanical analysis and ex situ rheological studies confirm that the viscofluid and the elastic solid states of Eu-polymers are switchable by moisture. Water speeds up the self-healing of the polymer film by roughly 100 times; while it can be removed after healing to recover the original mechanical stiffness of polymers.more » « less
-
Longer and stronger; stiff but not brittle Hydrogels are highly water-swollen, cross-linked polymers. Although they can be highly deformed, they tend to be weak, and methods to strengthen or toughen them tend to reduce stretchability. Two papers now report strategies to create tough but deformable hydrogels (see the Perspective by Bosnjak and Silberstein). Wanget al. introduced a toughening mechanism by storing releasable extra chain length in the stiff part of a double-network hydrogel. A high applied force triggered the opening of cycling strands that were only activated at high chain extension. Kimet al. synthesized acrylamide gels in which dense entanglements could be achieved by using unusually low amounts of water, cross-linker, and initiator during the synthesis. This approach improves the mechanical strength in solid form while also improving the wear resistance once swollen as a hydrogel. —MSLmore » « less
-
Abstract Modification of a surface with polymer brushes has emerged as an effective approach to tune the properties of a substrate. Brushes grown from an inimer‐containing cross‐linkable polymer coating provide significant advantages compared to other “grafting‐from” methods, such as improved stability, increased grafting density, and the potential to control the grafting density. So far, the inimer coating method has only been applied for surface‐initiated controlled radical polymerizations. In this work, an approach is presented for the fabrication of a stable cross‐linked ultra‐thin polymer coating containing hydroxyl groups which serve as initiating sites for surface‐initiated ring‐opening polymerization (SI‐ROP). The polymers used for the fabrication of the coatings consist of 2‐((tetrahydro‐2H‐pyran‐2‐yl)oxy)ethyl methacrylate (THPEMA), a small fraction of a cross‐linkable unit, and a diluent styrene. Three coatings with varying THPEMA and styrene content are fabricated, and poly(dimethyl siloxane) (PDMS) and poly(caprolactone) (PCL) brushes are grown by SI‐ROP of hexamethylcyclotrisiloxane (D3), and ε‐caprolactone respectively. The brushes are characterized by atomic force microscopy (AFM), X‐ray photoelectron spectroscopy (XPS), static contact angle measurements, ellipsometry and size exclusion chromatography (SEC). The results demonstrate a well‐controlled ROP of D3and ability to control grafting density by tuning the THPEMA content of the coatings.more » « less
