An official website of the United States government
Thermoelectric materials enable the direct conversion of thermal energy to electricity. Ambient heat energy harvesting could be an effective route to convert buildings from being energy consumers to energy harvesters, thus making them more sustainable. There exists a relatively stable temperature gradient (storing energy) between the internal and external walls of buildings which can be utilized to generate meaningful energy (that is, electricity) using the thermoelectric principle. This could ultimately help reduce the surface temperatures and energy consumption of buildings, especially in urban areas. In this paper, ongoing work on developing and characterizing a cement-based thermoelectric material is presented. Samples are fabricated using cement as a base material and different metal oxides (Bi₂O₃ and Fe₂O₃) are added to enhance their thermoelectric properties. A series of characterization tests are undertaken on the prepared samples to determine their Seebeck coefficient, electrical and thermal conductivity. The study shows that cement paste with additives possesses physical properties in the range of semiconductors whereby, initially, the resistivity values are low but with time, they increase gradually, thus resulting in lower electrical conductivity. The thermal conductivity of the cement paste with additives is lower than the control sample. Seebeck coefficient values were found to be relatively unstable during the initial set of measurements because the internal and external environment needed to be kept in a thermally stable condition to achieve steady results. The detailed analysis helped determine and eliminate the source of errors in the characterization process and obtain repeatable results. Parameters such as moisture content, temperature, and age were found to have a significant impact on the properties of cement-based thermoelectric materials.
more »
« less
3D Soft Architectures for Stretchable Thermoelectric Wearables with Electrical Self‐Healing and Damage Tolerance
Abstract Flexible thermoelectric devices (TEDs) exhibit adaptability to curved surfaces, holding significant potential for small‐scale power generation and thermal management. However, they often compromise stretchability, energy conversion, or robustness, thus limiting their applications. Here, the implementation of 3D soft architectures, multifunctional composites, self‐healing liquid metal conductors, and rigid semiconductors is introduced to overcome these challenges. These TEDs are extremely stretchable, functioning at strain levels as high as 230%. Their unique design, verified through multiphysics simulations, results in a considerably high power density of 115.4 µW cm⁻2at a low‐temperature gradient of 10 °C. This is achieved through 3D printing multifunctional elastomers and examining the effects of three distinct thermal insulation infill ratios (0%, 12%, and 100%) on thermoelectric energy conversion and structural integrity. The engineered structure is lighter and effectively maintains the temperature gradient across the thermoelectric semiconductors, thereby resulting in higher output voltage and improved heating and cooling performance. Furthermore, these thermoelectric generators show remarkable damage tolerance, remaining fully functional even after multiple punctures and 2000 stretching cycles at 50% strain. When integrated with a 3D‐printed heatsink, they can power wearable sensors, charge batteries, and illuminate LEDs by scavenging body heat at room temperature, demonstrating their application as self‐sustainable electronics.
more »
« less
- Award ID(s):
- 2306613
- PAR ID:
- 10538132
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Materials
- Volume:
- 36
- Issue:
- 49
- ISSN:
- 0935-9648
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Harvesting body heat using thermoelectricity provides a promising path to realizing self-powered, wearable electronics that can achieve continuous, long-term, uninterrupted health monitoring. This paper reports a flexible thermoelectric generator (TEG) that provides efficient conversion of body heat to electrical energy. The device relies on a low thermal conductivity aerogel–silicone composite that secures and thermally isolates the individual semiconductor elements that are connected in series using stretchable eutectic gallium-indium (EGaIn) liquid metal interconnects. The composite consists of aerogel particulates mixed into polydimethylsiloxane (PDMS) providing as much as 50% reduction in the thermal conductivity of the silicone elastomer. Worn on the wrist, the flexible TEGs present output power density figures approaching 35 μWcm−2at an air velocity of 1.2 ms−1, equivalent to walking speed. The results suggest that these flexible TEGs can serve as the main energy source for low-power wearable electronics.more » « less
-
Abstract Liquid crystal elastomers (LCEs) have attracted tremendous interest as actuators for soft robotics due to their mechanical and shape memory properties. However, LCE actuators typically respond to thermal stimulation through active Joule heating and passive cooling, which make them difficult to control. In this work, LCEs are combined with soft, stretchable thermoelectrics to create transducers capable of electrically controlled actuation, active cooling, and thermal‐to‐electrical energy conversion. The thermoelectric layers are composed of semiconductors embedded within a 3D printed elastomer matrix and wired together with eutectic gallium–indium (EGaIn) liquid metal interconnects. This layer is covered on both sides with LCE, which alternately heats and cools to achieve cyclical bending actuation in response to voltage‐controlled Peltier activation. Moreover, the thermoelectric layer can harvest energy from thermal gradients between the two LCE layers through the Seebeck effect, allowing for regenerative energy harvesting. As demonstrations, first, closed‐loop control of the transducer is performed to rapidly track a changing actuator position. Second, a soft robotic walker that is capable of walking toward a heat source and harvesting energy is introduced. Lastly, phototropic‐inspired autonomous deflection of the limbs toward a heat source is shown, demonstrating an additional method to increase energy recuperation efficiency for soft systems.more » « less
-
Thermoelectric materials, capable of converting temperature gradients into electrical power, have been traditionally limited by a trade‐off between thermopower and electrical conductivity. This study introduces a novel, broadly applicable approach that enhances both the spin‐driven thermopower and the thermoelectric figure‐of‐merit (zT) without compromising electrical conductivity, using temperature‐driven spin crossover. Our approach, supported by both theoretical and experimental evidence, is demonstrated through a case study of chromium doped‐manganese telluride, but is not confined to this material and can be extended to other magnetic materials. By introducing dopants to create a high crystal field and exploiting the entropy changes associated with temperature‐driven spin crossover, we achieved a significant increase in thermopower, by approximately 136 μV K−1, representing more than a 200% enhancement at elevated temperatures within the paramagnetic domain. Our exploration of the bipolar semiconducting nature of these materials reveals that suppressing bipolar magnon/paramagnon‐drag thermopower is key to understanding and utilizing spin crossover‐driven thermopower. These findings, validated by inelastic neutron scattering, X‐ray photoemission spectroscopy, thermal transport, and energy conversion measurements, shed light on crucial material design parameters. We provide a comprehensive framework that analyzes the interplay between spin entropy, hopping transport, and magnon/paramagnon lifetimes, paving the way for the development of high‐performance spin‐driven thermoelectric materials.more » « less
-
Abstract Microelectronic thermoelectric generators are one potential solution to energizing energy autonomous electronics, such as internet-of-things sensors, that must carry their own power source. However, thermoelectric generators with the mm2footprint area necessary for on-chip integration made from high thermoelectric figure-of-merit materials have been unable to produce the voltage and power levels required to run Si electronics using common temperature differences. We present microelectronic thermoelectric generators using Si0.97Ge0.03, made by standard Si processing, with high voltage and power generation densities that are comparable to or better than generators using high figure-of-merit materials. These Si-based thermoelectric generators have <1 mm2areas and can energize off-the-shelf sensor integrated circuits using temperature differences ≤25 K near room temperature. These generators can be directly integrated with Si circuits and scaled up in area to generate voltages and powers competitive with existing thermoelectric technologies, but in what should be a far more cost-effective manner.more » « less
