skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Arrayed Force Sensors Made of Paper, Elastomer, and Hydrogel Particles
This article presents a sensor for detecting the distribution of forces on a surface. The device with nine buttons consisted of an elastomer-based layer as a touch interface resting on a substrate of patterned metallized paper. The elastomer-based layer included a three-by-three array of deformable, hemispherical elements/reliefs, facing down toward an array of interdigitated capacitive sensing units on patterned metallized paper. Each hemispherical element is 20 mm in diameter and 8 mm in height. When a user applied pressure to the elastomer-based layer, the contact area between the hemispherical elements and the interdigitated capacitive sensing units increased with the deformation of the hemispherical elements. To enhance the sensitivity of the sensors, embedded particles of hydrogel in the elastomer-based layer increased the measured electrical responses. The measured capacitance increased because the effective dielectric permittivity of the hydrogel was greater than that of air. Electromechanical characterization verified that the hydrogel-filled elastomer was more sensitive to force at a low range of loads (23.4 pF/N) than elastomer alone without embedded hydrogel (3.4 pF/N), as the hydrogel reduced the effective elastic modulus of the composite material by a factor of seven. A simple demonstration suggests that the force-sensing array has the potential to contribute to wearable and soft robotic devices.  more » « less
Award ID(s):
1610933
PAR ID:
10558689
Author(s) / Creator(s):
; ; ; ; ;
Publisher / Repository:
MDPI
Date Published:
Journal Name:
Micromachines
Volume:
8
Issue:
12
ISSN:
2072-666X
Page Range / eLocation ID:
356
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; (, Advanced Intelligent Systems)
    Artificial smart skins that integrate sensing and adaptiveness present a novel platform in wearable electronics on epidermis or next‐generation robotics. Herein, a highly sensitive capacitive touch senor based on a self‐conformable bi‐stable electroactive polymer (BSEP) is developed. The device combines the properties of conformable polymers and touch sensors, which grants the sensor the ability to conform to the shape of various surfaces and in different working conditions. A spray‐coated silver nanowire (AgNW) is selected as the sensor electrode for high‐resolution patterning. The unique antenna‐shaped electrode pattern results in a capacitance change of 31% when in contact with ground at a baseline of 0.13 pF. The BSEP provides stiffness tunability via an embedded compliant heater. The heater combines interdigitated silver with carbon nanotubes delivering uniform and highly efficient heating to create a tunable device with stiffness between 100s of MPa and tens of kPa, providing a large working flexibility. The efficient resistive heater provides uniform and stable heating over an area of 40 by 40 mm with a rate of 48 °C min−1at an input voltage as low as 7 V. This research merges intelligent polymeric systems and thin film electronics advancing conformable, skin‐like functional electronics. 
    more » « less
  2. ; ; ; (, Micromachines)
    null (Ed.)
    Direct fabrication of a three-dimensional (3D) structure using soft materials has been challenging. The hybrid bilayer is a promising approach to address this challenge because of its programable shape-transformation ability when responding to various stimuli. The goals of this study are to experimentally and theoretically establish a rational design principle of a hydrogel/elastomer bilayer system and further optimize the programed 3D structures that can serve as substrates for multi-electrode arrays. The hydrogel/elastomer bilayer consists of a hygroscopic polyacrylamide (PAAm) layer cofacially laminated with a water-insensitive polydimethylsiloxane (PDMS) layer. The asymmetric volume change in the PAAm hydrogel can bend the bilayer into a curvature. We manipulate the initial monomer concentrations of the pre-gel solutions of PAAm to experimentally and theoretically investigate the effect of intrinsic mechanical properties of the hydrogel on the resulting curvature. By using the obtained results as a design guideline, we demonstrated stimuli-responsive transformation of a PAAm/PDMS flower-shaped bilayer from a flat bilayer film to a curved 3D structure that can serve as a substrate for a wide-field retinal electrode array. 
    more » « less
  3. ; (, PLOS ONE)
    Jabbari, Esmaiel (Ed.)
    This study presents novel biocompatible Polydimethylsiloxane (PDMS)-based micromechanical tweezers (μTweezers) capable of the stiffness characterization and manipulation of hydrogel-based organoids. The system showed great potential for complementing established mechanical characterization methods such as Atomic Force Microscopy (AFM), parallel plate compression (PPC), and nanoindentation, while significantly reducing the volume of valuable hydrogels used for testing. We achieved a volume reduction of ~0.22 μl/sample using the μTweezers vs. ~157 μl/sample using the PPC, while targeting high-throughput measurement of widely adopted micro-mesoscale (a few hundred μm-1500 μm) 3D cell cultures. The μTweezers applied and measured nano-millinewton forces through cantilever’ deflection with high linearity and tunability for different applications; the assembly is compatible with typical inverted optical microscopes and fit on standard tissue culture Petri dishes, allowing mechanical compression characterization of arrayed 3D hydrogel-based organoids in a high throughput manner. The average achievable output per group was 40 tests per hour, where 20 organoids and 20 reference images in one 35 mm petri dish were tested, illustrating efficient productivity to match the increasing demand on 3D organoids’ applications. The changes in stiffness of collagen I hydrogel organoids in four conditions were measured, with ovarian cancer cells (SKOV3) or without (control). The Young’s modulus of the control group (Control—day 0, E = 407± 146, n = 4) measured by PPC was used as a reference modulus, where the relative elastic compressive modulus of the other groups based on the stiffness measurements was also calculated (control-day 0, E = 407 Pa), (SKOV3-day 0, E = 318 Pa), (control-day 5, E = 528 Pa), and (SKOV3-day 5, E = 376 Pa). The SKOV3-embedded hydrogel-based organoids had more shrinkage and lowered moduli on day 0 and day 5 than controls, consistently, while SKOV3 embedded organoids increased in stiffness in a similar trend to the collagen I control from day 0 to day 5. The proposed method can contribute to the biomedical, biochemical, and regenerative engineering fields, where bulk mechanical characterization is of interest. The μTweezers will also provide attractive design and application concepts to soft membrane-micro 3D robotics, sensors, and actuators. 
    more » « less
  4. ; ; ; ; ; ; ; (, Small)
    Abstract Recent years have witnessed the rapid development of sustainable materials. Along this line, developing biodegradable or recyclable soft electronics is challenging yet important due to their versatile applications in biomedical devices, soft robots, and wearables. Although some degradable bulk hydrogels are directly used as the soft electronics, the sensing performances are usually limited due to the absence of distributed conducting circuits. Here, sustainable hydrogel‐based soft electronics (HSE) are reported that integrate sensing elements and patterned liquid metal (LM) in the gelatin–alginate hybrid hydrogel. The biopolymer hydrogel is transparent, robust, resilient, and recyclable. The HSE is multifunctional; it can sense strain, temperature, heart rate (electrocardiogram), and pH. The strain sensing is sufficiently sensitive to detect a human pulse. In addition, the device serves as a model system for iontophoretic drug delivery by using patterned LM as the soft conductor and electrode. Noncontact detection of nearby objects is also achieved based on electrostatic‐field‐induced voltage. The LM and biopolymer hydrogel are healable, recyclable, and degradable, favoring sustainable applications and reconstruction of the device with new functions. Such HSE with multiple functions and favorable attributes should open opportunities in next‐generation electronic skins and hydrogel machines. 
    more » « less
  5. ; ; ; ; ; ; (, Soft Science)
    Seismocardiography (SCG) is the measure of local vibrations in the chest due to heartbeats. Typically, SCG signals are measured using rigid integrated circuit (IC) accelerometers and bulky electronics. However, as alternatives, recent studies of emerging flexible sensors show promise. Here, we introduce the development of wireless soft capacitive sensors that require no battery or rigid IC components for measuring SCG signals for cardiovascular health monitoring. Both the capacitive and inductive components of the circuit are patterned with laser micromachining of a polyimide-coated copper and are encapsulated with an elastomer. The wearable soft sensor can detect small strain changes on the skin, which is wirelessly measured by examining the power reflected from the antenna at a stimulating frequency. The performance of the device is verified by comparing the fiducial points to SCG measured by a commercial accelerometer and electromyograms from a commercial electrode. Overall, the human subject study demonstrates that the fiducial points are consistent with data from commercial devices, showing the potential of the ultrathin soft sensors for ambulatory cardiovascular monitoring without bulky electronics and rigid components. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email