An official website of the United States government
A novel dislocation-density-based crystal plasticity model for nanocrystalline face-centered cubic metals is developed based on the thermally-activated mechanism of dislocations depinning from grain boundaries. Dislocations nucleated from grain boundary dislocation sources are assumed to be the primary carriers of plasticity in the nanocrystals. The evolution of the dislocation density thereby involves a competition between the nucleation of dislocations from grain boundary defect structures, such as ledges, and the absorption of dislocations into the grain boundary via diffusion processes. This model facilitates the simulation of plastic deformation in nanocrystalline metals, with consideration of the initial microstructure resulting from a particular processing method, to be computed as a direct result of dislocation-mediated plasticity only. The exclusion of grain boundary-mediated plasticity mechanisms in the formulation of the crystal plasticity model allows for the exploration of the fundamental role dislocations play in nanocrystalline plasticity. The combined effect of average grain size, grain size distribution shape, and initial dislocation density on the mechanical performance and strain-rate sensitivity are explored with the model. Further, the influence of the grain boundary diffusivity on post-yielding strain-hardening behavior is investigated to discern the impact that the choice of processing route has on the resulting deformation response of the material.
more »
« less
Dislocation avalanches in nanostructured molybdenum nanopillars
We investigate intermittent plasticity in nanopillars of nanocrystalline molybdenum based on in situ transmission electron microscopy observations. By correlating electron imaging results with the measured nanopillar mechanical response, we demonstrate that the intermittent plasticity in nanocrystalline molybdenum is largely caused by dislocation avalanches. Electron imaging further reveals three types of dislocation avalanches, from intragranular to transgranular to cross-granular avalanches. The measured strain bursts resulted from avalanches have similar magnitudes to those reported for the molybdenum single-crystal pillars, while the corresponding flow stress in nanocrystalline molybdenum is greatly enhanced by the small grain size. Statistical analysis also shows that the avalanches behavior has similar characteristic as single crystals in the mean field theory model. Together, our findings here provide critical insights into the deformation mechanisms in a nanostructured body-centered-cubic metal.
more »
« less
- Award ID(s):
- 2226495
- PAR ID:
- 10560362
- Publisher / Repository:
- AIP
- Date Published:
- Journal Name:
- Journal of Vacuum Science & Technology A
- Volume:
- 42
- Issue:
- 2
- ISSN:
- 0734-2101
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Molybdenum (Mo), which is one among the refractory metals, is a promising material with a wide variety of technological applications in microelectronics, optoelectronics, and energy conversion and storage. However, understanding the structure–property correlation and optimization at the nanoscale dimension is quite important to meet the requirements of the emerging nanoelectronics and nanophotonics. In this context, we focused our efforts to derive a comprehensive understanding of the nanoscale structure, phase, and electronic properties of nanocrystalline Mo films with variable microstructure and grain size. Molybdenum films were deposited under varying temperature (25–500 °C), which resulted in Mo films with variable grain size of 9–22 nm. The grazing incidence X-ray diffraction analyses indicate the (110) preferred growth behavior the Mo films, though there is a marked decrease in hardness and elastic modulus values. In particular, there is a sizable difference in maximum and minimum elastic modulus values; the elastic modulus decreased from ~460 to 260–280 GPa with increasing substrate temperature from 25–500 °C. The plasticity index and wear resistance index values show a dramatic change with substrate temperature and grain size. Additionally, the optical properties of the nanocrystalline Mo films evaluated by spectroscopic ellipsometry indicate a marked dependence on the growth temperature and grain size. This dependence on grain size variation was particularly notable for the refractive index where Mo films with lower grain size fell in a range between ~2.75–3.75 across the measured wavelength as opposed to the range of 1.5–2.5 for samples deposited at temperatures of 400–500 °C, where the grain size is relatively higher. The conductive atomic force microscopy (AFM) studies indicate a direct correlation with grain size variation and grain versus grain boundary conduction; the trend noted was improved electrical conductivity of the Mo films in correlation with increasing grain size. The combined ellipsometry and conductive AFM studies allowed us to optimize the structure–property correlation in nanocrystalline Mo films for application in electronics and optoelectronics.more » « less
-
Near-rigid-body grain rotation is commonly observed during grain growth, recrystallization, and plastic deformation in nanocrystalline materials. Despite decades of research, the dominant mechanisms underlying grain rotation remain enigmatic. We present direct evidence that grain rotation occurs through the motion of disconnections (line defects with step and dislocation character) along grain boundaries in platinum thin films. State-of-the-art in situ four-dimensional scanning transmission electron microscopy (4D-STEM) observations reveal the statistical correlation between grain rotation and grain growth or shrinkage. This correlation arises from shear-coupled grain boundary migration, which occurs through the motion of disconnections, as demonstrated by in situ high-angle annular dark-field STEM observations and the atomistic simulation–aided analysis. These findings provide quantitative insights into the structural dynamics of nanocrystalline materials.more » « less
-
Arrested soft materials such as gels and glasses exhibit a slow stress relaxation with a broad distribution of relaxation times in response to linear mechanical perturbations. Although this macroscopic stress relaxation is an essential feature in the application of arrested systems as structural materials, consumer products, foods, and biological materials, the microscopic origins of this relaxation remain poorly understood. Here, we elucidate the microscopic dynamics underlying the stress relaxation of such arrested soft materials under both quiescent and mechanically perturbed conditions through X-ray photon correlation spectroscopy. By studying the dynamics of a model associative gel system that undergoes dynamical arrest in the absence of aging effects, we show that the mean stress relaxation time measured from linear rheometry is directly correlated to the quiescent superdiffusive dynamics of the microscopic clusters, which are governed by a buildup of internal stresses during arrest. We also show that perturbing the system via small mechanical deformations can result in large intermittent fluctuations in the form of avalanches, which give rise to a broad non-Gaussian spectrum of relaxation modes at short times that is observed in stress relaxation measurements. These findings suggest that the linear viscoelastic stress relaxation in arrested soft materials may be governed by nonlinear phenomena involving an interplay of internal stress relaxations and perturbation-induced intermittent avalanches.more » « less
-
Modeling springback in sheet materials is challenging in aluminum alloys, especially when a complex strain path is applied. This paper presents results from pure bending experiments on AA 6016-T4 sheet material, where various plastic pre-strains were first applied prior to bending. A crystal plasticity based elasto-plastic selfconsistent (EPSC) model that includes the effect of backstress in the hardening law was used to predict final part shape after unloading. The backstress term in the model was calibrated using geometrically necessary dislocation (GND) content, measured experimentally by high resolution electron backscattered diffraction (HREBSD). The EPSC model predicted springforward angles for unstrained 1 mm AA 6016-T4 sheet with an error of 0.4% (0.3◦) in the worst case, while the J2 plasticity isotropic model overpredicted springforward angles by as much as 2.4% (2◦). For cases where uniaxial, plane-strain, and biaxial pre-strains were first imparted to the sheets before bending, the EPSC model with backstress accurately predicted the transition from springforward to springback, while the EPSC model without backstress did not. Backstress influence on model accuracy, which increased with greater pre-strain levels, appears to be correlated to the statistically stored dislocation (SSD) density computed by the model at the end of each pre-strain step.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1116/6.0003254
