An official website of the United States government
Oxidative thiosulfate leaching using Cu(II)-NH3 has been explored for both mining and recycling applications as a promising method for Au extraction. This study seeks to understand the dissolution behavior of Au from waste RAM chips using a Cu(II)-NH3-S2O3 solution. In the course of this work, bimodal leaching and Au loss were observed in a manner that we have not identified in the literature. Identification of the existence of a specific Au-Ni-Cu lamellar structure in the gold fingers from RAM chips by scanning electron microscopy and energy dispersive X-ray spectroscopy (SEM-EDS) revealed the possibility of interference between Au recovery and the existence of Cu and Ni. During leaching, the co-extraction of Ni was found to predict a negative impact on the Au recovery, as a result of chemical interactions from the Au-Ni-Cu interlayer. Decopperization as a pretreatment was found necessary to remove the pre-existing Cu and promote Au leaching. As part of the study parameters, such as Cu(II) concentration, aeration rates, thiosulfate and ammonia concentrations, particle sizes, and temperatures, were investigated. A satisfactory Au recovery of 98% was achieved using 50 mM Cu(II), 120 mL/min aeration rate, 0.5 M (NH3)2S2O3, and 0.75 M NH4OH (i.e., AT/AH ratio of 0.67) for 4 h residence time at room temperature (25 °C). However, there were several high recoveries prior to Au loss from the lixiviant. It was revealed that the main cause of lower Au recovery was due to a precipitation or cementation reaction that included a sulfur species formation. Because of the bimodal leaching, a composite response comprised of the time to Au loss and maximum recovery was developed, termed leaching proclivity, to facilitate statistical analysis. Furthermore, this study explores the interactions between Au-Ni-Cu and provides suggestions for improving Au thiosulfate leaching under the interference of co-existing metals from waste PCB materials.
more »
« less
Kinetics and Modeling of Counter-Current Leaching of Waste Random-Access Memory Chips in a Cu-NH3-SO4 System Utilizing Cu(II) as an Oxidizer
The leaching of Cu in ammoniacal solutions has proven an efficient method to recover Cu from waste printed circuit boards (WPCBs) that has used by many researchers over the last two decades. This study investigates the feasibility of a counter-current leaching circuit that would be coupled with an electrowinning (EW) cell. To accomplish this objective, the paper is divided into three parts. In Part 1, a leaching kinetic framework is developed from a set of experiments that were designed and conducted using end-of-life waste RAM chips as feed sources and Cu(II)-ammoniacal solution as the lixiviant. Various processing parameters, such as particle size, stirring rates, initial Cu(II) concentrations, and temperatures, were evaluated for their effects on the Cu recovery and the leaching rate. It was found that the particle size and initial Cu(II) concentration were the two most important factors in Cu leaching. Using a 1.2 mm particle size diameter and 40 g/L of initial Cu(II) concentration, a maximum Cu recovery of 96% was achieved. The Zhuravlev changing-concentration model was selected to develop the empirically fitted kinetic coefficients. In Part 2, kinetic data were adapted into a leaching function suitable for continuously stirred tank reactors. This was achieved via using the coefficients from the Zhuravlev model and adapting them to the Jander constant concentration model for use in the counter-current circuit model. Part 3 details the development of a counter-current circuit model based on the relevant kinetic model, and the circuit performance was modeled to provide a tool that would allow the exploration of maximum copper recovery whilst minimizing the Cu(II) reporting to electrowinning. A 4-stage counter-current circuit was modeled incorporating a feed of 35 g/L of Cu(II), achieving a 4.12 g/L Cu(II) output with 93% copper recovery.
more »
« less
- Award ID(s):
- 2044719
- PAR ID:
- 10565473
- Publisher / Repository:
- MDPI
- Date Published:
- Journal Name:
- Materials
- Volume:
- 16
- Issue:
- 18
- ISSN:
- 1996-1944
- Page Range / eLocation ID:
- 6274
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
The mechanism of atom transfer radical polymerization (ATRP) mediated by sodium dithionite (Na 2 S 2 O 4 ), with Cu II Br 2 /Me 6 TREN as catalyst (Me 6 TREN: tris[2-(dimethylamino)ethyl]amine) in ethanol/water mixtures, was investigated experimentally and by kinetic simulations. A kinetic model was proposed and the rate coefficients of the relevant reactions were measured. The kinetic model was validated by the agreement between experimental and simulated results. The results indicated that the polymerization followed the SARA ATRP mechanism, with a SO 2 ˙ − radical anion derived from Na 2 S 2 O 4 , acting as both supplemental activator (SA) of alkyl halides and reducing agent (RA) for Cu II /L to regenerate the main activator Cu I /L. This is similar to the reversible-deactivation radical polymerization (RDRP) procedure conducted in the presence of Cu 0 . The electron transfer from SO 2 ˙ − , to either Cu II Br 2 /Me 6 TREN or R–Br initiator, appears to follow an outer sphere electron transfer (OSET) process. The developed kinetic model was used to study the influence of targeted degree of polymerization, concentration of Cu II Br 2 /Me 6 TREN and solubility of Na 2 S 2 O 4 on the level of polymerization control. The presence of small amounts of water in the polymerization mixtures slightly increased the reactivity of the Cu I /L complex, but markedly increased the reactivity of sulfites.more » « less
-
An investigation has been carried out to understand the solution chemistry of the Cu-NH−-SO4−2 system, focusing on the effect of pH on the solubility of copper in the solution and maximizing the Cu(I):Cu(II) ratio. A Pourbaix diagram for the Cu-N-S system has also been created using the HSC Chemistry software for a wide range of Cu-NH3 species, unlike most other studies that focused only on Cu(NH3)42+ and Cu(NH3)52+ (Cu(II)) as the dominant species. The Pourbaix diagram demonstrated that the Cu(I) exists as Cu(NH3)2+, while the Cu(II) species are present in the system as Cu(NH3)42+ and Cu(NH3)52+, depending upon the Eh and pH of the solution. Copper precipitation was observed in the electrolyte at pH values less than 8.0, and the precipitation behavior increased as the pH became acidic. The highest Cu(I):Cu(II) ratio was observed at higher pH values of 10.05 due to the higher solubility of copper at higher alkaline pH. The maximum Cu(II) concentration can be achieved at 4.0 M NH4OH and 0.76 M (NH4)2SO4. In the case of low pH, the highest Cu(I):Cu(II) ratio obtained was 0.91 against the 4.0 M and 0.25 M concentrations of NH4OH and (NH4)2SO4, respectively. Meanwhile, at high pH, the maximum Cu(I):Cu(II) ratio was 15.11 against the 0.25 M (NH4)2SO4 and 4.0 M NH4OH. Furthermore, the low pH experiments showed the equilibrium constant (K) K < 1, and the high pH experiments demonstrated K > 1, which justified the lower and higher copper concentrations in the solution, respectively.more » « less
-
The rapidly accumulating amounts of waste electrical and electronic equipment (WEEE) is one of the biggest environmental concerns in modern societies, and this problem will be further accelerated in the future. The use of supercritical CO2 (scCO2) mixed with acids has been proposed as a greener solvent system compared to conventional cyanide and aqua regia solvents, however, the mechanisms of scCO2 in metal extraction from WEEE are still poorly understood. Thus, this study focused on the physical, structural, and chemical interactions between scCO2/acid solvents and complex layered components in waste printed circuit boards (WPCBs), one of the common WEEEs. Our study showed that the use of scCO2-based pretreatment allows faster leaching of metals including copper (Cu) in the subsequent hydrometallurgical process using H2SO4 and H2O2, while allowing gold (Au) recovery as hydrometallurgically delaminated solids. This enhancement is due to the selective leaching of Ni and unique inner porous structures created by ScCO2/acid treatment via dissolving the Ca-silicate-bearing fiberglass within the WPCB. Thus, the scCO2-based pretreatment of WPCBs shows a multifaceted green chemistry potential relating to the reduction in solvent usage and targeted recovery of Au prior to shredding or grinding that would reduce any loss or dilution of Au in the subsequent waste stream.more » « less
-
Copper (Cu) is an essential micronutrient required as a co-factor in the catalytic center of many enzymes. However, excess Cu can generate pleiotropic effects in the microbial cell. In addition, leaching of Cu from pipelines results in elevated Cu concentration in the environment, which is of public health concern. Sulfate-reducing bacteria (SRB) have been demonstrated to grow in toxic levels of Cu. However, reports on Cu toxicity towards SRB have primarily focused on the degree of toxicity and subsequent elimination. Here, Cu(II) stress-related effects on a model SRB, Desulfovibrio alaskensis G20, is reported. Cu(II) stress effects were assessed as alterations in the transcriptome through RNA-Seq at varying Cu(II) concentrations (5 µM and 15 µM). In the pairwise comparison of control vs. 5 µM Cu(II), 61.43% of genes were downregulated, and 38.57% were upregulated. In control vs. 15 µM Cu(II), 49.51% of genes were downregulated, and 50.5% were upregulated. The results indicated that the expression of inorganic ion transporters and translation machinery was massively modulated. Moreover, changes in the expression of critical biological processes such as DNA transcription and signal transduction were observed at high Cu(II) concentrations. These results will help us better understand the Cu(II) stress-response mechanism and provide avenues for future research.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.3390/ma16186274
