An official website of the United States government
his study examined six phosphonium-based room-temperature ionic liquids (PRTILs) having trihexyltetradecyl- or tributyltetradecyl-phosphonium cations with saccharinate, salicylate, or benzoate anions, and obtained a feature parameter to correlate their cationic chain length, anionic ring size, and contact angle with tribological properties. PRTILs with trihexyltetradecyl-phosphonium cations had lower coefficient of friction (COF) and wear than PRTILs with tributyltetradecyl- phosphonium cations, a trend attributed to the additional methylene groups providing lower contact angle. For either cation, PRTILs with the saccharinate anion exhibited much lower COF and wear than single-ring anions, due to the formation of a low-shear-strength-tribofilm facilitated by the double-ring structure and sulfur of saccharinate. Overall, this study revealed PRTIL interfacial mechanisms that can be used to identify anion-cation combinations with optimal tribological performance.
more »
« less
This content will become publicly available on September 1, 2026
Unveiling the Effect of Electrification on Phosphonium-Based Ionic Liquid Lubrication at Tribological Interfaces for Electric Vehicle Applications
Abstract Conventional lubricants face significant challenges in electric vehicle (EV) systems due to their low electrical conductivity and inability to mitigate tribo-electrification effects which can result in increased friction, wear, and electrical discharge damage under external electrification. Consequently, conductive lubricants like ionic liquids (ILs) have emerged as promising alternatives, offering enhanced compatibility with EV applications. This study investigated the tribological behavior of four phosphonium-based room temperature ionic liquids (PRTILs) with trihexyltetradecyl phosphonium [P6,6,6,14] or tributyltetradecyl phosphonium [P4,4,4,14] cations and saccharinate [Sacc] or benzoate [Benz] anions under electrified conditions, targeting potential EV applications. Physicochemical properties, including viscosity and ionic conductivity, were measured using a viscometer and a conductivity meter, while tribological properties were evaluated using an electrified mini-traction machine and an electrified rotary ball-on-disk setup. The results revealed that all the PRTILs exhibited superior tribological (friction and wear) performance than mineral oil with or without electrification. PRTILs with the [Sacc] anion feature a double aromatic ring structure, while those with the [Benz] anion feature a single aromatic ring structure. Under low electrification (10 mA), [P6,6,6,14][Sacc] outperformed [Benz]-based PRTILs, showing a lower coefficient of friction and wear due to their higher viscosity and lower ionic conductivity. Additionally, [P6,6,6,14][Sacc] showed a power loss lower than [P4,4,4,14][Sacc] but higher than [Benz]-based PRTILs under tribo-electrification. The addition of graphene nanoplatelets (GNPs) reduced the power loss of [P6,6,6,14][Sacc] by 24% by reducing the electric contact resistance. Overall, double-ring aromatic [P6,6,6,14][Sacc] demonstrated superior tribological performance, and GNP additives enhanced their power efficiency, offering a promising pathway for IL-based lubricant development for electrified conditions.
more »
« less
- Award ID(s):
- 2010205
- PAR ID:
- 10590898
- Publisher / Repository:
- ASME
- Date Published:
- Journal Name:
- Journal of Tribology
- Volume:
- 147
- Issue:
- 9
- ISSN:
- 0742-4787
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Although lubricants play an essential role in reducing wear and friction in mechanical systems, environmental issues persist. In the past decades, Ionic Liquids (ILs) have arisen as environmentally friendly alternatives to conventional lubricants and additives. ILs are low-volatile and non-flammable salts that possess low melting points (below 100 °C). Their tunable properties, achieved by selecting the appropriate cation and anion, make them ideal candidates for different applications, including lubricants. In recent times, Protic Ionic Liquids (PILs) have attracted attention in the tribological community as a cost-effective alternative to conventional aprotic counterparts. In this work, a choline-amino acid ionic liquid, derived only from renewable, biodegradable, and biocompatible products, was synthesized, and investigated as both neat lubricant and additive to non-polar oil. The lubricating properties of [CHO][GLY] were studied both as a neat lubricant and as a 1 wt. % additive to a polyalphaolefin (PAO) oil using a ball-on-flat reciprocating friction tester. AISI 52100 steel disks were tested against AISI 52100 steel balls using either [CHO][GLY] or the mixture of PAO+[CHO][GLY]. For comparison purposes, the commercially available base oil, PAO, was also tested. Preliminary results showed no major differences in friction between the lubricants used. Nevertheless, the addition of 1 wt.% to the PAO demonstrated a remarkable 30% reduction in wear on the steel disk. This encouraging improvement in anti-wear characteristics raises the potential advancement of lubrication technology with the choline-amino acid ionic liquid, coupled with its environmentally friendly nature. Energy-dispersive X-ray (EDX) spectroscopy, non-contact profilometry, and scanning electron microscopy (SEM) were used to study the worn steel surfaces and elucidate the wear mechanisms.more » « less
-
The friction and wear behavior of palladium (Pd)-rich amorphous alloy (Pd43Cu27Ni10P20) against 440C stainless steel under ionic liquids as lubricants, i.e., 1-nonyl-3-methylimidazolium bis[(trifluoromethane)sulfonyl]amide ([C9C1im][NTf2]), were investigated using a ball-on-disc reciprocating tribometer at ambient, 100 and 200 °C with different sliding speeds of 3 and 7 mm/s, whose results were compared to those from crystalline Pd samples. The measured coefficient of friction (COF) and wear were affected by both temperature and sliding speed. The COF of crystalline Pd samples dramatically increased when the temperature increased, whereas the COF of the amorphous Pd alloy samples remained low. As the sliding speed increased, the COF of both Pd samples showed decreasing trends. From the analysis of a 3D surface profilometer and scanning electron microscopy (SEM) with electron dispersive spectroscopy (EDS) data, three types of wear (i.e., delamination, adhesive, and abrasive wear) were observed on the crystalline Pd surfaces, whereas the amorphous Pd alloy surfaces produced abrasive wear only. In addition, X-ray photoelectron spectroscopy (XPS) measurements were performed to study the formation of tribofilm. It was found that the chemical reactivity at the contacting interface increased with temperature and sliding contact speed. The ionic liquids (ILs) were effective as lubricants when the applied temperature and sliding speed were 200 °C and 7 mm/s, respectively.more » « less
-
Ionic liquids are currently being considered as potential electrolyte candidates for next-generation batteries and energy storage devices due to their high thermal and chemical stability. However, high viscosity and low conductivity at lower temperatures have severely hampered their commercial applications. To overcome these challenges, it is necessary to develop structure–property models for ionic liquid transport properties to guide the ionic liquid design. This work expands our previous effort in developing a machine learning model on imidazolium-based ionic liquids to now include ten different cation families, representing structural and chemical diversity. The model dataset contains 2869 ionic conductivity values over a temperature range of 238–472 K collected from the NIST ILThermo database and literature values for 397 unique ionic liquids. The database covers 214 unique cations and 68 unique anions. Three machine learning models, namely multiple linear regression, random forest, and extreme gradient boosting are applied to correlate the ionic liquid conductivity data with cation and anion features. Shapely additive analysis is performed to glean insights into cation and anion features with significant impact on ionic conductivity. Finally, the extreme gradient boosting model is used to predict the ionic conductivity of ionic liquids from all the possible combinations of unique cations and anions to identify ionic liquids crossing the ionic conductivity threshold of 2.0 S m −1 .more » « less
-
Synovial joints, critical for limb biomechanics, rely on sophisticated lubrication systems to minimize wear. Disruptions, whether from injury or disease, often necessitate joint replacements. While additive manufacturing offers personalized implants, ensuring wear resistance remains a challenge. This study delves into the potential of Ti3C2Tx and Mo2TiC2Tx nanosheets in mitigating wear of additively manufactured cobalt-chromium tungsten alloy substrates when incorporated as additives into synovial fluid. The colloidal solutions demonstrate an excellent stability, a crucial factor for reproducible assays and potential clinical applicability. Analysis of contact angles and surface tensions reveals MXene-induced alterations in substrate wettability, while maintaining their general hydrophilic character. Viscosity analysis indicates that MXene addition reduces the dynamic viscosity, particularly at higher concentrations above 5 mg/mL, thus enhancing dispersion and lubrication properties. Friction and wear tests demonstrate a dependency on the MXene concentration, while Ti3C2Tx exhibits stable friction coefficients and up to 77 % wear reduction at 5 mg/mL, which was attributed to the formation of a wear-protecting tribo-film (amorphous carbon and MXene nano-sheets). Our findings suggest that Ti3C2Tx, when supplied in favorable concentrations, holds promise for reducing wear in biotribological applications, offering avenues for future research into optimizing MXene utilization in load-bearing joint replacements and other biomedical devices.more » « less
