An official website of the United States government
III-nitrides and related alloys are widely used for optoelectronics and as acoustic resonators. Ferroelectric wurtzite nitrides are of particular interest because of their potential for direct integration with Si and wide bandgap semiconductors and unique polarization switching characteristics; such interest has taken off since the first report of ferroelectric Al1−xScxN alloys. However, the coercive fields needed to switch polarization are on the order of MV/cm, which are 1–2 orders of magnitude larger than oxide perovskite ferroelectrics. Atomic-scale point defects are known to impact the dielectric properties, including breakdown fields and leakage currents, as well as ferroelectric switching. However, very little is known about the native defects and impurities in Al1−xScxN and their effect on the dielectric and ferroelectric properties. In this study, we use first-principles calculations to determine the formation energetics of native defects and unintentional oxygen incorporation and their effects on the polarization switching barriers in Al1−xScxN alloys. We find that nitrogen vacancies are the dominant native defects, and unintentional oxygen incorporation on the nitrogen site is present in high concentrations. They introduce multiple mid-gap states that can lead to premature dielectric breakdown and increased temperature-activated leakage currents in ferroelectrics. We also find that nitrogen vacancy and substitutional oxygen reduce the switching barrier in Al1−xScxN at low Sc compositions. The effect is minimal or even negative (increases barrier) at higher Sc compositions. Unintentional defects are generally considered to adversely affect ferroelectric properties, but our findings reveal that controlled introduction of point defects by tuning synthesis conditions can instead benefit polarization switching in ferroelectric Al1−xScxN at certain compositions.
more »
« less
A phenomenological thermodynamic energy density function for ferroelectric wurtzite Al1−xScxN single crystals
A Landau–Devonshire thermodynamic energy density function for ferroelectric wurtzite aluminum scandium nitride (Al1−xScxN) solid solution is developed. It is parametrized using available experimental and theoretical data, enabling the accurate reproduction of composition-dependent ferroelectric properties, such as spontaneous polarization, dielectric permittivity, and piezoelectric constants, for both bulk and thin films. The maximum concentration of Sc for the wurtzite structure to remain ferroelectric is found to be 61 at. %. A detailed analysis of Al1−xScxN thin films reveals that the ferroelectric phase transition and properties are insensitive to substrate strain. This study lays the foundation for quantitative modeling of novel ferroelectric wurtzite solid solutions.
more »
« less
- Award ID(s):
- 2133373
- PAR ID:
- 10593908
- Publisher / Repository:
- American Institute of Physics
- Date Published:
- Journal Name:
- Journal of Applied Physics
- Volume:
- 135
- Issue:
- 9
- ISSN:
- 0021-8979
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
We present a thermodynamic analysis of the recently discovered nitride ferroelectric materials using the classic Landau–Devonshire approach. Electrostrictive and dielectric stiffness coefficients of Al1−xScxN with a wurtzite structure (6 mm) are determined using a free energy density function assuming a hexagonal parent phase (6/mmm), with the first-order phase transition based on the dielectric stiffness relationships. The results of this analysis show that the strain sensitivity of the energy barrier is one order of magnitude larger than that of the spontaneous polarization in these wurtzite ferroelectrics, yet both are less sensitive to strain compared to classic perovskite ferroelectrics. These analysis results reported here explain experimentally reported sensitivity of the coercive field to elastic strain/stress in Al1−xScxN films and would enable further thermodynamic analysis via phase field simulation and related methods.more » « less
-
Ferroelectric Al1−xScxN has raised much interest in recent years due to its unique ferroelectric properties and complementary metal oxide semiconductor back-end-of-line compatible processing temperatures. Potential applications in embedded nonvolatile memory, however, require ferroelectric materials to switch at relatively low voltages. One approach to achieving a lower switching voltage is to significantly reduce the Al1−xScxN thickness. In this work, ferroelectric behavior in 5–27 nm films of sputter deposited Al0.72Sc0.28N has been studied. We find that the 10 kHz normalized coercive field increases from 4.4 to 7.3 MV/cm when reducing the film thickness from 27.1 to 5.4 nm, while over the same thickness range, the characteristic breakdown field of a 12.5 μm radius capacitor increases from 8.3 to 12.1 MV/cm. The 5.4 nm film demonstrates ferroelectric switching at 5.5 V when excited with a 500 ns pulse and a switching speed of 60 ns.more » « less
-
Thin film through-thickness stress gradients produce out-of-plane bending in released microelectromechanical systems (MEMS) structures. We study the stress and stress gradient of Al0.68Sc0.32N thin films deposited directly on Si. We show that Al0.68Sc0.32N cantilever structures realized in films with low average film stress have significant out-of-plane bending when the Al1−xScxN material is deposited under constant sputtering conditions. We demonstrate a method where the total process gas flow is varied during the deposition to compensate for the native through-thickness stress gradient in sputtered Al1−xScxN thin films. This method is utilized to reduce the out-of-plane bending of 200 µm long, 500 nm thick Al0.68Sc0.32N MEMS cantilevers from greater than 128 µm to less than 3 µm.more » « less
-
Silicon photonics has enabled large-scale production of integrated optical devices for a vast array of applications. However, extending its use to nonlinear devices is difficult since silicon does not exhibit an intrinsic second-order nonlinearity. While heterogeneous integration of strongly nonlinear materials is possible, it often requires additional procedures since these materials cannot be directly grown on silicon. On the other hand, CMOS-compatible materials often suffer from weaker nonlinearities, compromising efficiency. A promising alternative to current material platforms is scandium-doped aluminum nitride (Al1−xScxN), which maintains the CMOS compatibility of aluminum nitride (AlN) and has been used in electrical devices for its enhanced piezoelectricity. Here, we observe enhancement in optical second-order susceptibility (χ(2)) in CMOS-compatible Al1−xScxN thin films with varying Sc concentrations. For Al0.64Sc0.36N, the χ(2) component d33 is enhanced to 62.3 ± 5.6 pm/V, which is 12 times stronger than intrinsic AlN and twice as strong as lithium niobate. Increasing the Sc concentration enhances both χ(2) components, but loss increases with a higher Sc concentration as well, with Al0.64Sc0.36N exhibiting 17.2 dB/cm propagation loss at 1550 nm and Al0.80Sc0.20N exhibiting 8.2 dB/cm at 1550 nm. Since other material properties of this alloy are also affected by Sc, tuning the Sc concentration can balance strong nonlinearity, loss, and other factors depending on the needs of specific applications. As such, Al1−xScxN could facilitate low cost development of nonlinear integrated photonic devices.more » « less
