An official website of the United States government
Abstract Pulsed dielectric barrier discharges (DBD) in He–H 2 O and He–H 2 O–O 2 mixtures are studied in near atmospheric conditions using temporally and spatially resolved quantitative 2D imaging of the hydroxyl radical (OH) and hydrogen peroxide (H 2 O 2 ). The primary goal was to detect and quantify the production of these strongly oxidative species in water-laden helium discharges in a DBD jet configuration, which is of interest for biomedical applications such as disinfection of surfaces and treatment of biological samples. Hydroxyl profiles are obtained by laser-induced fluorescence (LIF) measurements using 282 nm laser excitation. Hydrogen peroxide profiles are measured by photo-fragmentation LIF (PF-LIF), which involves photo-dissociating H 2 O 2 into OH with a 212.8 nm laser sheet and detecting the OH fragments by LIF. The H 2 O 2 profiles are calibrated by measuring PF-LIF profiles in a reference mixture of He seeded with a known amount of H 2 O 2 . OH profiles are calibrated by measuring OH-radical decay times and comparing these with predictions from a chemical kinetics model. Two different burst discharge modes with five and ten pulses per burst are studied, both with a burst repetition rate of 50 Hz. In both cases, dynamics of OH and H 2 O 2 distributions in the afterglow of the discharge are investigated. Gas temperatures determined from the OH-LIF spectra indicate that gas heating due to the plasma is insignificant. The addition of 5% O 2 in the He admixture decreases the OH densities and increases the H 2 O 2 densities. The increased coupled energy in the ten-pulse discharge increases OH and H 2 O 2 mole fractions, except for the H 2 O 2 in the He–H 2 O–O 2 mixture which is relatively insensitive to the additional pulses.
more »
« less
Managing photon flux in a miniaturized photoionization detector
Miniaturized photoionization detectors (PIDs) are used in conjunction with gas chromatography systems to detect volatile compounds in gases by collecting the current from the photoionized gas analytes. PIDs should be inexpensive and compatible with a wide range of analyte species. One such PID is based on the formation of a He plasma in a dielectric barrier discharge (DBD), which generates vacuum UV (VUV) photons from excited states of He to photoionize gas analytes. There are several design parameters that can be leveraged to increase the ionizing photon flux to gas analytes to increase the sensitivity of the PID. To that end, the methods to maximize the photon flux from a pulsed He plasma in a DBD-PID were investigated using a two-dimensional plasma hydrodynamics model. The ionizing photon flux originated from the resonance states of helium, He(3P) and He(21P), and from the dimer excimer He2*. While the photon flux from the resonant states was modulated over the voltage pulse, the photon flux from He2* persisted long after the voltage pulse passed. Several geometrical optimizations were investigated, such as using an array of pointed electrodes. However, increasing the capacitance of the dielectric enclosing the plasma chamber had the largest effect on increasing the VUV photon fluence to gas analytes.
more »
« less
- Award ID(s):
- 2032604
- PAR ID:
- 10594038
- Publisher / Repository:
- American Institute of Physics
- Date Published:
- Journal Name:
- Journal of Applied Physics
- Volume:
- 135
- Issue:
- 14
- ISSN:
- 0021-8979
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Dielectric barrier discharge (DBD) plasma is a promising technology for catalysis due to its low‐temperature operation, cost‐effectiveness, and silent operation. This review comprehensively analyzes the design and operational parameters of DBD plasma reactors for three key catalytic applications: CH4conversion, CO2splitting, and dry reforming of methane (DRM). While catalyst selection is crucial for achieving desired product selectivity, reactor design and reaction parameters such as discharge power, electrode gap, reactor length, frequency, dielectric material thickness, and feed gas flow rate, significantly influence discharge characteristics and reaction mechanisms. This review also explores the influence of less prominent factors, such as electrode shape and applied voltage waveforms. Additionally, this review addresses the challenges of DBD plasma catalysis, including heat loss, temperature effects on discharge characteristics, and strategies for enhancing overall efficiency.more » « less
-
Activation of liquids with atmospheric pressure plasmas is being investigated for envi-ronmental and biomedical applications. When activating the liquid using gas plasma produced species (as opposed to plasmas sustained in the liquid), a rate limiting step is transport of these species into the liquid. To first order, the efficiency of activating the liquid is improved by in-creasing the ratio of the surface area of the water in contact with the plasma compared to its vol-ume – often called the surface-to-volume ratio (SVR). Maximizing the SVR then motivates the plasma treatment of thin films of liquids. In this paper, results are discussed from a computa-tional investigation using a global model of atmospheric pressure plasma treatment of thin water films by a dielectric barrier discharge (DBD) sustained in different gases (Ar, He, air, N2, O2). The densities of reactive species in the plasma activated water (PAW) are evaluated. The resi-dence time of the water in contact with the plasma is increased by recirculating the PAW in plasma reactor. Longer lived species such as H2O2aq and NO3−aq accumulate over time (aq de-notes an aqueous species). DBDs sustained in Ar and He are the most efficient at producing H2O2aq, DBDs sustained in argon produces the largest density of NO3−aq with the lowest pH, and discharges sustained in O2 and air produce the highest densities of O3aq. Comparisons to experi-ments by others show agreement in the trends in densities in PAW including O3aq, OHaq, H2O2aq and NO3−aq, and highlight the importance of controlling desolvation of species from the activated water.more » « less
-
Abstract This study reports an experimental comparison of two types of atmospheric pressure plasma jets in terms of their fundamental plasma characteristics and efficacy in bacterial sterilization. The plasma jets are fabricated by inserting a high voltage electrode inside a one-end closed (double DBD plasma jet) or both ends open (single DBD plasma jet) quartz tubes which are further enclosed inside a second quartz tube containing a ground electrode. Both plasma jets are operated in contact with water surface by using a unipolar pulsed DC power supply with helium as the working gas. Results from electrical and time-resolved imaging show that the single DBD configuration induces 3–4 times higher accumulation of charges onto the water surface with significantly faster propagation of plasma bullets. These results are accompanied by the higher discharge intensity as well as stronger emissions from short-lived reactive species which were analyzed through optical emission spectroscopy at the plasma-water interface. The rotational temperature for the single DBD configuration was observed to be higher making it unsafe for direct treatments of sensitive biological targets. These characteristics of the single DBD configuration result in the production of more than two times higher concentration of H 2 O 2 in plasma activated water. Shielding of the HV electrode reduces the plasma potential which in turn reduces the electric field & electron energy at the plasma-water interface. The reduced electric field for the double DBD configuration was lower by ≈463 Td than the single DBD configuration. The bactericidal efficacy of the two configurations of the plasma jets were tested against Escherichia coli , a well studied Gram-negative bacterium that can be commensal and pathogenic in human body. Our results demonstrate that although single DBD plasma jet result in stronger antibacterial effects, the double DBD configuration could be safer.more » « less
-
Objective: Persistent Identifiers (PIDs) are central to the vision of open science described in the FAIR Principles. However, the use of PIDs for scientific instruments and facilities is decentralized and fragmented. This project aims to develop community-based standards, guidelines, and best practices for how and why PIDs can be assigned to facilities and instruments. Methods: We hosted several online and in-person focus groups and discussions, cumulating in a two-day in-person workshop featuring stakeholders from a variety of organizations and disciplines, such as instrument and facilities operators, PID infrastructure providers, researchers who use instruments and facilities, journal publishers, university administrators, federal funding agencies, and information and data professionals. Results: Our first-year efforts resulted in four main areas of interest: developing a better understanding of the current PID ecosystem; clarifying how and when PIDs could be assigned to scientific instruments and facilities; challenges and barriers involved with assigning PIDs; incentives for researchers, facility managers, and other stakeholders to encourage the use of PIDs. Conclusions: The potential for PIDs to facilitate the discovery, connection, and attribution of research instruments and facilities indicates an obvious value in their use. The lack of standards of how and when they are created, assigned, updated, and used is a major barrier to their widespread use. Data and information professionals can work to create relationships with stakeholders, provide relevant education and outreach activities, and integrate PIDs for instruments and facilities into their data curation and publication workflows.more » « less
