An official website of the United States government
This study investigates seismically-induced failure mechanisms in massive rock slopes using the bonded particle model. The data from this study can be used to track seismically-induced stresses in steep slope geometries leading up to failure initiation. The data can also be used to study the propagation of damage initiated by these failure mechanisms and track the development of mass movement enabled by the seismically-induced damage. The bonded particle model data includes the motion time-histories of an array of monitoring particles in the slope, the stress tensors of representative volume elements throughout loading, and the full model geometry, which can be used to reproduce the discrete element model.
more »
« less
This content will become publicly available on June 1, 2026
Seismically-induced failure mechanisms in massive rock slopes
This article presents a study of seismically-induced failure of massive steep rock slopes. A dynamic implementation of the bonded particle model (BPM) for rock is used to simulate the dynamic response and initiation of fracture in the slopes. Observation of forces that develop within the model in response to wave transmission and dynamic excitation provides insight into the fundamental mechanisms at work in seismically induced rock slope failure. Five distinct mechanisms of failure initiation are identified using non-destructive simulations and confirmed with destructive simulations. Three distinct modes of rock mass movement enabled by the failure mechanisms are identified. The predominant co-seismic failure mode was a shallow, highly-disrupted cliff collapse. Cliff collapse is initiated by relatively low levels of shaking. Shallow failures are also triggered at higher levels of shaking prior to the initiation of deeper, more coherent failures in the same seismic event. The results of the numerical study agree with qualitative historical surveys of seismically-induced rock slope failure trends and provide insight into the mechanisms behind observed co-seismic rock slope behavior. The frequently observed shallow failures are triggered by high compression stresses near the cliff toe combined with shallow subhorizontal ruptures behind the cliff face. These mechanisms are not well-captured by simplified analysis methods which may lead to underprediction of shallow co-seismic events. Deeper failure surfaces from stronger shaking create a base-isolation effect, slowing further disruption in the failure mass. Slope dynamic response and damage accumulation were shown to be interdependent and complex, emphasizing the importance of further research into the interaction between rock mass strength, slope geometry, structure, and ground motion characteristics.
more »
« less
- Award ID(s):
- 2301519
- PAR ID:
- 10625727
- Publisher / Repository:
- Elsevier
- Date Published:
- Journal Name:
- Engineering Geology
- Volume:
- 352
- Issue:
- C
- ISSN:
- 0013-7952
- Page Range / eLocation ID:
- 108046
- Subject(s) / Keyword(s):
- Rock slope failure Earthquake engineering Discrete element model failure mechanisms
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Submarine slope failures pose risks to coastlines because they can damage infrastructure and generate tsunamis. Passive margin slope failures represent the largest mass failures on Earth, yet we know little about their dynamics. While numerous studies characterize the lithology, structure, seismic attributes and geometry of failure deposits, we lack direct observations of failure evolution. Thus, we lack insight into the relationships between initial conditions, slope failure initiation and evolution, and final deposits. To investigate submarine slope failure dynamics in relation to initial conditions and to observe failure processes we performed physical experiments in a benchtop flume and produced numerical models. Submarine slope failures were induced under controlled pore pressure within sand–clay mixtures (0–5 wt% clay). Increased clay content corresponded to increased cohesion and pore pressure required for failure. Subsurface fractures and tensile cracks were only generated in experiments containing clay. Falling head tests showed a log-linear relation between hydraulic conductivity and clay content, which we used in our numerical models. Models of our experiments effectively simulate overpressure (pressure in excess of hydrostatic) and failure potential for (non)cohesive sediment mixtures. Overall our work shows the importance of clay in reducing permeability and increasing cohesion to create different failure modes due to overpressure.more » « less
-
Abstract Ambient vibration measurements can detect resonance frequency changes related to rock slope instability damage or boundary condition changes during progressive failure. However, the impact of slope kinematics on resonance changes and the expected form and sensitivity of frequency evolution during destabilization require clarification to improve the implementation of this technique across diverse settings. Since instrumented rock slope failures are rare, numerical modeling is needed to study the anticipated spectral response from in situ monitoring. We used 2D distinct‐element modeling to evaluate the sensitivity and evolution of rock slope resonance behavior for slab toppling, flexural toppling, and planar sliding instabilities during progressive failure. Model simulations revealed that fundamental resonance frequency decreases between 20% and 60% with changes correlated with increasing length of open joints. Changes to higher‐order frequencies associated with landslide sub‐volumes were also detectable for cases with multiple fracture networks. Resonance behavior was most pronounced for failures dominated by steeply dipping open tension cracks, that is, flexural and slab toppling. Additionally, amplification patterns across the slope varied for the flexural toppling and sliding cases, providing potential new information with which to characterize landslide failure mechanisms using ambient vibration array measurements. Our results demonstrate landslide characteristics well‐suited for in situ ambient resonance monitoring and provide new data describing the anticipated changes in resonance frequencies during progressive rock slope failure.more » « less
-
The subject of the influence of the seismic excitation on limit loads of footings is revisited, with emphasis on the moment load. The kinematic approach of limit analysis is employed using two collapse mechanisms allowing footing rotation and one with pure translational kinematics. Two of the mechanisms have novel elements, not presented in earlier literature. The paper is focused on the resistance of the soil weight to activating a mechanism of failure, which can be best cast in terms of the seismic bearing capacity factor Nsγ . Seismic loads from the superstructure are interpreted as those caused by a three-mass model, each mass with its own seismic coefficient. The notion of generalized loads is used to present the yield locus for the footing in terms of the gravity force, horizontal force, and moment. The non-symmetric components of the load are interpreted as seismically activated. The approach yields a strict upper bound to the magnitude of the load vector causing failure. Of the three failure mechanisms considered none yields the best (least) solutions for all combinations of loads. In general, the two mechanisms with footing rotation perform better for large moments, whereas the translational mechanism yields better results when moments are small. However, even in the absence of a moment load, the rotational mechanism can yield better estimates of the limit load when the seismic coefficient is relatively large.more » « less
-
Abstract Wildfire records demonstrate worsening patterns coupled with the spread to higher altitudes in several regions, raising the risk of post‐wildfire ground failures. This study investigates the post‐wildfire stability of unsaturated hillslopes against rainfall‐triggered shallow landslides. We developed a new physics‐based analytical framework incorporating wildfire‐induced changes in soil properties and near‐surface processes affecting the hillslope stability. A coupled hydromechanical infiltration model is integrated into an infinite slope stability analysis to simulate temporal changes in the depth profiles of soil water content, pressure head, and the resulting factor of safety (F.S.) of a vegetated slope. We consider the antecedent conditions of soil and vegetation cover, including the recovery phase after the fire, wildfire‐induced alterations in transpiration, and time‐varying infiltration rates. The model is verified against numerical simulations and employed in parametric studies evaluating the effects of wildfire severity and rainfall intensity‐duration. For the cases examined, it was shown that wildfire could reduce the F.S. of slopes by 25%. As a case study, the model successfully captured shallow rainfall‐triggered landslides that occurred in the Las Lomas watershed in California, USA, in 2019, 3 years after the Fish Fire burned the area. The proposed model uses measurable hillslope and wildfire characteristics and can be employed to evaluate the risk of shallow landslides in wildfire‐prone areas.more » « less
