skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Scalable Programming of LaAlO 3 /SrTiO 3 Interfaces via Ultra‐Low‐Voltage Electron‐Beam Lithography
Abstract Interface engineering at complex oxide heterostructures enables a wide range of electronic functionalities critical for next‐generation devices. Here it is demonstrated that ultra‐low‐voltage electron beam lithography (ULV‐EBL) creates high‐quality mesoscale structures at LaAlO3/SrTiO3(LAO/STO) interfaces with greater efficiency than conventional methods. Nanowires, tunnel barriers, and electron waveguides are successfully patterned that exhibit distinctive transport characteristics including 1D superconductivity, nonlinear current–voltage behavior, and ballistic electron flow. While conductive atomic force microscopy (c‐AFM) previously enabled similar interface modifications, ULV‐EBL provides significantly faster patterning speeds (10 mm s−1vs 1 µm s−1), wafer‐scale capability (>(10 cm)2vs <(90 µm)2), and maintenance of pattern quality under vacuum conditions. Additionally, an efficient oxygen plasma treatment method is developed for pattern erasure and surface cleaning, which reveals novel surface reaction dynamics at oxide interfaces. These capabilities establish ULV‐EBL as a versatile approach for scalable interface engineering in complex oxide heterostructures, with potential applications in reconfigurable electronics, sensors, and oxide‐based devices.  more » « less
Award ID(s):
2225888
PAR ID:
10651815
Author(s) / Creator(s):
 ;  ;  ;  ;  ;  ;  ;  
Publisher / Repository:
Wiley
Date Published:
Journal Name:
Advanced Materials Interfaces
Volume:
12
Issue:
21
ISSN:
2196-7350
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; ; ; ; ; ; ; et al (, Science Advances)
    Charge transfer or redistribution at oxide heterointerfaces is a critical phenomenon, often leading to remarkable properties such as two-dimensional electron gas and interfacial ferromagnetism. Despite studies on LaNiO3/LaFeO3superlattices and heterostructures, the direction and magnitude of the charge transfer remain debated, with some suggesting no charge transfer due to the high stability of Fe3+(3d5). Here, we synthesized a series of epitaxial LaNiO3/LaFeO3superlattices and demonstrated partial (up to ~0.5 e−/interface unit cell) charge transfer from Fe to Ni near the interface, supported by density functional theory simulations and spectroscopic evidence of changes in Ni and Fe oxidation states. The electron transfer from LaFeO3to LaNiO3and the subsequent rearrangement of the Fe 3d band create an unexpected metallic ground state within the LaFeO3layer, strongly influencing the in-plane transport properties across the superlattice. Moreover, we establish a direct correlation between interfacial charge transfer and in-plane electrical transport properties, providing insights for designing functional oxide heterostructures with emerging properties. 
    more » « less
  2. ; ; ; ; ; ; ; ; ; ; et al (, Science Advances)
    KTaO3heterostructures have recently attracted attention as model systems to study the interplay of quantum paraelectricity, spin-orbit coupling, and superconductivity. However, the high and low vapor pressures of potassium and tantalum present processing challenges to creating heterostructure interfaces clean enough to reveal the intrinsic quantum properties. Here, we report superconducting heterostructures based on high-quality epitaxial (111) KTaO3thin films using an adsorption-controlled hybrid PLD to overcome the vapor pressure mismatch. Electrical and structural characterizations reveal that the higher-quality heterostructure interface between amorphous LaAlO3and KTaO3thin films supports a two-dimensional electron gas with substantially higher electron mobility, superconducting transition temperature, and critical current density than that in bulk single-crystal KTaO3-based heterostructures. Our hybrid approach may enable epitaxial growth of other alkali metal–based oxides that lie beyond the capabilities of conventional methods. 
    more » « less
  3. ; ; ; ; ; ; ; ; (, Advanced Materials)
    Abstract A synaptic memristor using 2D ferroelectric junctions is a promising candidate for future neuromorphic computing with ultra‐low power consumption, parallel computing, and adaptive scalable computing technologies. However, its utilization is restricted due to the limited operational voltage memory window and low on/off current (ION/OFF) ratio of the memristor devices. Here, it is demonstrated that synaptic operations of 2D In2Se3ferroelectric junctions in a planar memristor architecture can reach a voltage memory window as high as 16 V (±8 V) and ION/OFFratio of 108, significantly higher than the current literature values. The power consumption is 10−5 W at the on state, demonstrating low power usage while maintaining a large ION/OFFratio of 108compared to other ferroelectric devices. Moreover, the developed ferroelectric junction mimicked synaptic plasticity through pulses in the pre‐synapse. The nonlinearity factors are obtained 1.25 for LTP, −0.25 for LTD, respectively. The single‐layer perceptron (SLP) and convolutional neural network (CNN) on‐chip training results in an accuracy of up to 90%, compared to the 91% in an ideal synapse device. Furthermore, the incorporation of a 3 nm thick SiO2interface between the α‐In2Se3and the Au electrode resulted in ultrahigh performance among other 2D ferroelectric junction devices to date. 
    more » « less
  4. ; ; ; ; ; ; ; ; ; ; et al (, Small Methods)
    Abstract Complex oxide thin films cover a range of physical properties and multifunctionalities that are critical for logic, memory, and optical devices. Typically, the high‐quality epitaxial growth of these complex oxide thin films requires single crystalline oxide substrates such as SrTiO3(STO), MgO, LaAlO3, a‐Al2O3,and many others. Recent successes in transferring these complex oxides as free‐standing films not only offer great opportunities in integrating complex oxides on other devices, but also present enormous opportunities in recycling the deposited substrates after transfer for cost‐effective and sustainable processing of complex oxide thin films. In this work, the surface modification effects introduced on the recycled STO are investigated, and their impacts on the microstructure and properties of subsequently grown epitaxial oxide thin films are assessed and compared with those grown on the pristine substrates. Detailed analyses using high‐resolution scanning transmission electron microscopy and geometric phase analysis demonstrate distinct strain states on the surfaces of the recycled STO versus the pristine substrates, suggesting a pre‐strain state in the recycled STO substrates due to the previous deposition layer. These findings offer opportunities in growing highly mismatched oxide films on the recycled STO substrates with enhanced physical properties. Specifically, yttrium iron garnet (Y3Fe5O12) films grown on recycled STO present different ferromagnetic responses compared to that on the pristine substrates, underscoring the effects of surface modification. The study demonstrates the feasibility of reuse and redeposition using recycled substrates. Via careful handling and preparation, high‐quality epitaxial thin films can be grown on recycled substrates with comparable or even better structural and physical properties toward sustainable process of complex oxide devices. 
    more » « less
  5. ; ; ; ; (, Advanced Functional Materials)
    Abstract Ultrathin 2D metal oxides are a high‐performance class of transparent conducting materials capable of overcoming the traditional limitations of inorganic flexible electronics. The low temperature, thermodynamically favorable synthesis of 2D oxides at liquid metal interfaces offers the potential for printing these materials over large areas at unprecedented speeds with sub‐nanometer scale precision. However, these native oxides are sub‐stoichiometric and highly conductive, so new strategies are needed that can precisely engineer the electrostatics and enhance stability. In this work, the crystalline vs. amorphous phase of 2D oxides is engineered via alloying of ternary In1‐ySnyOxand ultralow deposition temperatures (120–160 °C) are afforded by In‐Sn eutectics. This approach is extended to rapid assembly of nanoscale (3–5 nm per layer) vertical 2D homojunctions with electrostatically favorable grading from high density of states front channels to lower density of states back‐channels. Detailed materials characterization reveals how this platform enhances electron mobility while improving resilience under bias‐stress in metal oxide transistors. Devices based on amorphous 2D oxide homojunctions with high‐k sol‐gel ZrOxdielectrics achieve excellent electron mobility (30 cm2/V·s), steep switching (SS of 100 mV dec−1), Ion/offof 107and 10X reduced bias‐stress shifts, presenting an ideal strategy for high‐performance flexible oxide electronics. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Text Encoded Conversion
  • XML
  • Save / Share this Record
  • Send to Email