An official website of the United States government
Membrane‐aerated biofilm reactors (MABRs) are being increasingly being implemented at full‐scale for domestic wastewater treatment and effective biofilm control is critical to their performance. This study investigated the impact of three biofilm scouring strategies on nitrogen removal performance of a pilot‐scale MABR operated in Houston, TX: (1) regular air scouring, (2) high intensity air scouring, and (3) high liquid flow scouring. Normal and high intensity air scouring regimes and a high liquid flow scour (10× baseline flow) were each tested sequentially. High NH4+‐N removal efficiency of 52% in flow‐through mode was observed post‐high liquid flow scouring, which was comparable to the performance during the intense scouring regime. The absolute abundance ofamoAgene for ammonia oxidizing bacteria (AOB) increased significantly by over 200%, between pre‐ and post‐high liquid flow scouring. The energy consumption was 43% lower for the combination of high liquid flow scouring with regular air scouring as compared to the intense air scouring. This study showed that high liquid flows may be utilized as an energy‐efficient biofilm control strategy in nitrifying MABR systems. Practitioner PointsPilot‐scale MABR reactors were operated with different scouring settings: regular aeration, intense aeration, and high liquid flow.High liquid flow scouring improved nitrification efficiency, comparable to intense scouring.High liquid flow scouring selected for nitrifiers as seen by an increase in AOB quantified asamoAgene abundance.Using high liquid flow with regular aeration scouring reduces electrical energy consumption by 43% as compared to intense aeration scouring.High liquid flows may be used as an energy‐efficient biofilm control strategy to improve nitrification performance in MABR systems.
more »
« less
This content will become publicly available on August 19, 2026
Liquid transport strategies in wearable and implantable microfluidic systems
Liquid transport is an essential functionality in microfluidic operation. This review summarizes emerging strategies for liquid management in bioelectronics, with a focus on system-level integration and applications.
more »
« less
- Award ID(s):
- 2223387
- PAR ID:
- 10653671
- Publisher / Repository:
- RSC
- Date Published:
- Journal Name:
- Lab on a Chip
- Volume:
- 25
- Issue:
- 17
- ISSN:
- 1473-0197
- Page Range / eLocation ID:
- 4252 to 4272
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Liquid metal composites are promising soft conductors for applications in soft electronics, sensors, and soft robotics. Existing liquid metal composites usually have a high‐volume fraction of liquid metal, which not only increases the density but also the material cost. Future applications in soft electronics and robotics highly demand liquid metal composites with low density and high conductivity for large‐scale, low‐cost, lightweight, and more sustainable applications. In this work, lightweight and highly conductive composites embedded with liquid metal fiber networks are synthesized. This new paradigm of liquid metal composites consists of an interconnected liquid metal fiber network embedded in a compliant rubber matrix. The liquid metal fiber network serves as an ultra‐lightweight conductive pathway for electrons. Experiments indicate that this soft conductive composite also possesses nearly strain‐insensitive conductance and superior cyclic stability. Potential applications of the composite films as stretchable interconnects, electrodes, and sensors are demonstrated.more » « less
-
Liquid metal fibers are increasingly used in soft multifunctional materials and soft electronics due to their superb stretchability, high conductivity, and lightweight. This work presents a systematic study of the electrospinning process of liquid metal microfibers. Compared to other methods that usually produce fibers thicker than 100 μm, electrospinning is a facile and low‐cost method of producing liquid metal fibers in the range of 10–100 μm. Specifically, core‐sheath liquid metal microfibers are fabricated with a highly conductive liquid metal core and a super‐stretchable thermoplastic elastomer sheath. This manufacturing process uses a liquid metal emulsion as the core solution, which circumvents manufacturing failures caused by the high surface tension of liquid metals. The influence of key processing parameters such as core flow rate, sheath flow rate, and applied voltage on the fiber diameter and morphology is studied by experiments. The mechanical and electrical properties of the as‐fabricated liquid metal microfibers, mats, and yarns are tested and discussed.more » « less
-
Abstract Liquid aerosols are ubiquitous in nature, and several tools exist to quantify their physicochemical properties. As a measurement science technique, electrochemistry has not played a large role in aerosol analysis because electrochemistry in air is rather difficult. Here, a remarkably simple method is demonstrated to capture and electroanalyze single liquid aerosol particles with radii on the order of single micrometers. An electrochemical cell is constructed by a microwire (cylindrical working electrode) traversing a film of ionic liquid (1‐butyl‐1‐methylpyrrolidinium bis(trifluoromethylsulfonyl)imide) that is suspended within a wire loop (reference/counter electrode). An ionic liquid is chosen because the low vapor pressure preserves the film over weeks, vastly improving suspended film electroanalysis. The resultant high surface area allows the suspended ionic liquid cell to act as an aerosol net. Given the hydrophobic nature of the ionic liquid, aqueous aerosol particles do not coalesce into the film. When the liquid aerosols collide with the sufficiently biased microwire (creating a complex boundary: aerosol|wire|ionic liquid|air), the electrochemistry within a single liquid aerosol particle can be interrogated in real‐time. The ability to achieve liquid aerosol size distributions for aerosols over 1 µm in radius is demonstrated.more » « less
-
Abstract Flexible sensors with accurate detection of environmental stimuli (e.g., humidity and chemical substances) have drawn increasing research interests in biomedical engineering and environmental science. However, most work is focused on isotropic sensing of liquid occurrence due to the limitation of material development, sensor design, and fabrication capability. 3D printing is used to build multifunctional flexible liquid sensors with multimaterials enabling anisotropic detection of microliquid droplets, and described herein. Electrical conductive composite hydrogels capable of detecting chemical liquid are developed with poly (ethylene diacrylate) (PEGDA) and multiwalled carbon nanotube (MWCNT). Due to the absorption of the liquid droplet and related swelling behavior, the resistance of PEGDA/MWCNT composite hydrogel increases dramatically, while the resistance of pure PEGDA hydrogel decreases significantly. Based on the two composite hydrogels and the related 3D printing method, a mesh‐shaped liquid sensor that can effectively identify the position and volume of liquid leakage in a short time is developed. Furthermore, a three‐layered liquid sensor to enable bidirectional monitor and detection of the liquid leakage in two different sides is demonstrated. The 3D‐printed liquid sensor offers a distinctive perspective on the potential applications in various fields for detection of liquid leakage in accurate position and direction.more » « less
