Grading of bandgap by alloying CdTe with selenium to form a CdSe
Note: When clicking on a Digital Object Identifier (DOI) number, you will be taken to an external site maintained by the publisher.
Some full text articles may not yet be available without a charge during the embargo (administrative interval).
What is a DOI Number?
Some links on this page may take you to non-federal websites. Their policies may differ from this site.
-
more » « less
x Te1–x /CdTe‐graded bilayer device has led to a device efficiency over 19%. A CdSex Te1–x absorber would increase the short‐circuit current due to its lower bandgap but at the expense of open‐circuit voltage. It has been demonstrated that adding a CdTe layer at the back of such a CdSex Te1–x film reduces the voltage deficit caused by the lower bandgap of absorber from selenium alloying while maintaining the higher short‐circuit current. This leads to a photovoltaic device that draws advantage from both materials with an efficiency greater than either of them. Herein, a detailed account using device data, ultraviolet photoelectron spectroscopy, electron microscopy, and first‐principles density functional theory modeling is provided, which shows that CdTe acts as an electron reflector for CdSex Te1–x . -
This paper investigates the suitability of CdTe photovoltaic cells to be used as power sources for wireless sensors located in buildings. We fabricate and test a CdTe photovoltaic cell with a transparent conducting oxide front contact that provides for high photocurrents and low series resistance at low light intensities - and measure the photovoltaic response of this cell across five orders of magnitude of AM1.5G light intensity. Efficiencies of 10% and 17.1% are measured under ~1 W/m2 AM1.5G and LED irradiance respectively, the highest values for a CdTe device under ambient lighting measured to date. We use our results to assess the potential of CdTe for internet of things devices from an optoelectronic, as well as a techno-economic perspective, considering its established manufacturing know-how, potential for low-cost, proven long-term stability and issues around the use of cadmium.more » « less
-
A thin layer of Al 2 O 3 at the back of CdSe x T e1-x /CdTe devices is shown to passivate the back interface and drastically improve surface recombination lifetimes and photoluminescent response. Despite this, such devices do not show an improvement in open-circuit voltage (V OC. ) Adding a p + amorphous silicon layer behind the Al 2 O 3 bends the conduction band upward, reducing the barrier to hole extraction and improving collection. Further optimization of the Al 2 O 3 , amorphous silicon (a-Si), and indium-doped tin oxide (ITO) layers, as well as their interaction with the CdCl 2 passivation process, are necessary to translate these electro-optical improvements into gains in voltage.more » « less
-
CdTe thin-film photovoltaics have demonstrated some of the lowest costs of electricity generation owing to its low material cost and ease of manufacturing. However, the full potential of polycrystalline CdTe photovoltaics can only be realized if the open-circuit voltage can be increased beyond 1 V Open-circuit voltage ~850-900 mV has been consistently observed for state-of-the-art polycrystalline CdTe solar cells. Open-circuit voltage of over 1V has been demonstrated for single crystal CdTe devices by doping with Group V elements. Therefore, this study is aimed at understanding behavior of polycrystalline CdTe devices with arsenic doping, its activation and process and performance optimization in order to overcome current voltage limitations in CdTe solar cells.more » « less
-
CdTe photovoltaic devices with a ZnTe back contact have the potential to improve device performance and stability. After performing a sweep of ZnTe deposition and annealing temperatures, device performances were evaluated. Copper doping was performed after the ZnTe depositions by sublimating CuCl. Initial results indicate that ZnTe deposited and annealed for 20 minutes at 250°C improved device performance in terms of fill factor, J SC , and V OC as compared to other deposition temperatures. Copper doping also impacted device performance and a longer copper treatment on ZnTe led to a 17.6% device.more » « less
