Search for: All records

Aqueous zinc ion batteries (AZIBs) have considerable potential for energy storage owing to their cost-effectiveness, safety, and environmental sustainability. However, dendrite formation, hydrogen evolution reaction (HER), and corrosion of the bare zinc (B-Zn) anode tremendously impact the performance degradation and premature failure of AZIBs. This study introduces a glancing angle deposition (GLAD) approach during the sputtering process to fabricate tellurium nanostructured (TeNS) at the zinc (Zn) anode to avoid the aforementioned issues with the B-Zn anode. Three different deposition times (5, 10, and 30 min) were used to prepare TeNS at the Zn anode. The morphology, crystallinity, composition, and wettability of the TeNSs were analyzed. The TeNSs served as hydrophilic sites and a protective layer, facilitating uniform Zn nucleation and plating while inhibiting dendrite formation and side reactions. Consequently, the symmetric cell with TeNS deposited on the Zn anode for 10 min (Te@Zn_10 min) demonstrated an enhanced cycling stability of 350 h, the lowest nucleation overpotential of 10.65 mV at a current density of 1 mA/cm2, and an areal capacity of 0.5 mAh/cm2. The observed enhancement in the cycling stability and reduction in the nucleation overpotential can be attributed to the optimal open area fraction of the TeNSs on the Zn surface, which promotes uniform Zn deposition while effectively suppressing side reactions. 

Tellurium is a heavy chemical element exhibiting chirality, anisotropy, and strong spin-orbit coupling; conse quently, displaying a huge potential in quantum hardware technologies. In this article, tellurium quantum dots, with sizes around 19 ± 3 nm and energy bandgap around 2.4 eV, were successfully synthesized by pulsed laser ablation in liquids (PLAL). The synthesis was performed by using a nanosecond Nd:YAG laser emitting at 1064 nm and pulsing the laser beam at 1 kHz. Toluene (C6H5CH3) was used as a solvent to avoid oxidation of the dots. Non-polarized and polarized Raman spectroscopy as well as X-Ray diffraction were performed on the dots to study their quantum confinement and anisotropy. Finally, strongly confined tellurium quantum dots were obtained; and, their properties underline their potential as quantum light sources. 

Recently, various methods have been developed for synthesizing zinc oxide (ZnO) nanostructures, including physical and chemical vapor deposition, as well as wet chemistry. These common methods require either high temperature, high vacuum, or toxic chemicals. In this study, we report the growth of zinc oxide ZnO nanowires by a new hot water deposition (HWD) method on various types of substrates, including copper plates, foams, and meshes, as well as on indium tin oxide (ITO)-coated glasses (ITO/glass). HWD is derived from the hot water treatment (HWT) method, which involves immersing piece(s) of metal and substrate(s) in hot deionized water and does not require any additives or catalysts. Metal acts as the source of metal oxide molecules that migrate in water and deposit on the substrate surface to form metal oxide nanostructures (MONSTRs). The morphological and crystallographic analyses of the source-metals and substrates revealed the presence of uniformly crystalline ZnO nanorods after the HWD. In addition, the growth mechanism of ZnO nanowires using HWD is discussed. This process is simple, inexpensive, low temperature, scalable, and eco-friendly. Moreover, HWD can be used to deposit a large variety of MONSTRs on almost any type of substrate material or geometry. 

Encapsulating Cs4PbBr6 quantum dots in silicon nano-sheets not only stabilizes the halide perovskite, but also takes advantage of the nano-sheet for a compatible integration with the traditional silicon semiconductor. Here, we report the preparation of un-passivated Cs4PbBr6 ellipsoidal nanocrystals and pseudo-spherical quantum dots in silicon nano-sheets and their enhanced photoluminescence (PL). For a sample with low concentrations of quantum dots in silicon nano-sheets, the emission from Cs4PbBr6 pseudo-spherical quantum dots is quenched and is dominated with Pb2+ ion/silicene emission, which is very stable during the whole measurement period. For a high concentration of Cs4PbBr6 ellipsoidal nanocrystals in silicon nano-sheets, we have observed Förster resonance energy transfer with up to 87% efficiency through the oscillation of two PL peaks when UV excitation switches between on and off, using recorded video and PL lifetime measurements. In an area of a non-uniform sample containing both ellipsoidal nanocrystals and pseudo-spherical quantum dots, where Pb2+ ion/silicene emissions, broadband emissions from quantum dots, and bandgap edge emissions (515 nm) appear, the 515 nm peak intensity increases five times over 30 min of UV excitation, probably due to a photon recycling effect. This irradiated sample has been stable for one year of ambient storage. Cs4PbBr6 quantum dots encapsulated in silicon nano-sheets can lead to applications of halide perovskite light emitting diodes (PeLEDs) and integration with traditional semiconductor materials. 

Hot water treatment (HWT) is a versatile technique for synthesizing metal oxide nanostructures (MONSTRs) by immersing metal substrates in hot water, typically in glass beakers. The proximity of substrates to the heat source during HWT can influence the temperature of the substrate and subsequently impact MONSTR growth. In our study, zinc (Zn) substrates underwent HWT at the base of a glass beaker in contact with a hot plate and at four different vertical distances from the base. While the set temperature of deionized (DI) water was 75.0 °C, the substrate locations exhibited variations, notably with the base reaching 95.0 °C. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and Raman spectroscopy showed stoichiometric and crystalline zinc oxide (ZnO) nanorods. ZnO rods on the base, exposed to higher temperatures, displayed greater growth in length and diameter, and higher crystallinity. Nanorods with increasing vertical distances from the base exhibited a logarithmic decrease in length despite identical temperatures, whereas their diameters remained constant. We attribute these findings to crucial HWT growth mechanisms like surface diffusion and “plugging”, influenced by temperature and water flow within the beaker. Our results provide insights for optimizing synthesis parameters to effectively control MONSTR growth through HWT.