skip to main content


Title: ZIF-67-derived edge-oriented graphene clusters coupled with carbon nanotubes containing encapsulated Co nanoparticles for high-frequency electrochemical capacitors
There is a strong interest in increasing the frequency response of electrochemical capacitors (ECs) from typically less than 1 Hz to the hundreds or the kilo Hz range, so that such high-frequency ECs (HF-ECs) could replace conventional capacitors for AC line-frequency filtering and other capacitor applications. The development of such HF-ECs is hindered by their typically low capacitance density and operation voltage. Herein, by treating ZIF-67 particulate films in CH 4 /H 2 plasma, edge-oriented graphene (EOG) formed around the carbonized ZIF-67 particulate skeleton, and this EOG was coupled with carbon nanotubes (CNTs) that were grown with the aid of Co catalyst nanoparticles, which were generated by reducing the Co 2+ ions associated with ZIF in the plasma. Used as electrodes, these EOG/CNT/carbonized ZIF-67 composites exhibited a large electrode areal capacitance of 1.0 mF cm −2 and an excellent frequency response of −84° phase angle at 120 Hz in aqueous electrolyte cells, whereas values of 0.67 mF cm −2 and −78° for the electrode areal capacitance and the phase angle at 120 Hz, respectively, were obtained in organic electrolyte cells with the operation voltage of 2.5 V. Using three pairs of electrodes stacked together, a single integrated cell operating at 7.5 V and having a characteristic frequency of ∼3.8 kHz at −45° phase angle, was demonstrated. These results suggest the potential to use this EOG/CNT/carbonized ZIF-67 composite structure for developing HF-ECs.  more » « less
Award ID(s):
1611060 1820098
NSF-PAR ID:
10114168
Author(s) / Creator(s):
; ; ; ; ;
Date Published:
Journal Name:
Sustainable Energy & Fuels
ISSN:
2398-4902
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Abstract

    An ultra‐fast electrochemical capacitor (EC) designed for efficient ripple current smoothing was fabricated using vertically oriented MoS2(VOM) nanoflakes deposited on freestanding carbonized cellulose (CC) sheets as electrodes. The daily used cellulose tissue sheets were transformed into electrode scaffolds through a rapid pyrolysis process within a preheated furnace, on which VOM nanoflakes were formed in a conventional hydrothermal process. With these ~10 μm thick VOM‐CC electrodes, ultrafast ECs with tunable frequency response and specific capacitance density were fabricated. The ECs with a cell‐level areal capacitance density of 0.8 mF/cm2at 120 Hz were demonstrated for ripple current filtering from 60 Hz to 60 kHz. At a lower frequency response level, EC cell with a large capacitance density of 4.8 mF/cm2was also demonstrated. With the facile and easily scaled up process to producing the nanostructured electrode, the miniaturized VOM‐CC based ECs have the potential to substitute the bulky aluminum electrolytic capacitors for current smoothing and pulse power applications.

     
    more » « less
  2. ABSTRACT Compact-size kilohertz (kHz) AC-supercapacitors are being pursued for ripple current filtering and pulsed energy storage. However, their development is limited by a small areal capacitance density due to very thin electrode used for meeting frequency requirement. In our work, crosslinked carbon nanofiber aerogel (CCNFA) was investigated as freestanding electrode for kHz AC-supercapacitors with an areal capacitance density as large as 4.5 mF cm -2 at 120 Hz, 5-10 times larger than most reports. The CCNFA was obtained in a rapid plasma carbonization process of bacterial cellulose. The fabrication route adopted here is simple and straightforward, and the produced CCNFA electrode was found to be very suitable for high-frequency AC-supercapacitors. The operating voltage range of CCNFA based AC-supercapacitors can be expanded to 3 V by utilizing an organic electrolyte. In addition to AC-Supercapacitor performance, the morphology and material properties of bacterial cellulose aerogel and CCNFA were also reported. 
    more » « less
  3. Dutta, Achyut K. ; Balaya, Palani ; Xu, Sheng (Ed.)
    Monitoring human health in real-time using wearable and implantable electronics (WIE) has become one of the most promising and rapidly growing technologies in the healthcare industry. In general, these electronics are powered by batteries that require periodic replacement and maintenance over their lifetime. To prolong the operation of these electronics, they should have zero post-installation maintenance. On this front, various energy harvesting technologies to generate electrical energy from ambient energy sources have been researched. Many energy harvesters currently available are limited by their power output and energy densities. With the miniaturization of wearable and implantable electronics, the size of the harvesters must be miniaturized accordingly in order to increase the energy density of the harvesters. Additionally, many of the energy harvesters also suffer from limited operational parameters such as resonance frequency and variable input signals. In this work, low frequency motion energy harvesting based on reverse electrowetting-ondielectric (REWOD) is examined using perforated high surface area electrodes with 38 µm pore diameters. Total available surface area per planar area was 8.36 cm2 showing a significant surface area enhancement from planar to porous electrodes and proportional increase in AC voltage density from our previous work. In REWOD energy harvesting, high surface area electrodes significantly increase the capacitance and hence the power density. An AC peak-to-peak voltage generation from the electrode in the range from 1.57-3.32 V for the given frequency range of 1-5 Hz with 0.5 Hz step is demonstrated. In addition, the unconditioned power generated from the harvester is converted to a DC power using a commercial off-theshelf Schottky diode-based voltage multiplier and low dropout regulator (LDO) such that the sensors that use this technology could be fully self-powered. The produced charge is then converted to a proportional voltage by using a commercial charge amplifier to record the features of the motion activities. A transceiver radio is also used to transmit the digitized data from the amplifier and the built-in analog-to-digital converter (ADC) in the micro-controller. This paper proposes the energy harvester acting as a self-powered motion sensor for different physical activities for wearable and wireless healthcare devices. 
    more » « less
  4. Abstract

    Electrochemical capacitors (ECs) that store charge based on the pseudocapacitive mechanism combine high energy densities with high power densities and rate capabilities. 2D transition metal carbides (MXenes) have been recently introduced as high‐rate pseudocapacitive materials with ultrahigh areal and volumetric capacitances. So far, 20 different MXene compositions have been synthesized and many more are theoretically predicted. However, since most MXenes are chemically unstable in their 2D forms, to date only one MXene composition, Ti3C2Tx, has shown stable pseudocapacitive charge storage. Here, a cation‐driven assembly process is demonstrated to fabricate highly stable and flexible multilayered films of V2CTxand Ti2CTxMXenes from their chemically unstable delaminated single‐layer flakes. The electrochemical performance of electrodes fabricated using assembled V2CTxflakes surpasses Ti3C2Txin various aqueous electrolytes. These electrodes show specific capacitances as high as 1315 F cm−3and retain ≈77% of their initial capacitance after one million charge/discharge cycles, an unprecedented performance for pseudocapacitive materials. This work opens a new venue for future development of high‐performance supercapacitor electrodes using a variety of 2D materials as building blocks.

     
    more » « less
  5. Abstract

    Formation of thick, high energy density, flexible solid supercapacitors is challenging because of difficulties infilling gel electrolytes into porous electrodes. Incomplete infilling results in a low capacitance and poor mechanical properties. Here we report a bottom-up infilling method to overcome these challenges. Electrodes up to 500 μm thick, formed from multi-walled carbon nanotubes and a composite of poly(3,4-ethylenedioxythiophene), polystyrene sulfonate and multi-walled carbon nanotubes are successfully infilled with a polyvinyl alcohol/phosphoric acid gel electrolyte. The exceptional mechanical properties of the multi-walled carbon nanotube-based electrode enable it to be rolled into a radius of curvature as small as 0.5 mm without cracking and retain 95% of its initial capacitance after 5000 bending cycles. The areal capacitance of our 500 μm thick poly(3,4-ethylenedioxythiophene), polystyrene sulfonate, multi-walled carbon nanotube-based flexible solid supercapacitor is 2662 mF cm–2at 2 mV s–1, at least five times greater than current flexible supercapacitors.

     
    more » « less