skip to main content


Title: Hierarchical chemomechanical encoding of multi-responsive hydrogel actuators via 3D printing
Inspired by nature, we herein demonstrate a family of multi-responsive hydrogel-based actuators that are encoded with anisotropic swelling behavior to provide rapid and controllable motion. Fabrication of the proposed anisotropy-encoded hydrogel actuators relies on the high resolution stereolithography 3D printing of functionally graded structures made of discrete layers having different volume expansion properties. Three separate synthetic strategies based on (i) asymmetrical distribution of a layer's surface area to volume ratio via mechanical design, (ii) crosslinking density via UV photo-exposure, or (iii) chemical composition via resin vat exchange have been accordingly demonstrated for developing very smooth gradients within the printed hydrogel-based actuator. Our chemomechanical programming enables fast, reversible, repeatable and multimodal bending actuation in response to any immediate environmental change ( i.e. based on osmotic pressure, temperature and pH) from a single printed structure.  more » « less
Award ID(s):
1719875
NSF-PAR ID:
10148500
Author(s) / Creator(s):
; ; ; ; ; ; ; ;
Date Published:
Journal Name:
Journal of Materials Chemistry A
Volume:
7
Issue:
25
ISSN:
2050-7488
Page Range / eLocation ID:
15395 to 15403
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Abstract

    A comprehensive material system is introduced for the additive manufacturing of electrohydraulic (HASEL) tentacle actuators. This material system consists of a photo‐curable, elastomeric silicone‐urethane with relatively strong dielectric properties (εr ≈ 8.8 at 1 kHz) in combination with ionically‐conductive hydrogel and silver paint electrodes that displace a vegetable‐based liquid dielectric under the application of an electric field. The electronic properties of the silicone material as well as the mechanical properties of the constitutive silicone and hydrogel materials are investigated. The hydraulic pressure exerted on the dielectric working fluid in these capacitive actuators is measured in order to characterize their quasi‐static behavior. Various design features enabled by 3D printing influence this behavior—decreasing the voltage at which actuation begins or increasing the force density in the system. Using a capacitance change of >35% across the actuators while powered, a demonstration of self‐sensing inherent to HASELs is shown. Antagonistic pairs of the 3D printed actuators are shown to exert a blocked force of over 400 mN. An electrohydraulic tentacle actuator is then fabricated to demonstrate the use of this material and actuation system in a synthetic hydrostat. This tentacle actuator is shown to achieve motion in a multi‐dimensional space.

     
    more » « less
  2. Jabbari, Esmaiel (Ed.)
    This study presents novel biocompatible Polydimethylsiloxane (PDMS)-based micromechanical tweezers (μTweezers) capable of the stiffness characterization and manipulation of hydrogel-based organoids. The system showed great potential for complementing established mechanical characterization methods such as Atomic Force Microscopy (AFM), parallel plate compression (PPC), and nanoindentation, while significantly reducing the volume of valuable hydrogels used for testing. We achieved a volume reduction of ~0.22 μl/sample using the μTweezers vs. ~157 μl/sample using the PPC, while targeting high-throughput measurement of widely adopted micro-mesoscale (a few hundred μm-1500 μm) 3D cell cultures. The μTweezers applied and measured nano-millinewton forces through cantilever’ deflection with high linearity and tunability for different applications; the assembly is compatible with typical inverted optical microscopes and fit on standard tissue culture Petri dishes, allowing mechanical compression characterization of arrayed 3D hydrogel-based organoids in a high throughput manner. The average achievable output per group was 40 tests per hour, where 20 organoids and 20 reference images in one 35 mm petri dish were tested, illustrating efficient productivity to match the increasing demand on 3D organoids’ applications. The changes in stiffness of collagen I hydrogel organoids in four conditions were measured, with ovarian cancer cells (SKOV3) or without (control). The Young’s modulus of the control group (Control—day 0, E = 407± 146, n = 4) measured by PPC was used as a reference modulus, where the relative elastic compressive modulus of the other groups based on the stiffness measurements was also calculated (control-day 0, E = 407 Pa), (SKOV3-day 0, E = 318 Pa), (control-day 5, E = 528 Pa), and (SKOV3-day 5, E = 376 Pa). The SKOV3-embedded hydrogel-based organoids had more shrinkage and lowered moduli on day 0 and day 5 than controls, consistently, while SKOV3 embedded organoids increased in stiffness in a similar trend to the collagen I control from day 0 to day 5. The proposed method can contribute to the biomedical, biochemical, and regenerative engineering fields, where bulk mechanical characterization is of interest. The μTweezers will also provide attractive design and application concepts to soft membrane-micro 3D robotics, sensors, and actuators. 
    more » « less
  3. In the last decade, 3D printing has attracted significant attention and has resulted in benefits to many research areas. Advances in 3D printing with smart materials at the microscale, such as hydrogels and liquid crystalline polymers, have enabled 4D printing and various applications in microrobots, micro-actuators, and tissue engineering. However, the material absorption of the laser power and the aberrations of the laser light spot will introduce a decay in the polymerization degree along the height direction, and the solution to this problem has not been reported yet. In this paper, a compensation strategy for the laser power is proposed to achieve homogeneous and high aspect ratio hydrogel structures at the microscale along the out-of-plane direction. Linear approximations for the power decay curve are adopted for height steps, discretizing the final high aspect ratio structures. The strategy is achieved experimentally with hydrogel structures fabricated by two-photon polymerization. Moreover, characterizations have been conducted to verify the homogeneity of the printed microstructures. Finally, the saturation of material property is investigated by an indirect 3D deformation method. The proposed strategy is proved to be effective and can be explored for other hydrogel materials showing significant deformation. Furthermore, the strategy for out-of-plane variations provides a critical technique to achieve 4D-printed homogeneous shape-adaptive hydrogels for further applications. 
    more » « less
  4. In both biological and engineered systems, functioning at peak power output for prolonged periods of time requires thermoregulation. Here, we report a soft hydrogel-based actuator that can maintain stable body temperatures via autonomic perspiration. Using multimaterial stereolithography, we three-dimensionally print finger-like fluidic elastomer actuators having a poly- N -isopropylacrylamide (PNIPAm) body capped with a microporous (~200 micrometers) polyacrylamide (PAAm) dorsal layer. The chemomechanical response of these hydrogel materials is such that, at low temperatures (<30°C), the pores are sufficiently closed to allow for pressurization and actuation, whereas at elevated temperatures (>30°C), the pores dilate to enable localized perspiration in the hydraulic actuator. Such sweating actuators exhibit a 600% enhancement in cooling rate (i.e., 39.1°C minute −1 ) over similar non-sweating devices. Combining multiple finger actuators into a single device yields soft robotic grippers capable of both mechanically and thermally manipulating various heated objects. The measured thermoregulatory performance of these sweating actuators (~107 watts kilogram −1 ) greatly exceeds the evaporative cooling capacity found in the best animal systems (~35 watts kilogram −1 ) at the cost of a temporary decrease in actuation efficiency. 
    more » « less
  5. Abstract

    Untethered stimuli‐responsive soft materials with programmed sequential self‐folding are of great interest due to their ability to achieve task‐specific shape transformation with complex final configuration. Here, reversible and sequential self‐folding soft actuators are demonstrated by utilizing a temperature‐responsive nanocomposite hydrogel with different folding speeds but the same chemical composition. By varying the UV light intensity during the photo‐crosslinking of the nanocomposite hydrogel, different types of microstructures can be realized via phase separation mechanisms, which allow to control the folding speeds. The self‐folding structures are fabricated by integrating two dissimilar materials (i.e., a nanocomposite hydrogel and an elastomer) into hinge‐based bilayer structures via extrusion‐based 3D printing. It has been demonstrated that the folding kinetics can be accelerated by more than one order of magnitude due to the phase‐separated microstructure formed by the relatively weaker UV intensity (≈10 mW cm‐2) compared to the one formed by stronger UV intensity (≈100 mW cm‐2). 3D structures with sequential self‐folding capabilities are realized by prescribing actuation speeds and folding angles to specific hinges of the nanocomposite hydrogel. Sequential folding box and self‐locking latch structures are fabricated to demonstrate the ability to capture and hold objects underwater.

     
    more » « less