An official website of the United States government
Wavelength tracking is a commonly used method for demodulating fiber-optic Fabry–Perot interferometric sensors due to its high resolution and straightforward implementation. We report the observation of random spurious jumps in a commonly used wavelength-tracking method based on curve fitting. These jumps were unrelated to the phase ambiguity of the spectral fringes and led to measurement errors. We analyzed the origin of the spurious jumps through Monte Carlo simulations where the fringe valley positions were obtained using polynomial curve fittings. The simulation results show that the spurious jumps arose mainly from the systematic errors of the curve-fitting function for modeling the sensor spectrum and manifested themselves by the changes in the pixel set for curve fitting. The centroid method also suffered from the spurious jumps. We proposed a modified correlation demodulation method free of the spurious jumps. In this method, the information of the measurand was obtained through the correlation between the measured sensor spectral frames and a sufficiently large number of calibrated frames of the sensor over the measurement range. The simulation and experimental results show that the modified correlation method was free of the spurious jumps encountered in the regular wavelength tracking. The resolution of the method was also studied and compared with the curve-fitting method.
more »
« less
Analysis of single-mode fiber-optic extrinsic Fabry–Perot interferometric sensors with planar metal mirrors
We theoretically study the spectral characteristics and noise performance of wavelength-interrogated fiber-optic sensors based on an extrinsic Fabry–Perot (FP) interferometer (EFPI) formed by thin metal mirrors. We develop a model and use it to analyze the effect of key sensor parameters on the visibility and spectral width of the sensors, including the beam width of the incident light, metal coating film thickness, FP cavity length, and wedge angle of the two mirrors. Through Monte Carlo simulations, we obtain an empirical equation that can be used to estimate the wavelength resolution from the visibility and spectral width, which can be used as a figure-of-merit that is inherent to the sensor and independent on the system noises. The work provides a useful tool for designing, constructing, and interrogating high-resolution fiber-optic EFPI sensors.
more »
« less
- Award ID(s):
- 1918074
- PAR ID:
- 10292243
- Publisher / Repository:
- Optical Society of America
- Date Published:
- Journal Name:
- Applied Optics
- Volume:
- 60
- Issue:
- 26
- ISSN:
- 1559-128X; APOPAI
- Format(s):
- Medium: X Size: Article No. 7894
- Size(s):
- Article No. 7894
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Additive manufacturing (AM) enables the spatially configurable 3D integration of sensors in metal components to realize smart materials and structures. Outstanding sensing capabilities and size compatibility have made fiber optic sensors excellent candidates for integration in AM components. In this study, fiber Bragg grating (FBG) sensors were embedded in Inconel 718 tensile coupons printed using laser powder bed fusion AM. On-axis (fiber runs through the coupon’s center of axis) and off-axis (fiber is at 5° and 10° to the coupon’s center of axis) sensors were buried in epoxy resin inside narrow channels that run through the coupons. FBGs’ spectral evolutions during embedment in the coupons were examined and cyclic loading experiments were conducted to analyze and evaluate the sensor integration process, complex strain loading, process flaws, and sensing performance. This study also demonstrates that the AM process-born deficiencies such as poor surface finish and staircase effects can be detrimental to the embedded sensors and their sensing performance.more » « less
-
We demonstrate the fabrication of fiber-optic Fabry–Perot interferometer (FPI) temperature sensors by bonding a small silicon diaphragm to the tip of an optical fiber using low melting point glass powders heated by a 980 nm laser on an aerogel substrate. The heating laser is delivered to the silicon FPI using an optical fiber, while the silicon temperature is being monitored using a 1550 nm white-light system, providing localized heating with precise temperature control. The use of an aerogel substrate greatly improves the heating efficiency by reducing the thermal loss of the bonding parts to the ambient environment. A desirable temperature for bonding can be achieved with relatively small heating laser power. The bonding process is carried out in an open space at room temperature for convenient optical alignment. The precise temperature control ensures minimum perturbation to the optical alignment and no induced thermal damage to the optical parts during the bonding process. For demonstration, we fabricated a low-finesse and high-finesse silicon FPI sensor and characterized their measurement resolution and temperature capability. The results show that the fabrication method has a good potential for high-precision fabrication of fiber-optic sensors.more » « less
-
Abstract. A novel fiber-optic distributed temperature sensing instrument, the Fiber-optic Laser Operated Atmospheric Temperature Sensor (FLOATS), was developed for continuous in situ profiling of the atmosphere up to 2 km below constant-altitude scientific balloons. The temperature-sensingsystem uses a suspended fiber-optic cable and temperature-dependent scattering of pulsed laser light in the Raman regime to retrieve continuous3 m vertical-resolution profiles at a minimum sampling period of 20 s.FLOATS was designed for operation aboard drifting super-pressure balloons inthe tropical tropopause layer at altitudes around 18 km as part of theStratéole 2 campaign. A short test flight of the system was conductedfrom Laramie, Wyoming, in January 2021 to check the optical, electrical, andmechanical systems at altitude and to validate a four-reference temperaturecalibration procedure with a fiber-optic deployment length of 1170 m. During the 4 h flight aboard a vented balloon, FLOATS retrieved temperatureprofiles during ascent and while at a float altitude of about 19 km. TheFLOATS retrievals provided differences of less than 1.0 ∘Ccompared to a commercial radiosonde aboard the flight payload during ascent.At float altitude, a comparison of optical length and GPS position at thebottom of the fiber-optic revealed little to no curvature in the fiber-opticcable, suggesting that the position of any distributed temperaturemeasurement can be effectively modeled. Comparisons of the distributed temperature retrievals to the reference temperature sensors show strongagreement with root-mean-square-error values less than 0.4 ∘C. Theinstrument also demonstrated good agreement with nearby meteorologicalobservations and COSMIC-2 satellite profiles. Observations of temperatureand wind perturbations compared to the nearby radiosounding profiles provide evidence of inertial gravity wave activity during the test flight. Spectral analysis of the observed temperature perturbations shows that FLOATS is an effective and pioneering tool for the investigation of small-scale gravity waves in the upper troposphere and lower stratosphere.more » « less
-
A spatial heterodyne Raman spectrometer (SHRS), constructed using a modular optical cage and lens tube system, is described for use with a commercial silica and a custom single-crystal (SC) sapphire fiber Raman probe. The utility of these fiber-coupled SHRS chemical sensors is demonstrated using 532 nm laser excitation for acquiring Raman measurements of solid (sulfur) and liquid (cyclohexane) Raman standards as well as real-world, plastic-bonded explosives (PBX) comprising 1,3,5- triamino- 2,4,6- trinitrobenzene (TATB) and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) energetic materials. The SHRS is a fixed grating-based dispersive interferometer equipped with an array detector. Each Raman spectrum was extracted from its corresponding fringe image (i.e., interferogram) using a Fourier transform method. Raman measurements were acquired with the SHRS Littrow wavelength set at the laser excitation wavelength over a spectral range of ∼1750 cm−1with a spectral resolution of ∼8 cm−1for sapphire and ∼10 cm−1for silica fiber probes. The large aperture of the SHRS allows much larger fiber diameters to be used without degrading spectral resolution as demonstrated with the larger sapphire collection fiber diameter (330 μm) compared to the silica fiber (100 μm). Unlike the dual silica fiber Raman probe, the dual sapphire fiber Raman probe did not include filtering at the fiber probe tip nearest the sample. Even so, SC sapphire fiber probe measurements produced less background than silica fibers allowing Raman measurements as close as ∼85 cm−1to the excitation laser. Despite the short lengths of sapphire fiber used to construct the sapphire probe, well-defined, sharp sapphire Raman bands at 420, 580, and 750 cm−1were observed in the SHRS spectra of cyclohexane and the highly fluorescent HMX-based PBX. SHRS measurements of the latter produced low background interference in the extracted Raman spectrum because the broad band fluorescence (i.e., a direct current, or DC, component) does not contribute to the interferogram intensity (i.e., the alternating current, or AC, component). SHRS spectral resolution, throughput, and signal-to-noise ratio are also discussed along with the merits of using sapphire Raman bands as internal performance references and as internal wavelength calibration standards in Raman measurements.more » « less
