skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Crystallographic texture dependent bulk anisotropic elastic response of additively manufactured Ti6Al4V
Abstract Rapid thermokinetics associated with laser-based additive manufacturing produces strong bulk crystallographic texture in the printed component. The present study identifies such a bulk texture effect on elastic anisotropy in laser powder bed fused Ti6Al4V by employing an effective bulk modulus elastography technique coupled with ultrasound shear wave velocity measurement at a frequency of 20 MHz inside the material. The combined technique identified significant attenuation of shear velocity from 3322 ± 20.12 to 3240 ± 21.01 m/s at 45 $$^\circ$$ ∘ and 90 $$^\circ$$ ∘ orientations of shear wave plane with respect to the build plane of printed block of Ti6Al4V. Correspondingly, the reduction in shear modulus from 48.46 ± 0.82 to 46.40 ± 0.88 GPa was obtained at these orientations. Such attenuation is rationalized based on the orientations of $$\alpha ^\prime$$ α ′ crystallographic variants within prior columnar $$\beta$$ β grains in additively manufactured Ti6Al4V.  more » « less
Award ID(s):
1741677
PAR ID:
10300025
Author(s) / Creator(s):
; ; ; ; ; ; ; ; ; ;
Date Published:
Journal Name:
Scientific Reports
Volume:
11
Issue:
1
ISSN:
2045-2322
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; (, American Mineralogist)
    null (Ed.)
    Abstract We investigated the structure, equation of state, thermodynamics, and elastic properties of tremolite amphibole [Ca2Mg5Si8O22(OH)2] up to 10 GPa and 2000 K, using first principles simulations based on density functional perturbation theory. We found that at 300 K, the pressure-volume results can be adequately described by a third-order Birch-Murnaghan equation of state with bulk moduli K0 of 78.5 and 66.3 GPa based on local density approximation (LDA) and generalized gradient approximation (GGA), respectively. We also derived its coefficients of the elastic tensor based on LDA and GGA and found that the LDA result is in good agreement with the experimental results. At 300 K, the shear modulus G0 is 58.0 GPa based on LDA. The pressure derivative of the bulk modulus K′ is 5.9, while that of the shear modulus G′ is 1.3. The second Grüneisen parameter, or δT = [–1/(αKT)](∂KT/∂T)P, is 3.3 based on LDA. We found that at ambient conditions, tremolite is elastically anisotropic with the compressional wave velocity anisotropy AVP being 34.6% and the shear wave velocity anisotropy AVS being 27.5%. At higher pressure corresponding to the thermodynamic stability of tremolite, i.e., ~3 GPa, the AVP reduces to 29.5%, whereas AVS increases to 30.8%. To evaluate whether the presence of hydrous phases such as amphibole and phlogopite could account for the observed shear wave velocity (VS) anomaly at the mid-lithospheric discontinuity (MLD), we used the thermoelasticities of tremolite (as a proxy for other amphiboles), phlogopite, and major mantle minerals to construct synthetic velocity profiles. We noted that at depths corresponding to the mid-lithosphere, the presence of 25 vol% amphibole and 1 vol% phlogopite could account for a VS reduction of 2.3%. Thus based on our thermoelasticity results on tremolite amphibole, it seems that mantle metasomatism could partly explain the MLD. 
    more » « less
  2. ; ; ; ; ; ; ; (, Polymers)
    null (Ed.)
    In this study, a novel ultrasonic non-destructive and non-invasive elastography method was introduced and demonstrated to evaluate the mechanical properties of fused deposition modeling 3D printed objects using two-dimensional dynamical elasticity mapping. Based on the recently investigated dynamic bulk modulus and effective density imaging technique, an angle-dependent dynamic shear modulus measurement was performed to extract the dynamic Young’s modulus distribution of the FDM structures. The elastographic image analysis demonstrated the presence of anisotropic dynamic shear modulus and dynamic Young’s modulus existing in the fused deposition modeling 3D printed objects. The non-destructive method also differentiated samples with high contrast property zones from that of low contrast property regions. The angle-dependent elasticity contrast behavior from the ultrasonic method was compared with conventional and static tensile tests characterization. A good correlation between the nondestructive technique and the tensile test measurements was observed. 
    more » « less
  3. ; ; (, Geophysical Journal International)
    SUMMARY A robust, in situ estimate of shear-wave velocity VS and the small-strain damping ratio DS (or equivalently, the quality factor QS) is crucial for the design of buildings and geotechnical systems subjected to vibrations or earthquake ground shaking. A promising technique for simultaneously obtaining both VS and DS relies on the Multichannel Analysis of Surface Waves (MASW) method. MASW can be used to extract the Rayleigh wave phase velocity and phase attenuation data from active-source seismic traces recorded along linear arrays. Then, these data can be inverted to obtain VS and DS profiles. This paper introduces two novel methodologies for extracting the phase velocity and attenuation data. These new approaches are based on an extension of the beamforming technique which can be combined with a modal filter to isolate different Rayleigh propagation modes. Thus, the techniques return reliable phase velocity and attenuation estimates even in the presence of a multimode wavefield, which is typical of complex stratigraphic conditions. The reliability and effectiveness of the proposed approaches are assessed on a suite of synthetic wavefields and on experimental data collected at the Garner Valley Downhole Array and Mirandola sites. The results reveal that, under proper modelling of wavefield conditions, accurate estimates of Rayleigh wave phase velocity and attenuation can be extracted from active-source MASW wavefields over a broad frequency range. Eventually, the estimation of soil mechanical parameters also requires a robust inversion procedure to map the experimental Rayleigh wave parameters into soil models describing VS and DS with depth. The simultaneous inversion of phase velocity and attenuation data is discussed in detail in the companion paper. 
    more » « less
  4. ; ; ; ; (, Soils and Rocks)
    The in-situ small-strain shear modulus of soil and rock materials is a parameter of paramount importance in geotechnical modeling. It can be derived from non-invasive geophysical surveys, which provide the possibility of testing the subsurface in its natural and undisturbed condition by inferring the velocity of propagation of shear waves. In addition, for soil dynamics and earthquake engineering applications, the small-strain damping ratio plays a relevant role, yet its estimation is still challenging, lacking consolidated approaches for its in-situ evaluation. Recent advancements in instrumentation, such as distributed acoustic sensing (DAS), combined with advanced analysis methodologies for the interpretation of seismic wave propagation (e.g., machine learning and full waveform inversion), open new frontiers in site characterization. This paper presents and compares some advanced applications of measuring 1D and 2D variations in shear wave velocity and attenuation in-situ with reference to a specific case history. 
    more » « less
  5. ; ; (, International Journal of Applied Ceramic Technology)
    Abstract In order to investigate the in‐space in situ resource utilization, directed energy deposition (DED)‐based additive manufacturing (AM) has been utilized to process Martian regolith—Ti6Al4V (Ti64) composites. Here we investigated the processability of depositing 5, 10, and 100 wt% of Martian regolith premixed with Ti6Al4V using laser‐based DED, analyzing the printed structure via X‐ray diffraction, Vicker's microhardness, scanning electron microscopic imaging, and wear characteristics utilizing an abrasive water jet cutter to simulate abrasive environments on the Martian surface. The results indicate that the surface roughness and hardness of the composites increase with respect to the Martian regolith’ weight percentage due to in situ ceramic reinforcement. For instance, i5‐wt% addition of Martian regolith increased the Vicker's microhardness from 366 ± 6 HV0.2for as‐printed Ti64 to 730 ± 27 HV0.2while maintaining similar abrasive wear performance as Ti6Al4V. The results point toward laser‐based AM for fabricating Ti64—Martian regolith composites with comparable properties. The study also reveals promising results in limiting the mass burden for future space missions, resulting in cheaper and easier launches. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email