skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Electrochemical Polishing of Extruded and Laser Powder-Bed-Fused Inconel 718
ABSTRACTElectro-chemical polishing (ECP) was utilized to produce sub-micron surface finish on Inconel 718 parts manufactured by Laser Powder-Bed-Fusion (L-PBF) and extrusion methods. The L-PBF parts had very rough surfaces due to semi-welded powder particles, surface defects, and difference layer steps that were generally not found on surfaces of extruded and machined components. This study compared the results of electro-polishing of these differently manufactured parts under the same conditions. Titanium electrode was used with an acid-based electrolyte to polish both the specimens at different combinations of pulsed current density, duty cycle, and polishing time. Digital 3D optical profiler was used to assess the surface finish, while optical and scanning electron microscopy was utilized to observe the microstructure of polished specimens. At optimal condition, the ECP successfully reduced the surface of L-PBF part from 17 µm to 0.25 µm; further polishing did not improve the surface finish due to different removal rates of micro-leveled pores, cracks, nonconductive phases, and carbide particles in 3D-printed Inconel 718. The microstructure of extruded materials was uniform and free of processing defects, therefore can be polished consistently to 0.20 µm. Over-polishing of extruded material could improve its surface finish, but not for the L-PBF material due to defects and the surrounding micro-strain.  more » « less
Award ID(s):
1711917
PAR ID:
10323991
Author(s) / Creator(s):
; ; ;
Date Published:
Journal Name:
International Journal of Engineering Materials and Manufacture
Volume:
6
Issue:
4
ISSN:
0128-1852
Page Range / eLocation ID:
284 to 298
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; ; (, ASNT 27th Research Symposium Proceedings)
    The ability of Additive Manufacturing (AM) processes to ensure delivery of high quality metal-based components is somewhat limited by insufficient inspection capabilities. The inspection of AM parts presents particular challenges due to the design flexibility that the fabrication method affords. The nondestructive evaluation (NDE) methods employed need to be selected based on the material properties, type of possible defects, and geometry of the parts. Electromagnetic method, in particular Eddy Current (EC), is proposed for the inspections. This evaluation of EC inspection considers surface and near-surface defects in a stainless steel (SS) 17 4 PH additively manufactured sample and a SS 17 4 PH annealed plates manufactured traditionally (reference sample). The surfaces of the samples were polished using 1 micron polishing Alumina grit to achieve a mirror like surface finish. 1.02 mm (0.04”), 0.508 mm (0.02”) and 0.203 mm (0.008”) deep Electronic Discharge Machining (EDM) notches were created on the polished surface of the samples. Lift off and defect responses for both additive and reference samples were obtained using a VMEC-1 commercial instrument and a 500 kHz absolute probe. The inspection results as well as conductivity assessments for the AM sample in terms of the impedance plane signature were compared to response of similar features in the reference sample. Direct measurement of electromagnetic properties of the AM samples is required for precise inspection of the parts. Results show that quantitative comparison of the AM and traditional materials help for the development of EC technology for inspection of additively manufactured metal parts. 
    more » « less
  2. ; (, Proceedings of the ASME 2020 15th International Manufacturing Science and Engineering Conference MSEC2020)
    Abstract The present work utilizes Orientation Imaging Microscopy and Finite Element Modelling to analyse microstructure evolution in grains near defects during plane strain indentation of direct metal laser sintered Inconel 718. Defects are inevitably produced during printing of metals and they degrade the mechanical behaviour of parent components. Understanding microstructure evolution of grains present near defects can help create better predictive models of mechanical behaviour of components resulting from additive manufacturing. In this work, an ex-situ study of microstructure evolution during plane strain indentation of DMLS Inconel 718 specimens is performed. Regions that lie near volumetric porosity defects were studied. Grain Orientation Spread was utilized as a metric to quantify intra-granular deformation. It was seen that microstructure evolution of grains near defects is enhanced due to strain concentrations whereby they exhibit larger orientation spread after plastic deformation. Finite Element Analysis was used to simulate the plane strain indentation test on the specimen in which, porosity defects and roughness textures similar to those seen in the as-received specimen were programmed using the python scripting interface of Abaqus. Results from finite element analysis were compared with insights from microstructure analysis to describe evolution of microstructure during deformation near defects. 
    more » « less
  3. ; ; (, 28th International Solid Freeform Fabrication Symposium - An Additive Manufacturing Conference)
    The effects of build orientation on the fatigue behavior of additively-manufactured Ti-6Al- 4V using a Laser-Based Power Bed Fusion (L-PBF) process is investigated. Ti-6Al-4V rods were manufactured in vertical, horizontal, and 45º angle orientations. The specimens were then machined and polished along the gage section in order to reduce the effects of surface roughness on fatigue behavior. Fully-reversed strain-controlled uniaxial fatigue tests were performed at various strain amplitudes with frequencies adjusted to maintain an average constant strain rate throughout testing. Results indicate slight variation in fatigue behavior of specimens fabricated in the different orientations investigated. Fractography was conducted using scanning electron microscopy after mechanical testing in order to investigate the crack initiation sites and determine the defect responsible for the failure. The experimental program utilized and results obtained will be presented and discussed. 
    more » « less
  4. ; ; (, Materials Letters)
    Powder contamination during laser powder bed fusion is a critical concern for the quality assurance of parts. Herein, we studied the effect of Inconel 718 contamination on the properties of printed Ti6Al4V, two commonly printed alloys. Contaminated parts exhibited visual and microstructural defects, and a mere 0.5wt% IN718 contamination resulted in a 43% reduction in plastic strain without noticing surface-level cracking. Further contamination of 2.5 wt% IN718 promotes surface cracking that renders the material unable to deform plastically, highlighting the importance of proper powder handling and the detrimental effects that even small amounts of contaminants can have on AM-produced components. 
    more » « less
  5. ; (, Rapid Prototyping Journal)
    PurposeThe ability to use laser powder bed fusion (LPBF) to print parts with tailored surface topography could reduce the need for costly post-processing. However, characterizing the as-built surface topography as a function of process parameters is crucial to establishing linkages between process parameters and surface topography and is currently not well understood. The purpose of this study is to measure the effect of different LPBF process parameters on the as-built surface topography of Inconel 718 parts. Design/methodology/approachInconel 718 truncheon specimens with different process parameters, including single- and double contour laser pass, laser power, laser scan speed, build orientation and characterize their as-built surface topography using deterministic and areal surface topography parameters are printed. The effect of both individual process parameters, as well as their interactions, on the as-built surface topography are evaluated and linked to the underlying physics, informed by surface topography data. FindingsDeterministic surface topography parameters are more suitable than areal surface topography parameters to characterize the distinct features of the as-built surfaces that result from LPBF. The as-built surface topography is strongly dependent on the built orientation and is dominated by the staircase effect for shallow orientations and partially fused metal powder particles for steep orientations. Laser power and laser scan speed have a combined effect on the as-built surface topography, even when maintaining constant laser energy density. Originality/valueThis work addresses two knowledge gaps. (i) It introduces deterministic instead of areal surface topography parameters to unambiguously characterize the as-built LPBF surfaces. (ii) It provides a methodical study of the as-built surface topography as a function of individual LPBF process parameters and their interaction effects. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email