skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Rapid Adsorption of Cationic Methylene Blue Dye onto Volcanic Ash‑metakaolin Based Geopolymers
In this study, four geopolymer sorbents GP0, GP10, GP30 and GP50 were synthesized using volcanic ash (VA) and metakaolin (MK) blends as precursors with 0, 10, 30 and 50% MK content by mass, respectively. The materials were characterized by X-ray fuorescence (XRF), X-ray difraction (XRD), Raman spectroscopy, and Brunauer–Emmett–Teller (BET) surface area analyses, revealing successful geopolymerization of the precursors and increasing surface area with increasing MK content. The sorption performance of the VA, MK and VA-MK geopolymers was then evaluated for the removal of cationic methylene blue (MB) dye from aqueous media. Sorption capacity was independent of composition, providing fexibility in sorbent synthesis. Sorption rate, on the other hand, was 3–8 times greater for the VA-MK geopolymers than the precursor materials. The equilibrium adsorption data were suitably explained by the Freundlich model, denoting multilayer adsorption onto a heterogeneous adsorption surface with higher Freundlich afnity constant (KF) for geopolymers than VA. The adsorption kinetics obeyed the pseudo-second-order (PSO) kinetic law with an average of 98% removal efciency in 30 min. MB uptake was pH-dependent and driven by electrostatic chemisorption interactions. These results motivate further studies on the use of locally sourced geopolymers for water purifcation applications.  more » « less
Award ID(s):
2032590
PAR ID:
10342225
Author(s) / Creator(s):
; ; ; ;
Date Published:
Journal Name:
Silicon
ISSN:
1876-9918
Page Range / eLocation ID:
1-11
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; ; (, Coatings)
    This study reports on the highly simple fabrication of green carbon black (GCB) generated from scrap tires with acetic acid to improve the adsorption efficiency for water purification, which is thoroughly compared with conventional carbon black (CB) obtained from petrochemicals. Unlike traditional modification processes with strong acids or bases, the introduction of a relatively mild acid readily allowed for the effective modification of GCB to increase the uptake capability of metal ions and toxic organic dyes to serve as effective adsorbents. The morphological features and thermal decomposition patterns were examined by electron microscopy and thermogravimetric analysis (TGA). The surface functional groups were characterized by Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). The structural information (ratio of D-defects/G band-graphitic domains) obtained by Raman spectroscopy clearly suggested the successful fabrication of GCB (ID/IG ratio of 0.74), which was distinctively different from typical CB (ID/IG ratio of 0.91). In the modified GCB, the specific surface area (SBET) gradually increased with the reduction of pore size as a function of acetic acid content (52.97 m2/g for CB, 86.64 m2/g for GCB, 102.10-119.50 m2/g for acid-treated GCB). The uptake capability of the modified GCB (312.5 mg/g) for metal ions and organic dyes was greater than that of the unmodified GCB (161.3 mg/g) and typical CB (181.8 mg/g), presumably due to the presence of adsorbed acid. Upon testing them as adsorbents in an aqueous solution, all these carbon materials followed the Langmuir isotherm over the Freundlich model. In addition, the removal rates of cationic species (>70% removal of Cu2+ and crystal violet in 30 min) were much faster and far greater than those of anionic metanil yellow (<40% removal in 3 h), given the strong electrostatic interactions. Thus, this work demonstrates the possibility of recycling waste tires in the powder form of GCB as a cost-effective and green adsorbent that can potentially substitute traditional CB, and the modification strategy provides a proof of concept for developing simple fabrication guidelines of other carbonaceous materials. 
    more » « less
  2. ; ; ; ; ; ; ; ; ; ; et al (, Processes)
    Slag and Al/Mg oxide modified Douglas fir biochar (AMOB) were compared for their phosphate adsorbing abilities for use individually or in combination for simulated agriculture run-off remediation in wetlands. Aqueous batch and column sorption experiments were performed for both low-cost materials. AMOB was prepared in bulk using a novel green method. Material analyses included XRD, elemental analysis, SEM, EDX, and BET. Biochar and slag have different phosphate removal mechanisms. In short residence times (≤2 h), adsorption phenomena dominate for both adsorbents. Surface area likely plays a role in adsorption performance; slag was measured to be 4.1 m2/g while biochar’s surface area was 364.1 m2/g. In longer residence times (>2 h), the slow leaching of metals (Ca, Al, and Mg) from slag continue to remove phosphate through the precipitation of metal phosphates. In 24 h, slag removed more free phosphate from the solution than AMOB. Preliminary fixed bed column adsorption of slag or AMOB alone and in tandem was performed adopting a scaled-up model that can be used to remediate agricultural runoff with high phosphate content. Additionally, a desorption study was performed to analyze the efficiency of material regeneration. While AMOB does not release any adsorbed phosphates, slag slowly releases 5.7% adsorbed phosphate over seven days. 
    more » « less
  3. ; ; ; (, Journal of Hazardous, Toxic, and Radioactive Waste)
    Excessive levels of phosphate in stormwater runoff can negatively impact receiving surface water bodies, such as retention ponds, and may also seep into groundwater. Liner systems composed of materials with greater phosphate selectivity have the potential to mitigate infiltration and eliminate phosphate. One potential material is chitosan, an abundant naturally occurring biopolymer. This study evaluated five materials for their ability to remove phosphate from synthetic stormwater using batch tests with different initial phosphate concentrations ranging from 0.5 to 12 mg/L and a fixed 24-h exposure time. The materials included two types of clayey soils (kaolin and bentonite) and three different varieties of chitosan with varying molecular weights (low, medium, and high). The phosphate removal efficiency of kaolin was found to be the highest, with efficiencies ranging from 100% to 56% at different concentrations, while bentonite was found to be the least effective, with removal efficiencies ranging from 40% to 12%. The removal efficiencies of all three types of chitosans analyzed were higher than those of bentonite but lower than those of kaolin. The removal efficiencies ranged from 77% to 19% for low-molecular-weight chitosan, 84% to 31% for medium-molecular-weight chitosan, and 55% to 18% for high-molecular-weight chitosan. The removal mechanism of phosphate by kaolin and bentonite was attributed to surface adsorption and precipitation. In chitosan, the likely mechanism is electrostatic attraction. The maximum adsorption capacity for kaolin was not reached under the tested phosphate concentration range, indicating potential adsorption sites remained available on the particle surfaces. The results for bentonite, low-molecular-weight chitosan, and high-molecular-weight chitosan showed that these materials nearly reached their maximum adsorption capacities, indicating that fewer adsorption sites were remaining. The Langmuir adsorption isotherm was found to be the best-fit model for phosphate adsorption in all the materials tested compared to the Freundlich isotherm. According to the Langmuir model, the maximum adsorption capacities for kaolin, bentonite, low-molecular-weight chitosan, medium-molecular-weight chitosan, and high-molecular-weight chitosan were found to be 140.85, 33, 48.78, 82.64, and 51.28 mg/kg, respectively. 
    more » « less
  4. ; ; ; (, Fuel Cells)
    Abstract High surface area graphitic mesoporous carbons (M‐mGMC; M=Ni, Fe, Co or Ni‐Fe) were synthesizedviacatalytic graphitization using a hard template based synthesis method. In house prepared SBA‐15 silica material was impregnated with metal precursors to obtain M/SBA‐15, template for M‐mGMC synthesis. These materials were studied using different material characterization techniques, such as nitrogen adsorption desorption (BET), X‐ray diffraction (XRD) analysis, Raman spectroscopy, X‐ray photoelectron spectroscopy (XPS), Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Specific surface area ranging from 1,227.9 m2g−1to 1,320.7 m2g−1was observed for four M‐mGMCs. Raman spectroscopy, XPS and wide angle XRD suggested presence of graphitic structure in these materials along with disorders. Electrocatalytic performance of these materials along with conventional carbon black (Vulcan XC‐72) were evaluated in a single‐stack proton exchange membrane fuel cell (PEMFC). Pt/NiFe‐mGMC exhibited enhanced electrocatalytic activity compared to Pt/Ni‐mGMC, Pt/Fe‐mGMC and Pt/Co‐mGMC electrocatalysts. However, Pt/NiFe‐mGMC lacked adequate proton transport in membrane electrode assembly (MEA) compared to Pt/Vulcan XC‐72. This exploratory study showed that NiFe‐mGMC may find application as electrocatalyst support material in PEMFC. 
    more » « less
  5. ; ; ; ; ; ; ; ; ; ; et al (, Proceedings of the National Academy of Sciences)
    A continuum of water populations can exist in nanoscale layered materials, which impacts transport phenomena relevant for separation, adsorption, and charge storage processes. Quantification and direct interrogation of water structure and organization are important in order to design materials with molecular-level control for emerging energy and water applications. Through combining molecular simulations with ambient-pressure X-ray photoelectron spectroscopy, X-ray diffraction, and diffuse reflectance infrared Fourier transform spectroscopy, we directly probe hydration mechanisms at confined and nonconfined regions in nanolayered transition-metal carbide materials. Hydrophobic (K + ) cations decrease water mobility within the confined interlayer and accelerate water removal at nonconfined surfaces. Hydrophilic cations (Li + ) increase water mobility within the confined interlayer and decrease water-removal rates at nonconfined surfaces. Solutes, rather than the surface terminating groups, are shown to be more impactful on the kinetics of water adsorption and desorption. Calculations from grand canonical molecular dynamics demonstrate that hydrophilic cations (Li + ) actively aid in water adsorption at MXene interfaces. In contrast, hydrophobic cations (K + ) weakly interact with water, leading to higher degrees of water ordering (orientation) and faster removal at elevated temperatures. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email