Herein, a wavelength‐selective pyroelectric sensor based on a graphene field‐effect transistor (gFET) with a plasmon‐enhanced pyroelectric gate (PG) is reported. The PG gFET (PG‐gFET) uses a poly(vinylidene fluoride
Pyroelectric detectors are often broadband and require external filters for wavelength‐specific applications. This paper reports a tunable, narrowband, and lightweight pyroelectric infrared detector built upon a flexible membrane of As2S3−Ag−P(VDF‐TrFE) with subwavelength grating, which is capable of both on‐chip filtering and photopyroelectric energy conversion. The top surface of this hybrid membrane is a corrugated As2S3−Ag film contributing to narrowband light absorption in the near‐infrared (NIR) regime, and the bottom part is a polyvinylidene fluoride‐trifluoroethylene (PVDF‐TrFE) membrane for the conversion of the absorbed light to an electrical signal. Uniquely, applying a bias voltage to the PVDF‐TrFE membrane enables the tuning of the device's absorption and pyroelectric characteristics owing to the piezoelectrically induced mechanical bending. The resonator exhibited a resonant absorption coefficient of 80% and a full‐width‐half‐maximum of 15 nm within the NIR, a responsivity of 1.4 mV mW−1, and an equivalent noise power of 13 µW Hz−1/2at 1560 nm. By applying a 15‐V bias to the PVDF‐TrFE membrane, the absorption coefficient decreased to 18% due to the change in the grating period and incident angle. The narrowband and tunable features of the As2S3−Ag−P(VDF‐TrFE) pyroelectric detector will benefit a variety of potential applications in sensors, optical spectroscopy, and imaging.
more » « less- NSF-PAR ID:
- 10362092
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Optical Materials
- Volume:
- 9
- Issue:
- 22
- ISSN:
- 2195-1071
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
‐co ‐trifluoroethylene) or PVDF‐TrFE membrane doped with plasmonic nanoparticles as the gate. Gold nanorods (AuNRs) or silver nanoparticles (AgNPs) are incorporated into the PVDF‐TrFE membrane to enhance the photothermal conversion efficiency of PVDF‐TrFE in a specific narrowband wavelength range. The wavelength‐selective photothermal effect can optically modulate the gate potential of the PG‐gFET; this, in turn, leads to a change in current through the graphene film of the transistor. The PG‐gFET with AuNRs exhibits a maximum responsivity of 0.79 μA mW−1at the wavelength of 660 nm. Replacing AuNRs with AgNPs in the PVDF‐TrFE membrane results in tuning the plasmonic response of the transistor to 488 nm with a maximum responsivity of 0.68 μA mW−1. When plasmonic nanoparticles are absent from the PVDF‐TrFE membrane, the maximum response wavelength of the transistor is shifted to a midinfrared regime at 3125 nm, which is associated with the CC absorption of PVDF‐TrFE. The ability of the PG‐gFET to selectively respond to different light wavelengths will benefit many fields, including pyroelectric sensors, spectroscopy, and imaging. -
more » « less
Abstract Here, a wavelength‐specific photo‐thermoelectric (PTE) device is reported that achieves narrowband optical absorption and thermoelectric conversion functions using a stack of thin films on a grating‐patterned substrate. Conventional PTE devices are broadband with the absorption of electromagnetic radiation from ultraviolet to terahertz. There are demands for PTE devices that can exhibit narrowband response at a desired wavelength. Here, the narrowband PTE device consists of a photonic crystal (PC) filter with metal cladding and a thin‐film thermocouple. The PC‐PTE design is investigated numerically to illustrate the underlying energy conversion mechanism. The device is fabricated using nanoreplica molding followed by coating of thin films. The fabricated metal‐cladding PC resonator exhibits a narrowband optical absorption with a resonant absorption coefficient of 85.4% and full‐width‐half‐maximum of 14.8 nm in the visible wavelength range. The PTE measurements show that the thermoelectric output is sensitive to the coupling of incident light and guided‐mode resonance modes. Illuminated under the resonant condition, the PTE device exhibits a responsivity and noise equivalent power of 0.26 V W−1and 7.5 nW Hz−1/2, respectively. This PC‐PTE technology has the unique attributes of narrowband detection, large surface area, and low cost for the potential application in sensors, optical spectroscopy, and imaging.
-
more » « less
Abstract Flexible nanocomposite films, with cobalt ferrite nanoparticles (CFN) as the ferromagnetic component and polyvinylidene fluoride–trifluoroethylene (PVDF-TrFE) copolymer as the ferroelectric matrix, were fabricated using a blade coating technique. Nanocomposite films were prepared using a two-step process; the first process involves the synthesis of cobalt ferrite (CoFe2O4) nanoparticles using a sonochemical method, and then incorporation of various weight percentages (0, 2.5, 5, and 10%) of cobalt ferrite nanoparticles into the PVDF-TrFE to form nanocomposites. The ferroelectric polar
β phase of PVDF-TrFE was confirmed by x-ray diffraction (XRD). Thermal studies of films showed notable improvement in the thermal properties of the nanocomposite films with the incorporation of nanoparticles. The ferroelectric properties of the pure polymer/composite films were studied, showing a significant improvement of maximum polarization upon 5wt% CFN loading in PVDF-TrFE composite films compared to the PVDF-TrFE film. The magnetic properties of as-synthesized CFN and the polymer nanocomposites were studied, showing a magnetic saturation of 53.7 emu g−1at room temperature, while 10% cobalt ferrite-(PVDF-TrFE) nanocomposite shows 27.6 emu/g. We also describe a process for fabricating high optical quality pure PVDF-TrFE and pinhole-free nanocomposite films. Finally, the mechanical studies revealed that the mechanical strength of the films increases up to 5 wt% loading of the nanoparticles in the copolymer matrix and then decreases. This signifies that the obtained films could be suited for flexible electronics. -
more » « less
Abstract Inflatable structures, promising for future deep space exploration missions, are vulnerable to damage from micrometeoroid and orbital debris impacts. Polyvinylidene fluoride-trifluoroethylene (PVDF-trFE) is a flexible, biocompatible, and chemical-resistant material capable of detecting impact forces due to its piezoelectric properties. This study used a state-of-the-art material extrusion system that has been validated for in-space manufacturing, to facilitate fast-prototyping of consistent and uniform PVDF-trFE films. By systematically investigating ink synthesis, printer settings, and post-processing conditions, this research established a comprehensive understanding of the process-structure-property relationship of printed PVDF-trFE. Consequently, this study consistently achieved the printing of PVDF-trFE films with a thickness of around 40
µ m, accompanied by an impressive piezoelectric coefficient of up to 25 pC N−1. Additionally, an all-printed dynamic force sensor, featuring a sensitivity of 1.18 V N−1, was produced by mix printing commercial electrically-conductive silver inks with the customized PVDF-trFE inks. This pioneering on-demand fabrication technique for PVDF-trFE films empowers future astronauts to design and manufacture piezoelectric sensors while in space, thereby significantly enhancing the affordability and sustainability of deep space exploration missions. -
more » « less
A plasmon-enhanced pyroelectric membrane was applied to control the current flow in a graphene transistor for light detection. The graphene transistor was built on a free-standing, 15-μm-thick PVDF membrane, which was doped using gold nanorods to facilitate its optical absorption. Under the resonant condition, the device exhibited a responsivity of 0.79 μA/mW.
