Transversely curved composite shells of liquid crystal elastomer and polyethylene terephthalate with innervated electrodes present millisecond‐scale actuation with ≈200 mW electrical power inputs at low voltages (≈1 V). The molecular orientation is aligned to direct the thermomechanical work‐content to evert the native curvature. When powered, the curved structure initially remains latent and builds up strain energy. Thereafter, the work content is released in an ms‐scale impulse. The thin‐film actuators are powered against opposing loads to perform up to 10−5J of work. High speed imaging reveals tip velocities of several 100 mm s−1with powers approaching 10−4 J s−1. The design eschews bistability. After snap‐through, when the power is off, the actuator spontaneously resets to its native state. The actuation profiles are functions of the geometry and the electrical pulse patterns. The latency of actuation is reduced by powering the actuators with pulses that trigger snap‐through, allow its reset to the native state, but prevent its cooling to the ambient before subsequent actuation cycles. The actuation is harnessed in sub‐gram scale robots, including water‐strider mimicking configurations and steerable robots that can navigate on compliant (sand) and hard (slippery) surfaces. A viable template for impulsive actuation using frugal electrical power emerges.
Open-channel microfluidics enables precise positioning and confinement of liquid volume to interface with tightly integrated optics, sensors, and circuit elements. Active actuation via electric fields can offer a reduced footprint compared to passive microfluidic ensembles and removes the burden of intricate mechanical assembly of enclosed systems. Typical systems actuate via manipulating surface wettability (
- Award ID(s):
- 2011401
- NSF-PAR ID:
- 10365267
- Publisher / Repository:
- Nature Publishing Group
- Date Published:
- Journal Name:
- Nature Communications
- Volume:
- 13
- Issue:
- 1
- ISSN:
- 2041-1723
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
more » « less
Abstract Surface recombination is a major bottleneck for realizing highly efficient micro/nanostructure solar cells. Here, parametric studies of the influence of Si microwire (SiMW) surface‐facet orientation (rectangular with flat‐facets, {110}, {100} and circular), with a fixed height of 10 µm, diameter (
D = 1.5–9.5 µm), and sidewall spacing (S = 2.5–8.5 µm), and mesh‐grid density (1–16 mm−2) on recombination and carrier collection in SiMW solar cells with radial p‐n junctions are reported. An effective surface passivation layer composed of thin thermally grown silicon dioxide (SiO2) and silicon nitride (SiNx ) layers is employed. For a fixedD of 1.5 µm, tight SiMW spacing results in improved short‐circuit current density (J sc= 30.1 mA cm−2) and sparse arrays result in open‐circuit voltages (V oc= 0.552 V) that are similar to those of control Si planar cells. For a fixedS , smallerD results in better light trapping at shorter wavelengths and higherJ scwhile largerD exhibits better light trapping at larger wavelengths and a higherV oc. With a mesh‐grid electrode the power conversion efficiency increases to 15.3%. These results provide insights on the recombination mechanisms in SiMW solar cells and provide general design principles for optimizing their performance. -
more » « less
Abstract Crosslinked polymers and gels are important in soft robotics, solar vapor generation, energy storage, drug delivery, catalysis, and biosensing. However, their attractive mass transport and volume‐changing abilities are diffusion‐limited, requiring miniaturization to avoid slow response. Typical approaches to improving diffusion in hydrogels sacrifice mechanical properties by increasing porosity or limit the total volumetric flux by directionally confining the pores. Despite tremendous efforts, simultaneous enhancement of diffusion and mechanical properties remains a long‐standing challenge hindering broader practical applications of hydrogels. In this work, cononsolvency photopolymerization is developed as a universal approach to overcome this swelling–mechanical property trade‐off. The as‐synthesized poly(
N ‐isopropylacrylamide) hydrogel, as an exemplary system, presents a unique open porous network with continuous microchannels, leading to record‐high volumetric (de)swelling speeds, almost an order of magnitude higher than reported previously. This swelling enhancement comes with a simultaneous improvement in Young's modulus and toughness over conventional hydrogels fabricated in pure solvents. The resulting fast mass transport enables in‐air operation of the hydrogel via rapid water replenishment and ultrafast actuation. The method is compatible with 3D printing. The generalizability is demonstrated by extending the technique to poly(N ‐tertbutylacrylamide‐co‐ polyacrylamide) and polyacrylamide hydrogels, non‐temperature‐responsive polymer systems, validating the present hypothesis that cononsolvency is a generic phenomenon driven by competitive adsorption. -
more » « less
We demonstrate the implementation of a low-power, low-profile, varifocal liquid-crystal Fresnel lens stack suitable for tunable imaging in smart contact lenses. The lens stack consists of a high-order refractive-type liquid crystal Fresnel chamber, a voltage-controlled twisted nematic cell, a linear polarizer and a fixed offset lens. The lens stack has an aperture of 4 mm and thickness is ∼980 µm. The varifocal lens requires ∼2.5 VRMSfor a maximum optical power change of ∼6.5 D consuming electrical power of ∼2.6 µW. The maximum RMS wavefront aberration error was 0.2 µm and the chromatic aberration was 0.008 D/nm. The average BRISQUE image quality score of the Fresnel lens was 35.23 compared to 57.23 for a curved LC lens of comparable power indicating a superior Fresnel imaging quality.
-
more » « less
Abstract An electrical‐biased or mechanical‐loaded scanning probe written on the ferroelectric surface can generate programmable domain nanopatterns for ultra‐scaled and reconfigurable nanoscale electronics. Fabricating ferroelectric domain patterns by direct‐writing as quickly as possible is highly desirable for high response rate devices. Using monolayer
α ‐In2Se3ferroelectric with ≈1.2 nm thickness and intrinsic out‐of‐plane polarization as an example, a writing‐speed dependent effect on ferroelectric domain switching is discovered. The results indicate that the threshold voltages and threshold forces for domain switching can be increased from −4.2 to −5 V and from 365 to 1216 nN, respectively, as the writing‐speed increases from 2.2 to 10.6 µm s−1. The writing‐speed dependent threshold voltages can be attributed to the nucleations of reoriented ferroelectric domains, in which sufficient time is needed for subsequent domain growth. The writing‐speed dependent threshold forces can be attributed to the flexoelectric effect. Furthermore, the electrical‐mechanical coupling can be employed to decrease the threshold force, achieving as low as ≈189±41 nN, a value smaller than those of perovskite ferroelectric films. Such findings reveal a critical issue of ferroelectric domain pattern engineering that should be carefully addressed for programmable direct‐writing electronics applications.
