skip to main content

Attention:

The NSF Public Access Repository (NSF-PAR) system and access will be unavailable from 11:00 PM ET on Thursday, October 10 until 2:00 AM ET on Friday, October 11 due to maintenance. We apologize for the inconvenience.


Title: Thermoelectric energy harvesting for wireless onboard rail condition monitoring
A thermoelectric energy harvesting device is evaluated to power a bearing health monitoring system. Unlike wayside equipment, the new system is an onboard wireless solution utilizing accelerometer and temperature sensors to assess the bearing condition continuously. The harvesting system consists of two thermoelectric generator modules with aluminium heat sinks, a switching boost converter, a battery management circuit, and a lithium rechargeable battery. The performance of the harvester is validated on an AAR class bearing mounted on a laboratory tester, with load and speed simulating common freight routes of up to 896 miles. The energy harvested varies with operating conditions, and data is presented showing the effect of load and speed. Over a realistic route, the net energy harvested is more than double that needed to indefinitely power a Bluetooth Low Energy sensor. The critical design parameters are the ratio of open-circuit voltage to the temperature difference for the thermoelectric module, and the cold start voltage of the boost converter.  more » « less
Award ID(s):
2112650
NSF-PAR ID:
10417517
Author(s) / Creator(s):
; ; ; ;
Date Published:
Journal Name:
International Journal of Rail Transportation
ISSN:
2324-8378
Page Range / eLocation ID:
1 to 18
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. This paper presents a step-up DC-DC converter that uses a stepwise gate-drive technique to reduce the power FET gate-drive energy by 82%, allowing positive efficiency down to an input voltage of ±0.5 mV—the lowest input voltage ever achieved for a DC-DC converter as far as we know. Below ±0.5 mV the converter automatically hibernates, reducing quiescent power consumption to just 255 pW. The converter has an efficiency of 63% at ±1 mV and 84% at ±6 mV. The input impedance is programmable from 1 Ω to 600 Ω to achieve maximum power extraction. A novel delay line circuit controls the stepwise gatedrive timing, programmable input impedance, and hibernation behavior. Bipolar input voltage is supported by using a flyback converter topology with two secondary windings. A generated power good signal enables the load when the output voltage has charged above 2.7 V and disables when the output voltage has discharged below 2.5 V. The DC-DC converter was used in a thermoelectric energy harvesting system that effectively harvests energy from small indoor temperature fluctuations of less than 1°C. Also, an analytical model with unprecedented accuracy of the stepwise gate-drive energy is presented. 
    more » « less
  2. null (Ed.)
    This paper presents the integration of an AC-DC rectifier and a DC-DC boost converter circuit designed in 180 nm CMOS process for ultra-low frequency (<; 10 Hz) energy harvesting applications. The proposed rectifier is a very low voltage CMOS rectifier circuit that rectifies the low-frequency signal of 100-250 mV amplitude and 1-10 Hz frequency into DC voltage. In this work, the energy is harvested from the REWOD (reverse electrowetting-on-dielectric) generator, which is a reverse electrowetting technique that converts mechanical vibrations to electrical energy. The objective is to develop a REWOD-based self-powered motion (such as walking, running, jogging, etc.) tracking sensors that can be worn, thus harvesting energy from regular activities. To this end, the proposed circuits are designed in such a way that the output from the REWOD is rectified and regulated using a DC-DC converter which is a 5-stage cross-coupled switching circuit. Simulation results show a voltage range of 1.1 V-2.1 V, i.e., 850-1200% voltage conversion efficiency (VCE) and 30% power conversion efficiency (PCE) for low input signal in the range 100-250 mV in the low-frequency range. This performance verifies the integration of the rectifier and DC-DC boost converter which makes it highly suitable for various motion-based energy harvesting applications. 
    more » « less
  3. null (Ed.)
    There is an ongoing trend to increasingly offload inference tasks, such as CNNs, to edge devices in many IoT scenarios. As energy harvesting is an attractive IoT power source, recent ReRAM-based CNN accelerators have been designed for operation on harvested energy. When addressing the instability problems of harvested energy, prior optimization techniques often assume that the load is fixed, overlooking the close interactions among input power, computational load, and circuit efficiency, or adapt the dynamic load to match the just-in-time incoming power under a simple harvesting architecture with no intermediate energy storage. Targeting a more efficient harvesting architecture equipped with both energy storage and energy delivery modules, this paper is the first effort to target whole system, end-to-end efficiency for an energy harvesting ReRAM-based accelerator. First, we model the relationships among ReRAM load power, DC-DC converter efficiency, and power failure overhead. Then, a maximum computation progress tracking scheme ( MaxTracker ) is proposed to achieve a joint optimization of the whole system by tuning the load power of the ReRAM-based accelerator. Specifically, MaxTracker accommodates both continuous and intermittent computing schemes and provides dynamic ReRAM load according to harvesting scenarios. We evaluate MaxTracker over four input power scenarios, and the experimental results show average speedups of 38.4%/40.3% (up to 51.3%/84.4%), over a full activation scheme (with energy storage) and order-of-magnitude speedups over the recently proposed (energy storage-less) ResiRCA technique. Furthermore, we also explore MaxTracker in combination with the Capybara reconfigurable capacitor approach to offer more flexible tuners and thus further boost the system performance. 
    more » « less
  4. null (Ed.)
    This paper presents a circuit for simultaneous reception of optical power and data using a solar cell. The circuit employs a switched-inductor boost DC-DC converter for energy harvesting and a low-power thresholding receiver for data reception. The thresholding data receiver comprises a current-sense resistor that monitors the current output of the solar cell, an instrumentation amplifier, a band-pass filter and a comparator. A system-level analysis of an optical communication system employing the proposed circuit is presented along with a circuit-level analysis and implementation. As a proof-of-concept, the proposed circuit for simultaneous power and data reception is implemented using off-the-shelf components and tested using a custom-built test setup. Measurement results, including harvested power, electronic noise and bit error rate (BER), are reported for a GaAs solar cell and a red LED light source. Results show that 223 μW of power are harvested by the DC-DC converter at a distance of 32.5 cm and a radiated power of 9.3 mW. At a modulation depth of 50% and a transmission speed of 2.5 kbps, a BER of 1.008×10^-3 is achieved. Measurement results reveal that the proposed solution exhibits a trade-off between harvested power, transmission speed and BER. 
    more » « less
  5. The proposed circuit aims to harvest energy from body heat, in which the thermal gradient is only a few degrees. The boost converter operating in a burst mode offers a high conversion ratio while minimizing power loss. Maximum power point tracking based on the fractional open circuit voltage method ensures that the proposed circuit can be applied for a variety of thermoelectric generators (TEGs) and TEG setups. The proposed circuit is designed and laid out in CMOS 0.25 μm technology. Post layout simulation results indicate the converter is able to boost input voltages as low as 50 mV to the regulated output of 3 V, while achieving peak efficiency of 81%. 
    more » « less