skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Microfluidic thermal flow sensor based on phase-change material with ultra-high thermal sensitivity
A microfluidic thermal mass flow sensor based on planar micro-machining technology and a phase-change material is designed, fabricated, and characterized. The sensor configuration uses a small patch of vanadium dioxide (VO 2 ) thin film as the sensing element closely placed in the down streaming direction of the heat source. By operating the VO 2 sensor in the phase transition region, no thermal insulation structure is required due to the ultra-high thermal sensitivity in this region. The characteristic 3-order resistance change, from 290 kΩ to 290 Ω, is observed during the full heating and cooling cycles by using both substrate heating and resistive heating methods. The equivalent maximum temperature coefficient of resistance (TCR) is calculated to be −0.37 K −1 in the cooling cycle and −0.43 K −1 in the cooling and heating cycle, respectively. The sensing operation principle is determined to follow the major cooling curve to avoid falling into minor loops and to secure high TCR. The resistance of VO 2 is monitored under flow rates ranging from 0 to 37.8 μL s −1 with the maximum sensitivity of 1.383%/(μL min −1 ). The studies presented in this research may enable the application of utilizing nonlinear metamaterial in microfluidic flow sensors with orders of magnitude improvement in sensitivity.  more » « less
Award ID(s):
1854750
PAR ID:
10417636
Author(s) / Creator(s):
; ;
Date Published:
Journal Name:
Journal of Materials Chemistry C
Volume:
11
Issue:
4
ISSN:
2050-7526
Page Range / eLocation ID:
1278 to 1284
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; (, Nanophotonics)
    Abstract Switchable radiative cooling based on the phase-change material vanadium dioxide (VO2) automatically modulates thermal emission in response to varying ambient temperature. However, it is still challenging to achieve constant indoor temperature control solely using a VO2-based radiative cooling system, especially at low ambient temperatures. Here, we propose a reverse-switching VO2-based radiative cooling system, assisting indoor air conditioning to obtain precise indoor temperature control. Unlike previous VO2-based radiative cooling systems, the reverse VO2-based radiative cooler turns on radiative cooling at low ambient temperatures and turns off radiative cooling at high ambient temperatures, thereby synchronizing its cooling modes with the heating and cooling cycles of the indoor air conditioning during the actual process of precise temperature control. Calculations demonstrate that our proposed VO2-based radiative cooling system significantly reduces the energy consumption by nearly 30 % for heating and cooling by indoor air conditioning while maintaining a constant indoor temperature, even surpassing the performance of an ideal radiative cooler. This work advances the intelligent thermal regulation of radiative cooling in conjunction with the traditional air conditioning technology. 
    more » « less
  2. ; ; (, 2020 19th IEEE Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems (ITherm))
    During air or liquid cooling, thermal resistance of the devices is measured precisely from the thermal information at the junction. But existing thermal measurement technologies fall short because of highly transient events such as unstable vortex formation (air cooling) and bubble growth (two-phase liquid cooling). In solving this problem, this paper reports a novel and low-cost thermal mapping technique that can capture highly spatio-temporal temperature evolution at the solid-liquid interface. Essentially, a robust interface is fabricated with CuInS 2 /ZnS Quantum dots (λ peak = 550 nm and 750 nm) trapped inside nanopores (20 nm-30 nm) of a ceramic membrane (50 μm) and/or everyday use paper. It is observed that such nanoconfinement assisted Quantum dots provided sustained thermal photoluminescence coefficient (-0.1 nm/°C) at high number of heating-cooling cycle. This unique yet low cost thermal mapping technique is applied to capture thermal evolution during micro-droplet impingement cooling and hemiwicking flows through anisotropic wicks which showcase commendable spatio-temporal benefits. 
    more » « less
  3. ; ; ; (, IEEE Journal of Photovoltaics)
    Abstract—Unlike the traditional tube-furnace annealing at 875 °C, rapid thermal annealing (RTA) and laser annealing offer flexibility, high throughput, and control of the heating and cooling rates and holding times for effective crystallization, dopant activation, and passivation quality in the B-doped p-TOPCon device. A comprehensive scientific understanding of the effects of RTA is required. Slower RTA heating (≤ 798 K/min) and cooling (≤ 156 K/min) rates and optimal 60 s holding time at 825 °C enhanced the passivation quality, which was further improved by post anneal forming gas annealing (FGA). Faster heating and cooling rates (≥ 4800 K/min) damaged the passivation quality irreversibly and did not improve further by FGA. The optimized RTA parameters yielded iVoc of 638 mV and sheet resistance of ∼1.0 kΩ/sq. The dopant activation was independent of the heating and cooling rates. 
    more » « less
  4. ; ; ; ; ; ; ; (, Advanced Electronic Materials)
    Abstract Vanadium Dioxide (VO2) is a material that exhibits a phase transition from an insulating state to a metallic state at ≈68 °C. During a temperature cycle consisting of warming followed by cooling, the resistivity of VO2changes by several orders of magnitude over the course of the hysteresis loop. Using a focused laser beam (λ = 532 nm), it is shown that it is possible to optically generate micron‐sized metallic patterns within the insulating phase of a VO2planar junction which can be used to tune, on demand, the resistance of the VO2junction. A resistor network simulation is used to characterize the resulting resistance drops in the devices. These patterns persist while the base temperature is held constant within the hysteretic region while being easily removed totally by simply lowering the base temperature. Surprisingly, it is also observed that the pattern can be partially erased using an atomic force microscope (AFM) tip on the submicron scale. This erasing process can be qualitatively explained by the temperature difference between the VO2surface and the tip which acts as a local cooler. This optical and AFM resistive fine‐tuning offers the possibility of creating controllable synaptic weights between room‐temperature VO2neuristors. 
    more » « less
  5. ; ; (, Geotechnical Testing Journal)
    ABSTRACT This study investigates linkages between volume change, pore fluid drainage, shear wave velocity, and temperature of soft clays using a thermal triaxial cell equipped with bender elements, a measurement approach that has not been explored widely in past thermo-mechanical studies. Two kaolinite specimens were consolidated mechanically to a normally consolidated state and then subjected to drained and undrained heating-cooling cycles, respectively. After cooling, the specimens were subjected to further mechanical consolidation to evaluate changes in apparent preconsolidation stress. Both specimens showed net contractive thermal strains after a heating-cooling cycle and overconsolidated behavior during mechanical compression immediately after cooling. The shear wave velocity increased during drained heating, but negligible changes were observed during drained cooling, indicating permanent hardening because of thermal consolidation during the heating-cooling cycle. The shear wave velocity decreased during undrained heating because of a reduction in effective stress associated with thermal pressurization of the pore fluid but subsequently increased when drainage was permitted at elevated temperature. The shear wave velocity increased slightly during undrained cooling but decreased when drainage was permitted at room temperature. Net increases in small-strain shear modulus of 17 and 11 % after heating-cooling cycles under drained and undrained (with drainage after reaching stable temperatures) conditions, respectively, provide further evidence to the potential of thermal soil improvement of normally consolidated clays. Transient changes in shear modulus also highlight the importance of considering drainage conditions and corresponding changes in effective stress state during heating-cooling cycles. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email