Accurate knowledge of transmission line parameters is essential for a variety of power system monitoring, protection, and control applications. The use of phasor measurement unit (PMU) data for transmission line parameter estimation (TLPE) is well-documented. However, existing literature on PMU-based TLPE implicitly assumes the measurement noise to be Gaussian. Recently, it has been shown that the noise in PMU measurements (especially in the current phasors) is better represented by Gaussian mixture models (GMMs), i.e., the noises are non-Gaussian. We present a novel approach for TLPE that can handle non-Gaussian noise in the PMU measurements. The measurement noise is expressed as a GMM, whose components are identified using the expectation-maximization (EM) algorithm. Subsequently, noise and parameter estimation is carried out by solving a maximum likelihood estimation problem iteratively until convergence. The superior performance of the proposed approach over traditional approaches such as least squares and total least squares as well as the more recently proposed minimum total error entropy approach is demonstrated by performing simulations using the IEEE 118-bus system as well as proprietary PMU data obtained from a U.S. power utility.
more »
« less
Transmission Line Parameter Estimation Under Non-Gaussian Measurement Noise
Accurate knowledge of transmission line parameters is essential for a variety of power system monitoring, protection, and control applications. The use of phasor measurement unit (PMU) data for transmission line parameter estimation (TLPE) is well-documented. However, existing literature on PMU-based TLPE implicitly assumes the measurement noise to be Gaussian. Recently, it has been shown that the noise in PMU measurements (especially in the current phasors) is better represented by Gaussian mixture models (GMMs), i.e., the noises are non-Gaussian. We present a novel approach for TLPE that can handle non-Gaussian noise in the PMU measurements. The measurement noise is expressed as a GMM, whose components are identified using the expectation-maximization (EM) algorithm. Subsequently, noise and parameter estimation is carried out by solving a maximum likelihood estimation problem iteratively until convergence. The superior performance of the proposed approach over traditional approaches such as least squares and total least squares as well as the more recently proposed minimum total error entropy approach is demonstrated by performing simulations using the IEEE 118-bus system as well as proprietary PMU data obtained from a U.S. power utility.
more »
« less
- NSF-PAR ID:
- 10435131
- Date Published:
- Journal Name:
- IEEE transactions on power systems
- ISSN:
- 0885-8950
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
The state estimation (SE) has been widely used in power system control centers to optimally estimate the states of the power grid in real time. Using different objective functions, many SE algorithms have been proposed to filter out measurement noise in different ways. In this paper, three widely-used SE algorithms, i.e., the weighted least squares (WLS), least absolute value (LAV), and projection statistics (PS) based algorithms, are compared in their estimation accuracy and computation time. The comparison was made using the simulation data generated from the IEEE 14-bus system and IEEE 118-bus system through the Monte-Carlo method. It is found that when the measurement noise is reasonably small and follows the independent Gaussian distribution, the WLS algorithm has the best accuracy and shortest computation time. When some measurements at leverage points were compromised by outliers, the PS based algorithm is the most robust among the three methods. The study results can be used to assist control centers in choosing the right SE algorithm based on the features of the measurement noise and setup.more » « less
-
ION ITM (Ed.)This paper describes the development, implementation, and testing of a GNSS jammer localizer using power measurement profiles collected during un-crewed aerial system (UAS) fly-bys. A linearized measurement equation based on the Friis power transmission formula is derived in which RF channel propagation parameters are grouped into a single parameter for estimation. Synchronized power and UAS position measurements are processed in a batch-type sequential non-linear least squares algorithm for simultaneous estimation of static jammer position and received power model parameters. We develop a low size, weight, power, and cost (SWAP-C) quad-rotor UAS test bed that can collect and time-stamp power measurements with UAS position. Since GNSS jamming is illegal, a LoRa 868 MHz transmitter is used as a surrogate GNSS jammer during field testing – providing Received Signal Strength Indicator (RSSI) measurements to the LoRa receiver onboard the UAS. Testing is conducted at the Virginia Tech Kentland Experimental Aerial Systems Lab, where emitter localization is evaluated for three different trajectories. Experimental performance analysis suggests that meter-level localization accuracy is achievable with prior knowledge on source location and by accounting for antenna gain pattern variations over time in the estimation process with a first order Gauss Markov Process.more » « less
-
more » « less
Abstract This paper addresses the parameter estimation problem for lithium-ion battery pack models comprising cells in series. This valuable information can be exploited in fault diagnostics to estimate the number of cells that are exhibiting abnormal behaviour, e.g. large resistances or small capacities. In particular, we use a Bayesian approach to estimate the parameters of a two-cell arrangement modelled using equivalent circuits. Although our modeling framework has been extensively reported in the literature, its structural identifiability properties have not been reported yet to the best of the authors’ knowledge. Moreover, most contributions in the literature tackle the estimation problem through point-wise estimates assuming Gaussian noise using e.g. least-squares methods (maximum likelihood estimation) or Kalman filters (maximum a posteriori estimation). In contrast, we apply methods that are suitable for nonlinear and non-Gaussian estimation problems and estimate the full posterior probability distribution of the parameters. We study how the model structure, available measurements and prior knowledge of the model parameters impact the underlying posterior probability distribution that is recovered for the parameters. For two cells in series, a bimodal distribution is obtained whose modes are centered around the real values of the parameters for each cell. Therefore, bounds on the model parameters for a battery pack can be derived.
-
Fluorescently labeled proteins absorb and emit light, appearing as Gaussian spots in fluorescence imaging. When fluorescent tags are added to cytoskeletal polymers such as microtubules, a line of fluorescence and even non-linear structures results. While much progress has been made in techniques for imaging and microscopy, image analysis is less well-developed. Current analysis of fluorescent microtubules uses either manual tools, such as kymographs, or automated software. As a result, our ability to quantify microtubule dynamics and organization from light microscopy remains limited. Despite the development of automated microtubule analysis tools for in vitro studies, analysis of images from cells often depends heavily on manual analysis. One of the main reasons for this disparity is the low signal-to-noise ratio in cells, where background fluorescence is typically higher than in reconstituted systems. Here, we present the Toolkit for Automated Microtubule Tracking (TAMiT), which automatically detects, optimizes, and tracks fluorescent microtubules in living yeast cells with sub-pixel accuracy. Using basic information about microtubule organization, TAMiT detects linear and curved polymers using a geometrical scanning technique. Images are fit via an optimization problem for the microtubule image parameters that are solved using non-linear least squares in Matlab. We benchmark our software using simulated images and show that it reliably detects microtubules, even at low signal-to-noise ratios. Then, we use TAMiT to measure monopolar spindle microtubule bundle number, length, and lifetime in a large dataset that includes several S. pombe mutants that affect microtubule dynamics and bundling. The results from the automated analysis are consistent with previous work and suggest a direct role for CLASP/Cls1 in bundling spindle microtubules. We also illustrate automated tracking of single curved astral microtubules in S. cerevisiae, with measurement of dynamic instability parameters. The results obtained with our fully-automated software are similar to results using hand-tracked measurements. Therefore, TAMiT can facilitate automated analysis of spindle and microtubule dynamics in yeast cells.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- The DOI is not currently available.
