An official website of the United States government
Cold sintering of surface‐modified iron compacts results in a co‐continuous phosphate interphase between iron particles that provide both enhanced green strength and green density similar to the process that has been successfully introduced in low‐temperature densification of ceramic materials. Relative density as high as 95% along with transverse rupture strength of ≈ 75 MPa, which is almost six times that of conventional powdered metal iron compact and 2.5 times that of warm compacted controls, is achieved. Dilatometry study at different pressures shows a small but significant improvement in densification process during cold sintering relative to the larger densification of warm compacted control. Strength model based on microstructural analysis as well as in situ diffused reflectance infrared Fourier transform spectroscopy (DRIFTS) experiments reveals the nature of the interphase that imparts the large cohesive strength under the cold sintered assisted warm compaction. The process is conducive to produce iron compacts for green machining. Furthermore, the samples when subjected to high‐temperature sintering yield a fully sintered iron compact with density > 7.2 g cm−3and transverse rupture strength as high as 780 MPa. All in all, there are major new opportunities with the cold sintered assisted warm compaction of powdered metals that will also be discussed.
more »
« less
Comparison of different sintering aids in cold sinter‐assisted densification of lead zirconate titanate
Abstract Ceramics such as lead zirconate titanate (PZT) tend to dissolve incongruently, and thus pose a challenge in the cold sintering process. Moist lead nitrate has previously been shown to enable a cold sinter‐assisted densification of PZT by a viscous phase sintering mechanism. In this paper, lead acetate trihydrate is demonstrated to lower the required temperature of the cold sintering step to 200°C. This densification process was described as a two‐step process: cold sintering of PZT with lead acetate trihydrate and post‐annealing the as‐cold sintered PZT ceramics. Unlike in the case of lead nitrate, PZT densification with lead acetate trihydrate occurs by a liquid phase assisted sintering mechanism, leading to an as‐cold sintered relative density of 84% at 200°C. After performing a post‐anneal step at 900°C, >97% relative densities were achieved in samples that were cold sintered with lead acetate trihydrate. This step not only densified PZT but also refined the grain boundaries. In the post‐annealed samples, the room‐temperature relative permittivity at 100 Hz was ~1600, slightly higher than that reported in samples that used lead nitrate as a sintering aid; the loss tangent was about 3.8%. For measurements at 10 Hz, the remanent polarization in both cases was ~28 µC/cm2. Both Rayleigh analysis and aging studies showed that a higher irreversible contribution to the permittivity exists in samples that used lead nitrate as a cold sintering aid.
more »
« less
- PAR ID:
- 10450163
- Publisher / Repository:
- Wiley-Blackwell
- Date Published:
- Journal Name:
- Journal of the American Ceramic Society
- Volume:
- 104
- Issue:
- 11
- ISSN:
- 0002-7820
- Format(s):
- Medium: X Size: p. 5479-5488
- Size(s):
- p. 5479-5488
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Medical ultrasound and other devices that require transducer arrays are difficult to manufacture, particularly for high frequency devices (>30 MHz). To enable focusing and beam steering, it is necessary to reduce the center-to-center element spacing to half of the acoustic wavelength. Conventional methodologies prevent co-sintering ceramic–polymer composites due to the low decomposition temperatures of the polymer. Moreover, for ultrasound transducer arrays exceeding 30 MHz, methods such as dice-and-fill cannot provide the dimensional tolerances required. Other techniques in which the ceramic is formed in the green state often fail to retain the required dimensions without distortion on firing the ceramic. This paper explores the use of the cold sintering process to produce dense lead zirconate titanate (PZT) ceramics for application in high frequency transducer arrays. PZT–polymer 2-2 composites were fabricated by cold sintering tape cast PZT with Pb nitrate as a sintering aid and ZnO as the sacrificial layer. PZT beams of 35 μm width with ~5.4 μm kerfs were produced by this technique. The ZnO sacrificial layer was also found to serve as a liquid phase sintering aid that led to grain growth in adjacent PZT. This composite produced resonance frequencies of >17 MHz.more » « less
-
Abstract This study explores cold sintering of naturally occurring minerals as supplementary cementitious materials (SCM) or cement analogs, which have the potential to transform the traditional high‐energy, high‐emission cement manufacturing pathways. Diopside (MgCaSi2O6), a natural inosilicate, is used as the model system. As diopside is hard for cold sintering directly (by itself), this study demonstrates that the addition of amorphous silica nanoparticles can enable cold sintering of diopside. The cold‐sintered diopside–silica composites are characterized by X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. The effect of the relative weight percentage of silica added is examined. The relative density of the cold‐sintered composite reaches nearly 90% at 400 MPa and 200°C in 60 min. For specimens with the addition of 30 wt% or more of amorphous SiO2, cold sintering also induces partial crystallization, converting a fraction of amorphous silica to quartz. The crystallization kinetics exhibits a stochastic nature. The Vickers hardness of the cold‐sintered diopside–silica composite increases with increasing amount of silica, whichpromotes cold sintering, reaching ∼3 GPa with 20 wt% or more silica. The diopside–silica composites studied here serve as a model system for metal‐leached silicate mine tailings, which are expected to have nanoporous amorphous silica shells on silicate particles to enable the silica‐assisted cold sintering mechanism discovered in this study.more » « less
-
The densification and sintering of ceramics using microwaves is first reported in the mid‐1960s. Today, the reduced carbon footprint of this process has renewed interest as it uses less energy overall compared to conventional process heating/furnaces. However, scaling up and commercializing the microwave sintering process of ceramics remains a formidable challenge. As a contactless method, microwave sintering offers geometric flexibility over other field‐assisted sintering processes. Yet, the inability to address multiscale, multiphysics‐driven heterogeneities arising during microwave coupling limits discussions about a future scale‐up process. Herein, the case is made that unlike 60 years ago, new advances in multiscale computational modeling, materials characterization, control systems, and software open up new avenues for addressing these challenges. More importantly, the rise of additive manufacturing techniques demands the innovation of sintering processes in the ceramics community for realizing near‐net‐shaped and complex parts for applications ranging from medical implants to automotive and aerospace parts.more » « less
-
Cold sintering is an unusually low-temperature process that uses a transient transport phase, which is most often liquid, and an applied uniaxial force to assist in densification of a powder compact. By using this approach, many ceramic powders can be transformed to high-density monoliths at temperatures far below the melting point. In this article, we present a summary of cold sintering accomplishments and the current working models that describe the operative mechanisms in the context of other strategies for low-temperature ceramic densification. Current observations in several systems suggest a multiple-stage densification process that bears similarity to models that describe liquid phase sintering. We find that grain growth trends are consistent with classical behavior, but with activation energy values that are lower than observed for thermally driven processes. Densification behavior in these low-temperature systems is rich, and there is much to be investigated regarding mass transport within and across the liquid-solid interfaces that populate these ceramics during densification. Irrespective of mechanisms, these low temperatures create a new opportunity spectrum to design grain boundaries and create new types of nanocomposites among material combinations that previously had incompatible processing windows. Future directions are discussed in terms of both the fundamental science and engineering of cold sintering.more » « less
