An official website of the United States government
The sensitivity of recrystallization kinetics in metals to the heterogeneity of microstructure and deformation history is a widely accepted experimental fact. However, most of the available recrystallization models employ either a mean field approach or use grain-averaged parameters, and thus neglecting the mesoscopic heterogeneity induced by prior deformation. In the present study, we investigate the impact of deformation-induced dislocation (subgrain) structure on the kinetics of recrystallization in metals using the phase-field approach. The primary focus here is upon the role of dislocation cell boundaries. The free energy formulation of the phase-field model accounts for the heterogeneity of the microstructure by assigning localized energy to the resulting dislocation microstructure realizations generated from experimental data. These microstructure realizations are created using the universal scaling laws for the spacing and the misorientation angles of both the geometrically necessary and incidental dislocation boundaries. The resulting free energy is used into an Allen-Cahn based model of recrystallization kinetics, which are solved using the finite element method. The solutions thus obtained shed light on the critical role of the spatial heterogeneity of deformation in the non-smooth growth of recrystallization nuclei and on the final grain structure. The results showed that, in agreement with experiment, the morphology of recrystallization front exhibits protrusions and retrusions. By resolving the subgrain structure, the presented algorithm paves the way for developing predictive kinetic models that fully account for the deformed state of recrystallizing metals.
more »
« less
Field fluctuations viscoplastic self-consistent crystal plasticity: Applications to predicting texture evolution during deformation and recrystallization of cubic polycrystalline metals
Recent advances pertaining to modeling of grain fragmentation during deformation and recrystallization of polycrystalline metals using viscoplastic self-consistent (VPSC) polycrystal plasticity are combined into a field fluctuations VPSC (FF-VPSC) model. The FF-VPSC model is a higher-order formulation calculating the second moments of lattice rotation rates based on the second moments of stress fields inside grains and resulting intragranular misorientation distributions. The misorientation distributions are used to define a grain fragmentation sub-model for improving predictions of deformation texture evolution and to formulate kinetics sub-models for nucleation as well as to influence the stored energy governing grain growth for the predictions of recrystallization texture evolution. Formation of a copper-like texture in moderately high stacking fault energy (SFE) Cu and a brass-like texture in low SFE brass during rolling to very large strains are successfully predicted using the model. Remarkably, the model also predicts recrystallization textures from the deformation textures of the two metals after adjusting tradeoffs between transition-bands and grain boundary nucleation mechanisms. Additionally, rolling and recrystallization of an interstitial-free steel, tension and recrystallization of AA5182-O, and recrystallization of an additively manufacturing cobalt-based alloy MarM-509 are simulated to predict texture evolution. Through these case studies involving multiple alloys and thermo-mechanical processes we show that, in addition to being predictive with good accuracy, the key advantage of the model lies in its versatility. The FF-VPSC model, simulation results, and insights from the results are presented and discussed in this paper.
more »
« less
- Award ID(s):
- 1757371
- PAR ID:
- 10468714
- Publisher / Repository:
- Elsevier
- Date Published:
- Journal Name:
- Acta Materialia
- Volume:
- 261
- Issue:
- C
- ISSN:
- 1359-6454
- Page Range / eLocation ID:
- 119395
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Syntectonic microstructural evolution is a well‐known phenomenon in the mantle and lower crust associated with two main processes: grain size reduction through dynamic recrystallization and development of crystallographic preferred orientation (CPO). However, the effects of annealing via static recrystallization on grain size and CPO have been largely overlooked. We investigated mantle annealing by analyzing a suite of kimberlite‐hosted garnet peridotite xenoliths from the Wyoming Craton. We focus on five xenoliths that show microstructures reflecting different degrees of recrystallization, with annealed grains characterized by distinctive faceted boundaries crosscutting surrounding, nonfaceted matrix grains. These textures are indicative of discontinuous static recrystallization (DiSRX). Electron backscatter diffraction analysis further demonstrates a ∼10°–20° misorientation between DiSRXed grains and the matrix grains, resulting in an overall weaker CPO. These characteristics are remarkably similar to microstructures observed in samples that were annealed after deformation in the laboratory. Measurements of the thermal conditions and water contents associated with the last equilibration of the xenoliths suggests that high homologous temperatures (T/Tm > 0.9) are necessary to induce DiSRX. We postulate that annealing through DiSRX occurs under high temperatures after a short episode of intense deformation (years to hundreds of years) with timescales for annealing estimated as weeks to years, significantly slower than the timescale of hours expected for a kimberlitic magma ascent. We conclude that microstructural transformation due to DiSRX will occur during transient heating events associated with mantle upwelling, plumes, and lithospheric thinning.more » « less
-
Conventional rolling is a plastic deformation process that uses compression between two rolls to reduce material thickness and produce sheet/plane geometries. This deformation process modifies the material structure by generating texture, reducing the grain size, and strengthening the material. The rolling process can enhance the strength and hardness of lightweight materials while still preserving their inherent lightness. Lightweight metals like magnesium alloys tend to lack mechanical strength and hardness in load-bearing applications. The general rolling process is controlled by the thickness reduction, velocity of the rolls, and temperature. When held at a constant thickness reduction, each pass through the rolls introduces an increase in strain hardening, which could ultimately result in cracking, spallation, and other defects. This study is designed to optimize the rolling process by evaluating the effects of the strain rate, rather than the thickness reduction, as a process control parameter.more » « less
-
Olivine lattice preferred orientation (LPO), or texture, forms in relation to deformation mechanisms such as dislocation creep and can be observed in the upper mantle as seismic anisotropy. Olivine is also mechanically anisotropic, meaning that it responds to stresses differently depending on the direction of the stress. Understanding the interplay between anisotropic viscosity (AV) and LPO, and their role in deformation, is necessary for relating seismic anisotropy to mantle flow patterns. In this study, we employ three methods to predict olivine texture (D-Rex, MDM, and MDM+AV) in a shear box model and a subduction model. D-Rex and MDM are two representative texture development methods that have been compared before, and our results are in line with previous studies showing that textures computed by D-Rex develop faster and are stronger and more point-like than textures calculated with MDM. MDM+AV uses the same isotropic mantle stresses and particle paths as D-Rex and MDM but includes the effect of AV for texture predictions. MDM+AV predicts a texture similar to MDM with a distinct girdle-like orientation for simple shear deformation or at low strain in the subduction model. At larger strains, MDM+AV’s textures are more point-like and stronger compared to the other two methods. The effective viscosity for MDM+AV drops by up to 60% in a shear box model and can be either strengthened or weakened relative to isotropic viscosity for different regions of the subduction model experiencing different patterns of deformation. Our results emphasize the significant role of AV in olivine texture development, which could substantially affect geodynamic processes in the upper mantle.more » « less
-
Nanostructured steels are expected to have enhanced irradiation tolerance and improved strength. However, they suffer from poor microstructural stability at elevated temperatures. In this study, Fe–21Cr–5Al–0.026C (wt%) Kanthal D (KD) alloy belonging to a class of (FeCrAl) alloys considered for accident‐tolerant fuel cladding in light‐water reactors is nanostructured using two severe plastic deformation techniques of equal‐channel angular pressing (ECAP) and high‐pressure torsion (HPT), and their thermal stability between 500–700 °C is studied and compared. ECAP KD is found to be thermally stable up to 500 °C, whereas HPT KD is unstable at 500 °C. Microstructural characterization reveals that ECAP KD undergoes recovery at 550 °C and recrystallization above 600 °C, while HPT KD shows continuous grain growth after annealing above 500 °C. Enhanced thermal stability of ECAP KD is from significant fraction (>50%) of low‐angle grain boundaries (GBs) (misorientation angle 2–15°) stabilizing the microstructure due to their low mobility. Small grain sizes, a high fraction (>80%) of high‐angle GBs (misorientation angle >15°) and accordingly a large amount of stored GB energy, serve as the driving force for HPT KD to undergo grain growth instead of recrystallization driven by excess stored strain energy.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1016/j.actamat.2023.119395
