An official website of the United States government
Water droplet erosion (WDE) is a complex phenomenon that has been investigated for nearly a century. This form of erosion affects a wide range of energy industries from steam turbines and natural gas pipelines to wind turbine blades. The moving droplets impacting at a high relative speed create a high surge in surface pressure on the impacted material and damage the surface. The damage removes materials and can compromise strength for steam turbines and pipelines or affect the lift and drag forces on wind turbine blades. Research on WDE has been ongoing for decades with a majority of the reported results focused on metallic material testing and qualitative analysis comparing methodologies or surface conditions. The ongoing research at The University of Tulsa is conducting experiments with a variety of materials while exposed to an environment where water droplet erosion occurs. Impact velocity and droplet sizes are controlled within the facility and ongoing research with particle image velocimetry (PIV) is in use to characterize the falling droplets. Stainless steel 316, Aluminum 6061, and a variety of non-metallic materials are tested for a variety of conditions. The mass of each specimen is tracked and recorded at set intervals to determine the erosion ratio and erosion rate. Various other factors such as flowrate and rotational velocity are determined before testing as well as the percentage of droplets which impact the surface is determined with the use of a high-speed camera. Scanning electron microscopy (SEM) is also utilized to examine the material’s surfaces before and after testing to investigate the severity of erosion by water droplets. One impact velocity and one impact angle are set for all tested materials. These data points will be the starting point for future tests and modeling work to predict water droplet erosion based on simple factors.
more »
« less
PIV AND HIGH-SPEED IMAGING INVESTIGATION OF FALLING LIQUID DROPLET PROPERTIES
Liquid droplet impact is a subject that has been investigated in both engineering and non-engineering applications to understand and to control this phenomenon. Spray cooling, ink-jet printing, spray coating and painting, soil erosion prevention, pesticide application, and impact erosion are merely a few examples in which droplet impact is involved. Erosion caused by droplet impact on a solid surface is important in numerous elements of industrial equipment, such as pipelines, steam turbines, and wind turbine blades. Though experimental and modeling studies have been performed on this topic, most failed to perform quantitative investigation especially when it came to the erosion of wind turbine blades. Moreover, most approaches assume that the impacting droplets are completely spherical and unaffected by any local turbulence or vortex shedding. As the droplet erosion process could be affected by several parameters, such as the impact velocity, shape and size of the droplets, this study focuses on investigating droplet properties and movement in a controlled lab environment. High speed imaging and Particle Image Velocimetry (PIV) methods are used for this purpose. PIV is used to measure the velocity, circularity, and size of the falling droplets in both disturbed and un-disturbed flow conditions. High-speed camera imaging provides additional insight to the path of the droplets’ movement in the presence of any turbulence. Experiments are performed at a variety of flow rates utilizing a range of blunt needle gauge sizes to create different droplet sizes. It is observed that the blunt needles produce a train of droplets that are different in size following each leading droplet. This is a crucial observation as it will have a direct impact on the magnitude of erosion and should be considered in the future modeling efforts.
more »
« less
- Award ID(s):
- 1852477
- PAR ID:
- 10502265
- Publisher / Repository:
- ASME
- Date Published:
- Journal Name:
- Proceedings of the ASME 2024 Fluids Engineering Division Summer Meeting
- Subject(s) / Keyword(s):
- Particle image velocimetry liquid droplets high-speed imaging droplet properties
- Format(s):
- Medium: X
- Location:
- Anaheim, CA
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Quantification of the performance degradation on the annual energy production (AEP) of a wind farm due to leading‐edge (LE) erosion of wind turbine blades is important to design cost‐effective maintenance plans and timely blade retrofit. In this work, the effects of LE erosion on horizontal axis wind turbines are quantified using infrared (IR) thermographic imaging of turbine blades, as well as meteorological and SCADA data. The average AEP loss of turbines with LE erosion is estimated from SCADA and meteorological data to be between 3% and 8% of the expected power capture. The impact of LE erosion on the average power capture of the turbines is found to be higher at lower hub‐height wind speeds (peak around 50% of the turbine rated wind speed) and at lower turbulence intensity of the incoming wind associated with stable atmospheric conditions. The effect of LE erosion is investigated with IR thermography to identify the laminar to turbulent transition (LTT) position over the airfoils of the turbine blades. Reduction in the laminar flow region of about 85% and 87% on average in the suction and pressure sides, respectively, is observed for the airfoils of the investigated turbines with LE erosion. Using the observed LTT locations over the airfoils and the geometry of the blade, an average AEP loss of about 3.7% is calculated with blade element momentum simulations, which is found to be comparable with the magnitude of AEP loss estimated through the SCADA data.more » « less
-
Abstract This study focuses on the influence of the sea spray polydispersity on the vertical transport of momentum in a turbulent marine atmospheric boundary layer in high-wind conditions of a hurricane. The Eulerian multifluid model treating air and spray droplets of different sizes as interacting interpenetrating continua is developed and its numerical solutions are analyzed. Several droplet size distribution spectra and correlation laws relating wind speed and spray production intensity are considered. Polydisperse model solutions have confirmed the difference between the roles small and large spray droplets play in modifying the turbulent momentum transport that have been previously identified by monodisperse spray models. The obtained results have also provided a physical explanation for the previously unreported phenomenon of the formation of thin low-eddy-viscosity “sliding” layers in strongly turbulent boundary layer flows laden with predominantly fine spray. Significance StatementAchieving better accuracy in hurricane forecasts requires an in-depth understanding and accurate modeling of the ocean spray effect on the vertical fluxes of momentum and heat in a hurricane boundary layer. It has been shown that this effect depends on the size distribution of spray droplets, also known as spray polydispersity. This study aims to investigate the influence of a polydisperse spray on the vertical momentum transport within hurricane boundary layers by employing a modern theory of turbulent disperse multiphase flows.more » « less
-
Introduction:Agriculture is the largest user of water globally (i.e., 70% of freshwater use) and within the United States (i.e., 42% of freshwater use); irrigation ensures crops receive adequate water, thereby increasing crop yields. Surfactants have been used in various agricultural spray products to increase spray stability and alter droplet sizes. Methods:The effects of the addition of surfactant (0.1 wt% Surfactin; surface tension of 29.2 mN/m) to distilled water (72.79 mN/m) on spray dynamics and droplet formation were investigated in four flat fan (206.8–413.7 kPa), one full cone (137.9–413.7 kPa), and three LEPA bubbler (41.4–103.4 kPa) nozzles via imaging. Results and discussion:The flat fan and cone nozzles experienced second wind-induced breakup (i.e., unstable wavelengths drive breakup) of the liquid sheets exiting the nozzle; the addition of surfactant resulted in an increased breakup length and a decreased droplet size. The fan nozzles volumetric median droplet diameter decreased with the addition of surfactant (e.g., decreased by 26.3–65.6 μm in one nozzle). The full cone nozzle volumetric median droplet diameter decreased initially with the addition of surfactant (27.8, 14.3, and 13.4 μm at 137.9, 206.8, and 310.3 kPa respectively), but increased at 413.7 kPa (24.3 μm). Sprays from the bubbler nozzles were measured and observed to experience Rayleigh (i.e., the droplets form via capillary pinching at the end of the jet) and first wind-induced breakup (i.e., air impacts breakup along with capillary pinching). The effect of Surfactin on droplet size was minimal for the 41.4 kPa bubbler nozzle. The addition of surfactant increased the diameter of the jet or ligament formed from the bubbler plate, thereby increasing the breakup length and the droplet size at 68.9 and 103.4 kPa (droplet size increased by 750.6 and 4,462.7 μm, respectively).more » « less
-
Spray formed by a myriad of secondary droplets generated by the impact of raindrops on a deep-water pool is studied with a laboratory rain facility. Experiments are performed with two rain rates and raindrops fall on the water surface at a nearly constant velocity. The secondary droplets at various heights above the pool's water surface are recorded with a cinematic digital in-line holographic technique that consists of a high-speed camera, a pulsed Nd:YLF laser and associated optics. The experimental results show that in the heat-map scatter plots of radius versus velocity near the water surface of the pool, the droplets are distributed into three regions, corresponding to distinct physical mechanisms of droplet generation. It is found that the diameter distribution of the droplets in the rain field changes with height above the pool's water surfaces. Both numerical simulation and experimental data reveal that the liquid water content, due to the presence of secondary droplets, in the atmospheric surface layer decreases exponentially with increasing height.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Proceeding:
- The DOI is not currently available.
