skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


  • NSF Public Access
  • Search Results
  • In-situ monitoring of sintering and analytical modeling of densification and shrinkage in binder jetted 316L stainless steel
Title: In-situ monitoring of sintering and analytical modeling of densification and shrinkage in binder jetted 316L stainless steel
In binder jetting, shrinkage and deformation occur during the sintering step, both of which are affected by the green density of the binder jetted materials. The study innovatively introduces a cost-effective, practical, and in-process monitoring system for visualizing shrinkage and deformation on larger samples than conventionally observed using small-scale specimens in dillatometry equipment. The powder characteristics and binder jet printing process itself influence the initial green density. The comprehensive analysis of powder flowability and packing density, densification behavior, and shrinkage reveals that the consolidated parts using virgin powder (with a green density of 55%) can achieve a relative density above 99.9% with an anisotropic shrinkage in the Z>X>Y direction. In contrast, the used or recycled powder exhibits a lower green density of ∼48%, higher shrinkage rate in all three dimensions, and a decreased degree of anisotropy. Using in-process imaging and experimental data on the grain size attained through optical microscopy and electron backscatered diffraction imaging, the material's shear and bulk viscosities were determined. The formation of delta-ferrite and its impact on densification were discussed in the context of solid-state and supersolidus liquid phase sintering. The model relied on the continuum sintering theory formulated by Skorohod and Olevsky. The strain evolution from the in-situ imaging of sintering process is correlated with porosity based on the used feedstock and applied sintering temperatures. The outcomes of this study offer valuable perspectives on anisotropic sintering mechanisms, bridging the knowledge gap regarding the relationships between structures produced through binder jetting and subsequent sintering of materials.  more » « less
Award ID(s):
2050916
PAR ID:
10508628
Author(s) / Creator(s):
; ; ; ; ;
Publisher / Repository:
Elsevier
Date Published:
Journal Name:
Materialia
ISSN:
2589-1529
Page Range / eLocation ID:
102131
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; (, Journal of Manufacturing Science and Engineering)
    Abstract Binder jetting is an additive manufacturing process utilizing a liquid-based binding agent to selectively join the material in a powder bed. It is capable of manufacturing complex-shaped parts from a variety of materials including metals, ceramics, and polymers. This paper provides a comprehensive review on currently available reports on metal binder jetting from both academia and industry. Critical factors and their effects in metal binder jetting are reviewed and divided into two categories, namely material-related factors and process-related parameters. The reported data on density, dimensional and geometric accuracy, and mechanical properties achieved by metal binder jetting are summarized. With parameter optimization and a suitable sintering process, ten materials have been proven to achieve a relative density of higher than 90%. Indepth discussion is provided regarding densification as a function of various attributes of powder packing, printing, and post-processing. A few grades of stainless steel obtained equivalent or superior mechanical properties compared to cold working. Although binder jetting has gained its popularity in the past several years, it has not been sufficiently studied compared with other metal additive manufacturing (AM) processes such as powder bed fusion and directed energy deposition. Some aspects that need further research include the understanding of powder spreading process, binder-powder interaction, and part shrinkage. 
    more » « less
  2. ; ; ; (, The International Journal of Advanced Manufacturing Technology)
    Binder jetting is a powder bed additive manufacturing process where an object is created by depositing liquid binder onto the surface of powder, selectively binding particles in each layer. The quality of the as-printed parts is influenced not only by process parameters such as layer thickness, binder saturation, print speed, and drying time but also by the location within the build box. This study highlights the location-dependent nature of green density and dimensional accuracy in the as-printed samples, and the observed trends are thoroughly discussed. A conventional powder spreading using a single roller was compared with a double roller to maximize powder packing and bed uniformity prior to binder jetting process. The significance of these observations lies in their impact on densification behavior, shrinkage, and the final geometry of the printed part. 
    more » « less
  3. (, Proceedings of the ASME 2019 International Manufacturing Science and Engineering Conference (MSEC2019))
    The objective of this study is to compare three different feedstock powders for the binder jetting process by characterizing their flowability and sinterability. Binder jetting additive manufacturing is a promising technology for fabricating ceramic parts with complex or customized geometries. Granulation is a promising material preparation method due to the potential high sinterability and flowability of the produced powder. However, no study has been made to systematically compare raw and granulated powders in terms of their flowing and sintering behaviors. This paper aims at filling this knowledge gap. Two raw powders (i.e., fine raw powder of 300 nm and coarse raw powder of 70 μm) and one granulated powder from spray freeze drying were compared. Different flowability metrics, including volumetric flow rate, mass flow rate, Hausner ratio, Carr index, and repose angle were measured. Different sinterability metrics, including sintered bulk density, volume shrinkage, and densification ratio were compared for all three powders. Results show that granulated powder achieved comparably high flowability to that of the coarse raw powder and also comparably high sinterability to that of the fine raw powder. Moreover, suitable metrics for the characterization of the sinterability and flowability for these three powders are recommended. This study suggests spray freeze drying produces high-quality feedstock powder for binder jetting process. 
    more » « less
  4. ; ; ; ; ; (, Powder Metallurgy)
    In the binder jetting (BJ) process, as in most of powder bed additive manufacturing technologies, the powder is periodically recoated onto the substrate layer-by-layer. The elements of the current deposited layer corresponding to the part being manufactured are bonded together using a polymeric binder. In all cases that require a thermal process for sintering, the internal structure of the finished part is defined by the internal structure of the powder bed. This article focuses on the discrete element modelling (DEM) of various powder spreading methods during recoating and their impact on the powder bed structure particularly applied to binder jetting technology. The article demonstrates that despite the thinness of the deposited layers, they typically exhibit porosity and particle and pore size non-uniformities along the build-up direction. These irregularities contribute to the anisotropic sintering shrinkage observed in green BJ bodies during experiments. However, the experiments presented confirmed by modelling show that without binder deposition, the powder bed – except for a narrow surface layer – remains relatively uniform, regardless of the recoating method used. It is the binder injection into the porous structure of the powder bed that disrupts this homogeneity, locks in large surface pores, and exacerbates the effects of powder segregation during spreading. Finally, several strategies, explored via simulation, are proposed to reduce porosity variations during BJ: using a combined roller-wide blade method for powder spreading and a two-hopper approach, where each layer consists of small particles deposited over larger ones. 
    more » « less
  5. ; ; ; (, Journal of Manufacturing Science and Engineering)
    Abstract This technical brief reports an experimental investigation on the effect of feed region density on resultant sintered density and intermediate densities (powder bed density and green density) during the binder jetting additive manufacturing process. The feed region density was increased through compaction. The powder bed density and green density were determined by measuring the mass and dimension. The sintered density was measured with the Archimedes’ method. As the relative feed region density increased from 44% to 65%, the powder bed density increased by 5.7%, green density by 8.5%, and finally sintered density by 4.5%. Statistical testing showed that these effects were significant. This study showed that compacting the powder in the feed region is an effective method to alter the density of parts made via binder jetting additive manufacturing. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email