An official website of the United States government
Purpose This paper aims to study the mass loss of three-dimensional (3D) printed materials at high temperatures. A preconcentration and analysis technique, static headspace gas chromatography-mass spectrometry (SHS-GC-MS), is demonstrated for the analysis of volatile compounds liberated from fused deposition modeling (FDM) and stereolithography (SLA) 3D printed models under elevated temperatures. Design/methodology/approach A total of seven commercial 3D printing materials were tested using the SHS-GC-MS approach. The printed model mass and mass loss were examined as a function of FDM printing parameters including printcore temperature, model size and printing speed, and the use of SLA postprocessing procedures. A high temperature resin was used to demonstrate that thermal degradation products can be identified when the model is incubated under high temperatures. Findings At higher printing temperatures and larger model sizes, the initial printed model mass increased and showed more significant mass loss after thermal incubation for FDM models. For models produced by SLA, the implementation of a postprocessing procedure reduced the mass loss at elevated temperatures. All FDM models showed severe structural deformation when exposed to high temperatures, while SLA models remained structurally intact. Mass spectra and chromatographic retention times acquired from the high temperature resin facilitated identification of eight compounds (monomers, crosslinkers and several photoinitiators) liberated from the resin. Originality/value The study exploits the high sensitivity of SHS-GC-MS to identify thermal degradation products emitted from 3D printed models under elevated temperatures. The results will aid in choosing appropriate filament/resin materials and printing mechanisms for applications that require elevated temperatures.
more »
« less
3D printed models are an accurate, cost-effective, and reproducible tool for quantifying terrestrial thermal environments
Predicting ecological responses to rapid environmental change has become one of the greatest challenges of modern biology. One of the major hurdles in forecasting these responses is accurately quantifying the thermal environments that organisms experience. The distribution of temperatures available within an organism's habitat is typically measured using data loggers called operative temperature models (OTMs) that are designed to mimic certain properties of heat exchange in the focal organism. The gold standard for OTM construction in studies of terrestrial ectotherms has been the use of copper electroforming which creates anatomically accurate models that equilibrate quickly to ambient thermal conditions. However, electroformed models require the use of caustic chemicals, are often brittle, and their production is expensive and time intensive. This has resulted in many researchers resorting to the use of simplified OTMs that can yield substantial measurement errors. 3D printing offers the prospect of robust, easily replicated, morphologically accurate, and cost-effective OTMs that capture the benefits but alleviate the problems associated with electroforming. Here, we validate the use of OTMs that were 3D printed using several materials across eight lizard species of different body sizes and living in habitats ranging from deserts to tropical forests. We show that 3D printed OTMs have low thermal inertia and predict the live animal's equilibration temperature with high accuracy across a wide range of body sizes and microhabitats. Finally, we developed a free online repository and database of 3D scans (https://www.3dotm.org/) to increase the accessibility of this tool to researchers around the world and facilitate ease of production of 3D printed models. 3D printing of OTMs is generalizable to taxa beyond lizards. If widely adopted, this approach promises greater accuracy and reproducibility in studies of terrestrial thermal ecology and should lead to improved forecasts of the biological impacts of climate change.
more »
« less
- PAR ID:
- 10510093
- Publisher / Repository:
- Elsevier
- Date Published:
- Journal Name:
- Journal of Thermal Biology
- Volume:
- 119
- Issue:
- C
- ISSN:
- 0306-4565
- Page Range / eLocation ID:
- 103762
- Subject(s) / Keyword(s):
- 3D printing Biophysical model Climate change OTM Open database Operative temperature model Thermal physiology Thermoregulation
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Construction 3D Printing (C3DP) with sulfur concrete holds great potential for sustainable construction on Earth and beyond. However, a key challenge is optimizing the thermal C3DP process to minimize layer deformations while enhancing interlayer adhesion for improved mechanical strength. To tackle this challenge, this paper presents a physics-based model of heat transfer within a 3D-printed sulfur concrete structure. Numerical implementations of the model are proposed for 3D and 2D structures in Cartesian coordinates. Upon calibration, the model estimates the spatiotemporal distribution of the temperature within the structure based on thermal properties, printing parameters, and environmental conditions. The model is calibrated using experimental data, where the effect of printing parameters is analyzed, and is then utilized to simulate multiple terrestrial and Martian construction scenarios. It identifies a range of printing speeds and interlayer delays that optimize extrudate properties, while also enabling automated control of the thermal C3DP process for optimal performance.more » « less
-
null (Ed.)Purpose This paper aims to summarize the up-to-date research performed on combinations of various biofibers and resin systems used in different three-dimensional (3D) printing technologies, including powder-based, material extrusion, solid-sheet and liquid-based systems. Detailed information about each process, including materials used and process design, are described, with the resultant products’ mechanical properties compared with those of 3D-printed parts produced from pure resin or different material combinations. In most processes introduced in this paper, biofibers are beneficial in improving the mechanical properties of 3D-printed parts and the biodegradability of the parts made using these green materials is also greatly improved. However, research on 3D printing of biofiber-reinforced composites is still far from complete, and there are still many further studies and research areas that could be explored in the future. Design/methodology/approach The paper starts with an overview of the current scenario of the composite manufacturing industry and then the problems of advanced composite materials are pointed out, followed by an introduction of biocomposites. The main body of the paper covers literature reviews of recently emerged 3D printing technologies that were applied to biofiber-reinforced composite materials. This part is classified into subsections based on the form of the starting materials used in the 3D printing process. A comprehensive conclusion is drawn at the end of the paper summarizing the findings by the authors. Findings Most of the biofiber-reinforced 3D-printed products exhibited improved mechanical properties than products printed using pure resin, indicating that biofibers are good replacements for synthetic ones. However, synthetic fibers are far from being completely replaced by biofibers due to several of their disadvantages including higher moisture absorbance, lower thermal stability and mechanical properties. Many studies are being performed to solve these problems, yet there are still some 3D printing technologies in which research concerning biofiber-reinforced composite parts is quite limited. This paper unveils potential research directions that would further develop 3D printing in a sustainable manner. Originality/value This paper is a summary of attempts to use biofibers as reinforcements together with different resin systems as the starting material for 3D printing processes, and most of the currently available 3D printing techniques are included herein. All of these attempts are solutions to some principal problems with current 3D printing processes such as the limit in the variety of materials and the poor mechanical performance of 3D printed parts. Various types of biofibers are involved in these studies. This paper unveils potential research directions that would further widen the use of biofibers in 3D printing in a sustainable manner.more » « less
-
Advances in vat photopolymerization 3D printing have the potential to significantly improve the production of ceramic materials for electrochemical energy devices. Solid oxide fuel cells (SOFCs) and solid oxide electrolysis cells (SOECs) necessitate high‐resolution ceramic manufacturing methods, as well as precisely controlled porosity (≈20–40%) for optimal gas transport. Achieving a balance between this porosity and mechanical integrity, especially under thermal stress, remains a challenge. Herein, the successful fabrication of porous yttria‐stabilized zirconia (YSZ) ceramics using vat photopolymerization 3D printing is demonstrated, achieving porosities ranging from 6% to 40% and corresponding grain sizes of ≈80–550 nm. It is found that 3D‐printed YSZ with ≈33% porosity exhibited a Weibull modulus ofm = 5.3 and a characteristic strength of over 36 MPa. In the investigation, it is further revealed that these ceramics can withstand thermal shock up to 500 °C, retaining over 70% of their flexural strength. This remarkable performance suggests significant potential for 3D‐printed porous YSZ in SOFCs and SOECs, paving the way for potential improved efficiency, reduced fabrication costs, and innovative designs in these next‐generation clean energy technologies.more » « less
-
Abstract The macro-porous ceramics has promising durability and thermal insulation performances. A cost-effective and scalable additive manufacturing technique for the fabrication of macro-porous ceramics, with a facile approach to control the printed porosity is reported in the paper. Several ceramic inks were prepared, the foaming agent was used to generate gaseous bubbles in the ink, followed by the direct ink writing and the ambient-pressure and room-temperature drying to create the three-dimensional geometries. The experimental studies were performed to optimize the printing quality. A set of studies revealed the optimal printing process parameters for printing the foamed ceramic ink with a high spatial resolution and fine surface quality. Varying the concentration of the foaming agent enabled the controllability of the structural porosity. The maximum porosity can reach 85%, with a crack-free internal porous structure. The tensile tests showed that the printed macro-porous ceramics have enhanced durability with the addition of fiber. With a high-fidelity 3D printing process and precise control of the porosity, the printed samples exhibited a low thermal conductivity and high mechanical strength.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1016/j.jtherbio.2023.103762
