skip to main content


This content will become publicly available on December 31, 2025

Title: 17-4 PH and SS316L bimetallic structures via additive manufacturing
Balancing strength and ductility is crucial for structural materials, yet often presents a paradoxical challenge. This research focuses on crafting a unique bimetallic structure, combining non-magnetic, stainless steel 316L (SS316L) with limited strength but enhanced ductility and magnetic, martensitic 17-4 PH with higher strength but lower ductility. Utilizing a powder-based laser-directed energy deposition (L-DED) system, two vertical bimetallic configurations (SS316L/17-4 PH) and a radial bimetallic structure (SS316L core encased in 17-4 PH) were fabricated. Monolithic SS316L, 17-4 PH, and a 50% SS316L/50% 17-4 PH mixture were printed. The printed samples' phase, microstructure, room temperature mechanical properties, and fracture morphology were examined in as-printed conditions. Bimetallic samples exhibited both phases, with a smooth grain transition at the interface. Radial bimetallic samples demonstrated higher mechanical strength than other compositions, except 17-4 PH. These findings showcase the potential of the L-DED approach for creating functional components with tailored mechanical properties.  more » « less
Award ID(s):
1934230
NSF-PAR ID:
10536681
Author(s) / Creator(s):
;
Publisher / Repository:
Taylor and Francis
Date Published:
Journal Name:
Virtual and Physical Prototyping
Volume:
19
Issue:
1
ISSN:
1745-2759
Subject(s) / Keyword(s):
Stainless steel 316L (SS316L) 17-4PH laser-directed energy deposition (L-DED) Additive manufacturing (AM) 3D Printing.
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Stainless steel 316L (SS316L) is widely used in fracture management devices. However, SS316L does not offer any bacterial infection resistance and can cause metal-ion sensitivity due to Ni-ions' presence. 17-4PH can emerge as a promising substitute due to the intrinsic antibacterial properties of copper, a 75% reduction in nickel content, and superior mechanical properties. SS316L and 17-4 PH were manufactured using laser-directed energy deposition (LDED). 17-4PH specimens surpassed the compressive strength of SS316L by over 150%. A static magnetic field was generated in 17-4 PH specimens to understand in vitro bone cell-material interactions. In vitro human fetal osteoblast cell culture and bacterial inhibition study using Staphylococcus aureus and Pseudomonas aeruginosa were carried out on these specimens with SS316L as control and as-processed and magnetized 17-4 PH as treatments. Results demonstrated that magnetized 17-4 PH exhibited 25% enhancement in hFOB proliferation and 70% reduction in bacterial colonization compared to SS316L. 
    more » « less
  2. Abstract

    The feasibility of using argon‐atomized QT 17‐4+ stainless steel powder for directed energy deposition (DED) additive manufacturing is studied. The QT 17‐4+ steel is a novel martensitic steel designed based on the compositional modification of the standard 17‐4 precipitation‐hardened (PH) stainless steel. This modification aims to achieve better mechanical properties of as‐deposited components compared to the heat‐treated wrought 17‐4PH steel. In this study, QT 17‐4+ steel powder is used for DED, for the first time. The influence of laser power, laser scan speed, powder feed rate, and hatch overlap on the density is studied. The central composite design is used to determine the experimental matrix of these factors. The response surface methodology is used to obtain the empirical statistical prediction model. Both columnar and equiaxed parent austenite grain structures are observed. X‐ray diffraction analyses reveal a decrease in the percentage of retained austenite from 19% in the powder to 5% after DED. The microhardness of the DED processed sample in the as‐deposited state is slightly higher than that of wrought 17‐4PH steel either solution‐annealed or H900‐aged. A higher 0.2% yield strength, a lower ultimate tensile strength, and lower elongation are observed for the vertically printed test sample, when compared to the horizontal one.

     
    more » « less
  3. IMECE2022-88299 Midwest Engineered Systems Inc. has created a novel laser wire metal deposition process, ADDere manufacturing. ADDere has a much higher deposition rate than powder bed fusion, making it ideal for large components. In this project, the mechanical properties of ADDere printed materials were tested and compared to typical values found in ASM publications to show the quality of materials manufactured by the ADDere printing process. A detailed material analysis was performed on samples made from Ti-6Al-4V and 17-4 PH stainless steel. This work builds upon an earlier study of samples made from 17-4 PH that were produced using a single direction pattern. In this project, the 17-4 PH samples were printed in a cross hatched pattern, and testing results were compared to existing data from single direction samples of the previous research. The Ti-6Al-4V samples were created in two builds. One using the uni-directional method and the other with the crossed pattern. Testing specimens were removed from the samples using a water jet cutter and further machined into ASTM tensile bars and metallurgic mounts to perform a thorough material evaluation. The Ti-6Al-4V sample met the expected values in the ASM literature, and the cross hatched 17-4 PH exhibited a higher hardness and better microstructure than the single direction samples from the previous work. It was also observed that when the Ti64 samples were manufactured in the cross hatched pattern, the properties indicated slight improvement and more homogeneity than those printed in single layer direction. The obtained results indicate that ADDere’s printing process can produce highly refined materials that are customizable with their expected uses. This work showcases an excellent industry collaboration of an undergraduate research experience. 
    more » « less
  4. Abstract

    Critical‐sized defects remain a significant challenge in orthopaedics. 3D printed scaffolds are a promising treatment but are still limited due to inconsistent osseous integration. The goal of the study is to understand how changing the surface roughness of 3D printed titanium either by surface treatment or artificially printing rough topography impacts the mechanical and biological properties of 3D printed titanium. Titanium tensile samples and discs were printed via laser powder bed fusion. Roughness was manipulated by post‐processing printed samples or by directly printing rough features. Experimental groups in order of increasing surface roughness were Polished, Blasted, As Built, Sprouts, and Rough Sprouts. Tensile behavior of samples showed reduced strength with increasing surface roughness. MC3T3 pre‐osteoblasts were seeded on discs and analyzed for cellular proliferation, differentiation, and matrix deposition at 0, 2, and 4 weeks. Printing roughness diminished mechanical properties such as tensile strength and ductility without clear benefit to cell growth. Roughness features were printed on mesoscale, unlike samples in literature in which roughness on microscale demonstrated an increase in cell activity. The data suggest that printing artificial roughness on titanium scaffold is not an effective strategy to promote osseous integration.

     
    more » « less
  5. Wire arc additive manufacturing (WAAM) presents a highly promising alternative to conventional subtractive manufacturing methods to produce metallic components, particularly in the aerospace industry, where there is a demand for 17–4 precipitation-hardened (PH) stainless steel structures. This study focuses on investigating the microstructural characteristics, showing microhardness evaluations, and analyzing the tensile properties of the as-printed parts during the 17–4 PH manufacturing process at different locations and directions. The fabrication is carried out using gas metal wire arc additive manufacturing (GM-WAAM). As a result, it was found that the microstructure of the as-deposited part showed a complex configuration consisting of both finely equiaxed and coarsely formed δ-ferrite phases with vermicular and lathy morphologies. These phases were dispersed inside the martensitic matrix, while a small amount of retained austenite was also present. It was observed that the volume fraction of retained austenite (20–5%) and δ-ferrite phases (15.5–2.5%) decreased gradually from the bottom to the top of the as-deposited wall. This reduction in the fractions of these phases resulted in a progressive increase in both hardness (∼37%) and ultimate tensile strength (UTS) along the building direction. This study successfully fabricates a high-strength and ductile 17–4 PH as-printed part using WAAM. The findings provide evidence supporting the feasibility of employing WAAM for producing defect-free, high-strength components on a large scale while maintaining mechanical properties similar or better than wrought alloy 17–4 PH. 
    more » « less