An official website of the United States government
Large-scale multi-directional real-time hybrid simulations (RTHS) are used to assess the maximum considered earthquake (MCE) seismic performance of a 40-story steel building equipped with supplemental nonlinear viscous dampers. These dampers are placed between outrigger trusses and the perimeter columns of a building that was part of the inventory for the California Tall Building Initiative (TBI) PEER study. The analytical substructure for the RTHS consists of a 3-D nonlinear model of the building while the experimental substructure consists of a full scale nonlinear viscous damper. Other dampers in the structure are analytically modelled using an online explicit model updating scheme where the physical damper is used to obtain the parameters of the analytical damper models during the RTHS. The displacement, residual drift, and ductility demand are found to be reduced by adding the dampers to the outrigger, but only in the direction of the plane of the outriggers. Higher modes, including torsional modes, contribute to the 3-D seismic response.
more »
« less
REAL TIME HYBRID SIMULATION (RTHS) OF A 2-STORY BUILDING EQUIPPED WITH NOVEL BASE ISOLATION SYSTEMS
A new friction device using band brake technology, termed the Banded Rotary Friction Damper (BRFD), has been fabricated at the NHERI Lehigh Experimental Facility. The damping mechanism is based on band brake technology and leverages a self-energizing mechanism to produce large damping forces with low input energy. The device is a second-generation BRFD, where the friction mechanism is achieved using two electric actuators. The BRFD generates a damping force as a function of the input force provided by the electric actuators, where the ratio of BRFD force output-to-electric actuator force input is equal to about 112. The paper presents the results of a study using real-time hybrid simulations (RTHS) to investigate the performance of the BRFD’s in mitigating seismic hazards of a two-story reinforced concrete building. The building has two and three special moment resisting frames (SMRFs) in the east-west and north-south directions, respectively. In order to perform the RTHS, the north south SMRF is considered and the BRFD along with a parallel elastic member is used as a base isolation system to mitigate the effects of earthquake hazards by reducing story drift and floor accelerations of the structure. For the RTHS the building and the elastic component of the isolator are part of the analytical substructure while the experimental substructure is comprised of the BRFD. The response of the structure is investigated involving six Maximum Considered Earthquake (MCE) hazard level events that includes three near-field and three far-field ground motions. The explicit, unconditionally stable dissipative Modified KR-α integration algorithm is used to accurately integrate the equations of motion during the RTHS. The model for the reinforced concrete building is created using explicit non-linear force-based fiber elements to discretely model each member of the structure. First, the details of the prototype of the BRFD are presented. Second, the details of the isolator system consisting of a linear spring element and the BRFD are discussed. Finally, the details of the RTHS study and the results are presented. The building’s inter-story peak and residual story drift from base-isolated and fixed-based conditions are compared. Results show that the proposed isolator system produces a significant reduction in both maximum inter-story drift and residual drift, and reduces the damage developed in the structure during the MCE.
more »
« less
- Award ID(s):
- 2037771
- PAR ID:
- 10562140
- Publisher / Repository:
- WCEE2024
- Date Published:
- Journal Name:
- World Conference on Earthquake Engineering proceedings
- ISSN:
- 3006-5933
- ISBN:
- 978-1-119-61942-0
- Format(s):
- Medium: X
- Location:
- Milan, Italy
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Real-time hybrid simulation (RTHS) divides a structural system into analytical and experimental substructures that are coupled through their common degrees of freedom. This paper introduces a framework to enable RTHS to be performed on 3D nonlinear models of tall buildings with rate dependent nonlinear response modification devices, where the structure is subjected to multi-directional wind and earthquake natural hazards. A 40-story tall building prototype with damped outriggers is selected as a case study. The analytical substructure for the RTHS consists of a 3-D nonlinear model of the structure, where each member in the building is discretely modeled in conjunction with the use of a super element. The experimental substructure for the RTHS consists of a full-scale rate-dependent nonlinear viscous damper that is physically tested in the lab, with the remaining dampers in the outrigger system modeled analytically. The analytically modeled dampers use a stable explicit non-iterative element with an online model updating algorithm, by which the covariance matrix of the damper model’s state variables does not become ill-conditioned. The damper model parameters can thereby be updated in real-time using measured data from the experimental substructure. The explicit MKR-α method is optimized and used in conjunction with the super element to efficiently integrate the condensed equations of motion of a large complex model having more than 1000 nonlinear elements, thus enabling multi-axis earthquake and wind hybrid nonlinear simulations to be performed in real-time. An adaptive servo-hydraulic actuator control scheme is used to enable precise real-time actuator displacements in the experimental substructure to be achieved that match the target displacements during a RTHS. The IT real-time architecture for integrating the components of the framework is described. To assess the framework, 3D RTHS of the 40-story structure were performed involving multi-axis translational and torsional response to multi-directional earthquake and wind natural hazards. The RTHS technique was applied to perform half-power tests to experimentally determine the amount of supplemental damping provided by the damped outrigger system for translational and torsional modes of vibration of the building. The results from the study presented herein demonstrate that RTHS can be applied to large nonlinear large structural systems involving multi-axis response to multi-directional excitation.more » « less
-
null (Ed.)Floor isolation systems (FISs) are used to mitigate earthquake-induced damage to sensitive building contents and equipment. Traditionally, the isolated floor and the primary building structure (PS) are analyzed independently, assuming the PS response is uncoupled from the FIS response. Dynamic coupling may be non-negligible when nonlinearities are present under large deflections at strong disturbance levels. This study investigates a multi-functional FIS that functions primarily as an isolator (i.e., attenuating total acceleration sustained by the isolated equipment) at low-to-moderate disturbance levels, and then passively adapt under strong disturbances to function as a nonlinear (vibro-impact) dynamic vibration absorbers to protect the PS (i.e., reducing inter-story drifts). The FIS, therefore, functions as a dual-model vibration isolator/absorber system, with displacement dependent response adaptation. A scale experimental model—consisting of a three-story frame and an isolated mass—is used to demonstrate and evaluate the design methodology via shake table tests. The properties of the 3D-printed rolling pendulum (RP) bearing, the seismic gap, and the impact mechanism are optimized to achieve the desired dual-mode performance. A suite of four ground motions with varying spectral qualities are used, and their amplitudes are scaled to represent various hazards—from service level earthquake (SLE), to design basis earthquake (DBE), and even maximum considered earthquake (MCE). The performance of the multi-functional FIS is established and is described in this paper.more » « less
-
This paper investigates the effects of near-fault pulse-type ground motions on the structural response of a 3-story steel structure with nonlinear viscous dampers using the real-time hybrid simulation (RTHS) testing method. The real time loop of action and reaction between the experimental and numerical partitions executed in the RTHS enabled the accurate capturing of the velocity pulse effects of pulse-type ground motions. An ensemble of 10 natural pulse-type ground motions at the design basis earthquake (DBE) level is used for the RTHS. The accuracy of RTHS under high velocity loading is demonstrated, and thereby, is a validated method for experimentally investigation of the complicated structural behavior of structures with rate-dependent damping devices. The test results showed that the dampers are essentially effective in earthquake hazard mitigation effects involving pulse-type ground motions. The average peak story drift ratio under the set of pulse-type ground motions is 1.08% radians with a COV value less than 0.3, which indicates that the investigated structure would achieve the ASCE 7-10 seismic performance objective for Occupancy Category III structures under the DBE level pulse-type ground motions.more » « less
-
Abstract Real‐time hybrid simulation (RTHS) involves dividing a structural system into numerical and experimental substructures. The experimental substructure is challenging to model analytically and is therefore modeled physically in the laboratory. Analytical substructures are conventionally modeled using the finite element method. The two substructures are kinematically linked, and the governing equations of motion are solved in real‐time. Thus, the state determination of the analytical substructure needs to occur within the timestep, which is of the order of a few milliseconds. All structural systems are supported by a soil‐foundation system and any evaluation of the efficacy of response modification devices placed in the structure should consider soil‐foundation structure interaction (SFSI) effects. SFSI adds compliance to a structural system, thereby altering the natural frequencies. Additionally, nonlinear behavior in the soil can result in residual deformations in the foundation and structure, as well as provide added damping. These effects can occur under both wind and earthquake loading. To overcome the barrier of the large computational effort required to model SFSI effects in real‐time using the conventional finite element approach, a neural network (NN) model is combined with an explicit‐based analytical substructure and experimental substructure with dampers to create a framework for performing RTHS with SFSI effects. The framework includes a block of long‐short term memory (LSTM) layers that is combined with a parallel rectified linear unit (ReLU) to form a NN model of the soil‐foundation system. RTHS of a tall 40‐story steel building equipped with nonlinear viscous dampers and subjected to a windstorm are performed to illustrate the framework. It was found that a number of factors have an effect on the quality of RTHS results. These include: (i) the discretization of the wind loading into bins of basic wind speed; (ii) the extent of the NN model training as determined by the root mean square error (RMSE); (iii) noise in the restoring forces produced by the NN model and its interaction with the integration algorithm; and, (iv) the bounding of outliers of the NN model's output. Guidelines for extending the framework for the RTHS of structures subjected to seismic loading are provided.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Proceeding:
- The DOI is not currently available.
