Search for: All records

Abstract This study presented the use of SrTiO₃/Y₂O₃nanoparticles for the reinforcement of dental poly(methyl methacrylate) (PMMA) to enhance its mechanical properties important for everyday use of denture base materials. The average crystallite size of prepared nanoparticles was 19.9 nm. The influence of 0.5, 1.0, and 1.5 wt% SrTiO₃/Y₂O₃loading on absorbed impact energy, microhardness and tensile properties was investigated. Scanning electron microscopy of the composite fracture surface revealed multiple toughening mechanisms, with agglomerates directly included in the crack pinning, indicating improvement in mechanical performance. Dynamic mechanical analysis proved that agglomerates improved the elastic behavior of PMMA and confirmed the absence of a residual monomer. After the incorporation of SrTiO₃/Y₂O₃, the mechanical properties of composites showed a high increase compared to neat PMMA. The optimal concentration of nanoparticles was 1 wt%, for which the microhardness, modulus of elasticity, and absorbed impact energy were higher by 218.4%, 65.8% and 135.6%, respectively. With such a high increase, this research showed that SrTiO₃/Y₂O₃represents an efficient filler which use does not have to be limited to dental materials. HighlightsSrTiO₃/Y₂O₃hybrid nanoparticles were prepared.PMMA‐SrTiO₃/Y₂O₃composite showed increase in impact resistance up to 135.4%.Elastic behavior of PMMA was improved.With 1 wt% of SrTiO₃/Y₂O₃, microhardness increased by 218.4%. 

Abstract Bioactive degradable scaffolds that facilitate bone healing while fighting off initial bacterial infection have the potential to change established strategies of dealing with traumatic bone injuries. To achieve this a composite material made from calcium phosphate graphene (CaPG), and MXene was synthesized. CaPG was created by functionalizing graphene oxide with phosphate groups in the presence of CaBr with a Lewis acid catalyst. Through this transformation, Ca²⁺and PO₄³⁻inducerons are released as the material degrades thereby aiding in the process of osteogenesis. The 2D MXene sheets, which have shown to have antibacterial properties, were made by etching the Al from a layered Ti₃AlC₂(MAX phase) using HF. The hot‐pressed scaffolds made of these materials were designed to combat the possibility of infection during initial surgery and failure of osteogenesis to occur. These two failure modes account for a large percentage of issues that can arise during the treatment of traumatic bone injuries. These scaffolds were able to retain induceron‐eluting properties in various weight percentages and bring about osteogenesis with CaPG alone and 2 wt% MXene scaffolds demonstrating increased osteogenic activity as compared to no treatment. Additionally, added MXene provided antibacterial properties that could be seen at as little as 2 wt%. This CaPG and MXene composite provides a possible avenue for developing osteogenic, antibacterial materials for treating bone injuries. 

Abstract Ceramic/polymer composites can be chemically stable, mechanically strong, and flexible, which make them candidates for electric devices, such as pressure or temperature sensors, energy storage or harvesting devices, actuators, and so forth. Depending on the application, various electrical properties are of importance. Polymers usually have low dielectric permittivity, but increased dielectric permittivity can be achieved by the addition of the ceramic fillers with high dielectric constant. With the aim to enhance dielectric properties of the composite without loss of flexibility, 5 wt% of BaTiO₃‐Fe₂O₃powder was added into a polyvinylidene fluoride matrix. The powder was prepared by different synthesis conditions to produce core/shell structures. The effect of the phase composition and morphology of the BaTiO₃‐Fe₂O₃core/shell filler on the structure and lattice dynamics of the polymer composites was investigated. Based on the results of the thermal analysis, various parameters of ceramic/polymer composites were determined. Differences in the phase composition and morphology of the filler have an influence on the formation of various polyvinylidene fluoride allomorphs and the degree of crystallinity. Furthermore, the dielectric performances of pure polyvinylidene fluoride and the polymer/ceramic composites were measured. 

Abstract The field of photovoltaics is revolutionized in recent years by the development of two–dimensional (2D) type‐II heterostructures. These heterostructures are made up of two different materials with different electronic properties, which allows for the capture of a broader spectrum of solar energy than traditional photovoltaic devices. In this study, the potential of vanadium (V)‐doped WS₂is investigated, hereafter labeled V‐WS₂, in combination with air‐stable Bi₂O₂Se for use in high‐performance photovoltaic devices. Various techniques are used to confirm the charge transfer of these heterostructures, including photoluminescence (PL) and Raman spectroscopy, along with Kelvin probe force microscopy (KPFM). The results show that the PL is quenched by 40%, 95%, and 97% for WS₂/Bi₂O₂Se, 0.4 at.% V‐WS₂/Bi₂O₂Se, and 2 at.% V‐WS₂/Bi₂O₂Se, respectively, indicating a superior charge transfer in V‐WS₂/Bi₂O₂Se compared to pristine WS₂/Bi₂O₂Se. The exciton binding energies for WS₂/Bi₂O₂Se, 0.4 at.% V‐WS₂/Bi₂O₂Se and 2 at.% V‐WS₂/Bi₂O₂Se heterostructures are estimated to be ≈130, 100, and 80 meV, respectively, which is much lower than that for monolayer WS₂. These findings confirm that by incorporating V‐doped WS₂, charge transfer in WS₂/Bi₂O₂Se heterostructures can be tuned, providing a novel light‐harvesting technique for the development of the next generation of photovoltaic devices based on V‐doped transition metal dichalcogenides (TMDCs)/Bi₂O₂Se. 

This review provides an overview of the fabrication methods for Ti3C2Tx MXene-based hybrid photocatalysts and evaluates their role in degrading organic dye pollutants. Ti3C2Tx MXene has emerged as a promising material for hybrid photocatalysts due to its high metallic conductivity, excellent hydrophilicity, strong molecular adsorption, and efficient charge transfer. These properties facilitate faster charge separation and minimize electron–hole recombination, leading to exceptional photodegradation performance, long-term stability, and significant attention in dye degradation applications. Ti3C2Tx MXene-based hybrid photocatalysts significantly improve dye degradation efficiency, as evidenced by higher percentage degradation and reduced degradation time compared to conventional semiconducting materials. This review also highlights computational techniques employed to assess and enhance the performance of Ti3C2Tx MXene-based hybrid photocatalysts for dye degradation. It identifies the challenges associated with Ti3C2Tx MXene-based hybrid photocatalyst research and proposes potential solutions, outlining future research directions to address these obstacles effectively. 

This study investigates the synergistic properties of 2D/1D ReS2-decorated LaFeO3 nanohybrids, presenting a unique approach to photocatalytic dye degradation. Through facile hydrothermal synthesis, we fabricated these nanohybrids with varying ReS2 loadings. Notably, the 5 wt% ReS2-LaFeO3 nanohybrid exhibited highly efficient visible-light-driven photocatalytic degradation of Congo red (CR) dye, achieving 82% degradation within 180 min. This enhanced performance can be attributed to synergistic effects arising from the unique 2D/1D architecture and the modified charge-transfer properties within the 2D/1D ReS2-LaFeO3 heterostructure. These findings demonstrate the potential of these multifunctional nanohybrids for applications in environmental remediation.