An official website of the United States government
Impacting drops are ubiquitous and the corresponding impact force is their most studied dynamic quantity. However, impact forces arising from collisions with curved surfaces are understudied. In this study, we impact small cups with falling drops across drop Reynolds number 2975–12 800, isolating five dominant parameters influencing impact force: drop height and diameter, surface curvature and wettability, and impact eccentricity. These parameters are effectively continuous in their domain and have stochastic variability. The unpredictable dynamics of the system incentivize the implementation of tools that can unearth relationships between parameters and make predictions about impact force for parameter values for which there is not explicit experimental data. We predict force due to the impacting drop in a concave target using an ensemble learning algorithm comprised of four base algorithms: a random forest regressor, k-nearest neighbor, a gradient boosting regressor, and a multi-layer perceptron. We train and test our algorithm with original experimental data comprising 387 total trials using four cup radii with two wetting conditions each. Our approach permits the determination of relative importance of the input features in producing impact force and force predictions which can be compared to scaling relations modified from those for flat targets. Algorithmic predictions indicate that deformation of the drop and surface wettability, often neglected in scaling for impact force on flat surfaces, are important for concave targets. Finally, our approach provides another opportunity for the application of machine learning to characterize complex systems' fluid mechanics for which experimental variables are numerous and vary independently.
more »
« less
Predictive modelling of drop ejection from damped, dampened wings by machine learning
The high frequency, low amplitude wing motion that mosquitoes employ to dry their wings inspires the study of drop release from millimetric, forced cantilevers. Our mimicking system, a 10-mm polytetrafluoroethylene cantilever driven through ±1 mm base amplitude at 85 Hz, displaces drops via three principal ejection modes: normal-to-cantilever ejection, sliding and pinch-off. The selection of system variables such as cantilever stiffness, drop location, drop size and wetting properties modulates the appearance of a particular ejection mode. However, the large number of system features complicate the prediction of modal occurrence, and the transition between complete and partial liquid removal. In this study, we build two predictive models based on ensemble learning that predict the ejection mode, a classification problem, and minimum inertial force required to eject a drop from the cantilever, a regression problem. For ejection mode prediction, we achieve an accuracy of 85% using a bagging classifier. For inertial force prediction, the lowest root mean squared error achieved is 0.037 using an ensemble learning regression model. Results also show that ejection time and cantilever wetting properties are the dominant features for predicting both ejection mode and the minimum inertial force required to eject a drop.
more »
« less
- PAR ID:
- 10204034
- Date Published:
- Journal Name:
- Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Volume:
- 476
- Issue:
- 2241
- ISSN:
- 1364-5021
- Page Range / eLocation ID:
- 20200467
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
During solid surface impact, a falling drop's energy is transformed into oscillations of its liquid/gas interface. We consider drop deposition during oblique impact in the capillary-ballistic regime characterized by high Reynolds number and moderate Weber number. We treat this as an inverse problem showing that post-impact observations of the frequency spectrum and modal partition of energy allow one to determine a drop's pre-impact characteristics and wetting properties. Our analysis is useful for quantifying contact-line dissipation during inertial spreading and can be used as a diagnostic technique for determining substrate wetting properties.more » « less
-
There is considerable interest in measuring, with nanoscale spatial resolution, the physical properties of lipid membranes because of their role in the physiology of living systems. Due to its ability to nondestructively image surfaces in solution, tapping mode atomic force microscopy (TMAFM) has proven to be a useful technique for imaging lipid membranes. However, further information concerning the mechanical properties of surfaces is contained within the time-resolved tip/sample force interactions. The tapping forces can be recovered by taking the second derivative of the cantilever deflection signal and scaling by the effective mass of the cantilever; this technique is referred to as scanning probe acceleration microscopy. Herein, we describe how the maximum and minimum tapping forces change with surface mechanical properties. Furthermore, we demonstrate how these changes can be used to measure mechanical changes in lipid membranes containing cholesterol.more » « less
-
Abstract The dynamic properties of freestanding rock towers are important inputs for seismic stability and vibration hazard assessments, however data describing the natural frequencies, mode shapes, and damping ratios of these landforms remain rare. We measured the ambient vibration of 14 sandstone and conglomerate rock towers and fins in Utah, United States, using broadband seismometers and nodal geophones. Fundamental frequencies vary between 0.8 and 15 Hz—inversely with tower height—and generally exhibit subhorizontal modal vectors oriented parallel to the minimum tower width. Modal damping ratios are low across all features, between 0.6% and 2.2%. We reproduced measured modal attributes in 3D numerical eigenfrequency models for 10 of the 14 landforms, showing that the fundamental mode of these features is full-height bending akin to a cantilever. Fin-like landforms commonly have a torsional second mode whereas tower-like features have a second full-height bending mode subperpendicular to the fundamental. In line with beam theory predictions, our data confirm that fundamental frequencies scale with the ratio of a tower’s width to its squared height. Compiled data from 18 other sites support our results, and taken together, provide guidance for estimating the modal properties of rock towers required for vibration risk assessment and paleoseismic shaking intensity analysis in different settings.more » « less
-
This paper presents the mixing, trapping, and ejection of a single microparticle based on an acoustic tweezers. Finite Element Model (FEM) simulation, along with analytical modeling, is used to study the selectivity of particles based on size and material properties. The acoustic tweezers is optimized to have a single trapping zone, where particles are trapped due to acoustic radiation force (which is calculated for particle sizes exceeding the Rayleigh approximation). The tweezers is experimentally shown to lift microparticles from the tweezers surface, selectively trap a single particle based on size and material acoustic properties, and then eject it upwards for collection. All these are obtained with negligible heat generation.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1098/rspa.2020.0467
