An official website of the United States government
Silicon carbide (SiC) MOSFET features low switching loss and it is advantageous in high switching frequency application, but the manufacture per Ampere cost is approximately five times higher than the silicon (Si) IGBT. Therefore, by paralleling Si IGBT and SiC MOSFET together, a trade-off between cost and loss is achieved. In this paper, a four control freedoms active gate driver (AGD) including turn-on delay, turn-off delay, and two independent gate voltages, is proposed to optimize the performance of the paralleled device. By adjusting these four control freedoms, optimal operation for paralleled device can be obtained. Moreover, the proposed AGD can dynamically adjust the current ratio between two paralleled devices, which can help achieve thermal balance between two devices and improve system reliability. Double pulse test (DPT) experimental results are presented and analyzed to validate the effectiveness of the proposed AGD for paralleled Si IGBT and SiC MOSFET application.
more »
« less
Application of An Active Gate Driver for Paralleling Operation of Si IGBT and SiC MOSFET
Wide band gap (WBG) devices feature high switching frequency operation and low switching loss. They have been widely adopted in tremendous applications. Nevertheless, the manufacture cost for SiC MOSFET greater than that of the Si IGBT. To achieve a trade off between cost and efficiency, the hybrid switch, which includes the paralleling operation of Si IGBT and SiC MOSFET, is proposed. In this article, an active gate driver is used for the hybrid switch to optimize both the switching and thermal performances. The turn-on and turn-off delays between two individual switches are controlled to minimize the switching loss of traditional Si IGBT. In this way, a higher switching frequency operation can be achieved for the hybrid switch to improve the converter power density. On the other hand, the gate source voltages are adjusted to achieve an optimized thermal performance between two individual switches, which can improve the reliability of the hybrid switch. The proposed active gate driver for hybrid switch is validated with a 2 kW Boost converter.
more »
« less
- Award ID(s):
- 1939144
- PAR ID:
- 10317577
- Date Published:
- Journal Name:
- IEEE 12th Energy Conversion Congress Exposition - Asia
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract—Wide band gap (WBG) devices, like silicon carbide (SiC) MOSFET has gradually replaced the traditional silicon counterpart due to their advantages of high operating temperature and fast switching speed. Paralleling operations of SiC MOSFETs are unavoidable in high power applications in order to meet the system current requirement. However, parasitics mismatches among different paralleling devices would cause current unbalance issues, which would reduce the system reliability and maximum current capability. Thus, to achieve current balancing operation, this paper proposes a solution of using multi-level active gate driver, where the dynamic current sharing during turn-on and turn-off processes are achieved by adjusting the delays, intermediate turn-on and turn-off voltages. The static current sharing is maintained by regulating the static turn-on gate voltage, where the on-state resistance mismatch between different devices can be compensated. A double pulse test setup with two different SiC MOSFETs is built to emulate the scenario of worst case application with large differences of threshold voltage and on-state resistance. The experimental results demonstrate that the proposed active gate driver can achieve both dynamic and static current sharing operations for SiC MOSFETs with paralleling operation. Moreover, the system control diagram is discussed. Simulation studies are conducted to achieve closed-loop control of the paralleled SiC MOSFETs with the aid of the active gate driver approach.more » « less
-
Multilevel modular resonant switched-capacitor converter can achieve either zero-current switching (ZCS) or zero-voltage switching (ZVS) by utilizing different converter control strategies. This paper presents a comprehensive way to compare the root mean square (RMS) value of current flowing through switching devices in both ZCS operation and ZVS operation. The study shows that with appropriate converter parameter design, the ZVS operation allows the RMS value of switch current at most 10% lower than that in ZCS operation. Therefore, the converter operating at ZVS mode has the potential to achieve higher efficiency comparing to the converter that operates at ZCS mode due to less semiconductor conduction loss. Furthermore, the ZVS operation can reduce the power loss due to MOSFET output capacitance. A 6x converter with 54V input voltage, 9V output voltage and 600W power rating is used as an example to show the detailed design procedure. Simulation results are provided to verify the theoretical analysis. Also, a 600W lab prototype that has 6 to 1 voltage conversion ratio has been built to verify the theoretical analysis.more » « less
-
Wide band gap (WBG) devices have been widely adopted in numerous industrial applications. In medium voltage applications, multi-level converters are necessary to reduce the voltage stress on power devices, which increases the system control complexity and reduces power density and reliability. High voltage silicon carbide (SiC) MOSFET enables the medium voltage applications with less voltage level, simple control strategy and high power density. Nevertheless, great challenges have been posed on the gate driver design for high voltage SiC MOSFET. Wireless power transfer (WPT) can achieve power conversion with large airgap, which can satisfy the system isolation requirement. Thus, in this article, a WPT based gate driver is designed for the medium voltage SiC MOSFET. The coil is optimized by considering voltage isolation, coupling capacitance, size, and efficiency. Experimental prototype was built and tested to validate the effectiveness of the proposed WPT based gate driver.more » « less
-
This paper investigates the use of power semiconductor devices in a nine - level cascaded H-bridge (CHB) multilevel inverter topology with an integrated battery energy storage system (BESS) for a 13.8kV medium voltage distribution system. In this topology, the bulky conventional step-up 60 Hz transformer is not used. The purpose of this study is to analyze the use of SiC MOSFET and Si IGBT devices in the inverter system to evaluate their respective performances. SiC MOSFET and Si IGBT switching devices are modeled and characterized using Saber® modeling software. The switching losses, thermal performance, and efficiency of the inverter system are investigated, and measurements are obtained from the simulation. Saber® provides a good capability for characterizing semiconductor models in the real world, with great features of computation. A three-phase SiC power MOSFET-based multilevel CHB inverter prototype is presented for experimental verification. In the investigation, better performances of SiC MOSFET devices are recorded. SiC devices demonstrate promising performance at different switching frequency and temperature ranges.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- https://doi.org/10.1109/ECCE-Asia49820.2021.9479254
