- Award ID(s):
- 2002741
- NSF-PAR ID:
- 10520949
- Publisher / Repository:
- American Chemical Society
- Date Published:
- Journal Name:
- ACS Nano
- Volume:
- 17
- Issue:
- 20
- ISSN:
- 1936-0851
- Page Range / eLocation ID:
- 20353 to 20365
- Subject(s) / Keyword(s):
- metal contact, transition metal dichalcogenides, Fermi level pinning, interface chemistry, band alignment, imperfections, density functional theory
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
The high contact resistance of transition metal dichalcogenide (TMD) -based devices is receiving considerable attention due to its limitation on electronic performance. The mechanism of Fermi level (EF) pinning, which causes the high contact resistance, is not thoroughly understood to date. In this study, the metal (Ni and Ag)/Mo-TMDs surfaces and interfaces are characterized by X-ray photoelectron spectroscopy, atomic force microscopy, scanning tunneling microscopy and spectroscopy, and density functional theory systematically. Ni and Ag form covalent and van der Waals (vdW) interfaces on Mo-TMDs, respectively. Imperfections are detected on Mo-TMDs, which leads to electronic and spatial variations. Gap states appear after the adsorption of single, and two metal atoms on Mo-TMDs. The combination of the interface reaction type (covalent or vdW), the imperfection variability of the TMD materials, and the gap states induced by contact metals with different weights are concluded to be the origins of EF pinning.more » « less
-
Contact engineering on monolayer layer (ML) semiconducting transition metal dichalcogenides (TMDs) is considered the most challenging problem towards using these materials as a transistor channel in future advanced technology nodes. The typically observed strong Femi level pinning induced in part by the reaction of the source/drain contact metal and the ML TMD frequently results in a large Schottky barrier height, which limits the electrical performance of ML TMD field-effect transistors (FETs). However, at a microscopic level, little is known about how interface defects or reaction sites impact the electrical performance of ML TMD FETs. In this work, we have performed statistically meaningful electrical measurements on at least 120 FETs combined with careful surface analysis to unveil contact resistance dependencies on the interface chemistry. In particular, we achieved a low contact resistance for ML MoS2 FETs with ultra-high vacuum (UHV, 3×10-11 mbar) deposited Ni contacts, ~500 ohm·μm, which is 5 times lower than the contact resistance achieved when deposited at high vacuum (HV, 3×10-6 mbar) conditions. These electrical results strongly correlate with our surface analysis observations. X-ray photoelectron spectroscopy (XPS) revealed significant bonding species between Ni and MoS2 under UHV conditions compared to HV. We also studied the Bi/MoS2 interface under UHV and HV deposition conditions. Different from the case of Ni, we do not observe a difference in contact resistance or interface chemistry between contacts deposited under UHV and HV. Finally, this article also explores the thermal stability and reliability of the two contact metals employed here.more » « less
-
Abstract Semiconducting transition metal dichalcogenides (TMDs) are promising for flexible high-specific-power photovoltaics due to their ultrahigh optical absorption coefficients, desirable band gaps and self-passivated surfaces. However, challenges such as Fermi-level pinning at the metal contact–TMD interface and the inapplicability of traditional doping schemes have prevented most TMD solar cells from exceeding 2% power conversion efficiency (PCE). In addition, fabrication on flexible substrates tends to contaminate or damage TMD interfaces, further reducing performance. Here, we address these fundamental issues by employing: (1) transparent graphene contacts to mitigate Fermi-level pinning, (2) MoO
x capping for doping, passivation and anti-reflection, and (3) a clean, non-damaging direct transfer method to realize devices on lightweight flexible polyimide substrates. These lead to record PCE of 5.1% and record specific power of 4.4 W g−1for flexible TMD (WSe2) solar cells, the latter on par with prevailing thin-film solar technologies cadmium telluride, copper indium gallium selenide, amorphous silicon and III-Vs. We further project that TMD solar cells could achieve specific power up to 46 W g−1, creating unprecedented opportunities in a broad range of industries from aerospace to wearable and implantable electronics. -
Two-dimensional semiconductors such as transition metal dichalcogenides (TMDs) are making impressive strides in a short duration compared to other candidates. However, to unlock their full potential for advanced logic transistors, attention must be given to improving the contacts or interfaces they form. One approach is to interface with a suitable low work function metal contact to allow the surface Fermi level (EF) movement toward intended directions, thereby augmenting the overall electrical performance. In this work, we implement physical characterization to understand the tin (Sn) contact interface on monolayer and bulk molybdenum disulfide (MoS2) via in situ x-ray photoelectron spectroscopy and ex situ atomic force microscopy. A Sn contact exhibited a van der Waals type weak interaction with the MoS2 bulk surface where no reaction between Sn and MoS2 is detected. In contrast, reaction products with Sn—S bonding are detected with a monolayer surface consistent with a covalentlike interface. Band alignment at the interface indicates that Sn deposition induces n-type properties in the bulk substrate, while EF of the monolayer remains pinned. In addition, the thermal stability of Sn on the same substrates is investigated in a sequential ultrahigh vacuum annealing treatment at 100, 200, 300, and 400 °C. Sn sublimated/desorbed from both substrates with increasing temperature, which is more prominent on the bulk substrate after annealing at 400 °C. Additionally, Sn significantly reduced the monolayer substrate and produced detectable interface reaction products at higher annealing temperatures. The findings can be strategized to resolve challenges with contact resistance that the device community is having with TMDs.
-
Atomically thin two-dimensional transition-metal dichalcogenides (2D-TMDs) have emerged as semiconductors for next-generation nanoelectronics. As 2D-TMD-based devices typically utilize metals as the contacts, it is crucial to understand the properties of the 2D-TMD/metal interface, including the characteristics of the Schottky barriers formed at the semiconductor-metal junction. Conventional methods for investigating the Schottky barrier height (SBH) at these interfaces predominantly rely on contact-based electrical measurements with complex gating structures. In this study, we introduce an all-optical approach for non-contact measurement of the SBH, utilizing high-quality WS2/Au heterostructures as a model system. Our approach employs a below-bandgap pump to excite hot carriers from the gold into WS2 with varying thicknesses. By monitoring the resultant carrier density changes within the WS2 layers with a broadband probe, we traced the dynamics and magnitude of charge transfer across the interface. A systematic sweep of the pump wavelength enables us to determine the SBH values and unveil an inverse relationship between the SBH and the thickness of the WS2 layers. First-principles calculations reveal the correlation between the probability of injection and the density of states near the conduction band minimum of WS2. The versatile optical methodology for probing TMD/metal interfaces can shed light on the intricate charge transfer characteristics within various 2D heterostructures, facilitating the development of more efficient and scalable nano-electronic and optoelectronic technologies.more » « less