skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.


Title: Femtosecond 3D photolithography through a digital micromirror device and a microlens array
Based on the microscale 3D point cloud projection with a digital micromirror device (DMD) and a microlens array (MLA) developed recently, we explore the capabilities of this specific type of 3D projection in 3D lithography with femtosecond light in this study. Unlike 3D point cloud projection with UV continuous light demonstrated before, high accuracy positioning between the DMD and the MLA is required to have rays simultaneously arrive at the designed voxel positions to induce two-photon absorption with femtosecond light. Because of this additional requirement, a new positioning method through direct microscope inspection of the relative positions of the DMD and the MLA is developed in this study. Because of the usage of a rectangular MLA, around four rays can arrive at each projecting voxel at the same time. Thus, to the best of our knowledge, a new algorithm for determining the pixel map on the DMD to the 3D point cloud projection with a femtosecond laser is also developed. It is observed that a very long exposure time is required to generate 3D patterns with the new 3D projection scheme because of the very limited number of rays used for projecting each voxel with the new algorithm. It is also found that 3D structures with desired shapes should be projected far away from the MLA ( ∼<#comment/> 15 f to 30 f , with f being the focal distance of the MLA) in the 3D lithography with this femtosecond 3D point cloud projection. For patterns projected closer than 10 f , shapes are distorted because of unwanted voxels cured with the 3D projection technique using a DMD and MLA.  more » « less
Award ID(s):
1826078
PAR ID:
10531271
Author(s) / Creator(s):
; ;
Publisher / Repository:
Optical Society of America
Date Published:
Journal Name:
Applied Optics
Volume:
61
Issue:
16
ISSN:
1559-128X; APOPAI
Format(s):
Medium: X Size: Article No. 4891
Size(s):
Article No. 4891
Sponsoring Org:
National Science Foundation
More Like this
  1. Flat lenses enable thinner, lighter, and simpler imaging systems. However, large-area and high-NA flat lenses have been elusive due to computational and fabrication challenges. Here we applied inverse design to create a multi-level diffractive lens (MDL) with thickness <<#comment/> 1 . 35 µ<#comment/> m , diameter of 4.13 mm, and N A = 0.9 at wavelength of 850 nm (bandwidth ∼<#comment/> 35 n m ). Since the MDL is created in polymer, it can be cost-effectively replicated via imprint lithography. 
    more » « less
  2. We perform single-shot frequency domain holography to measure the ultrafast spatio-temporal phase change induced by the optical Kerr effect and plasma in flexible Corning Willow Glass during femtosecond laser–matter interactions. We measure the nonlinear index of refraction ( n 2 ) to be ( 3.6 ±<#comment/> 0.1 ) ×<#comment/> 10 −<#comment/> 16 c m 2 / W and visualize the plasma formation and recombination on femtosecond time scales in a single shot. To compare with the experiment, we carry out numerical simulations by solving the nonlinear envelope equation. 
    more » « less
  3. Amorphous tantala ( T a 2 O 5 ) thin films were deposited by reactive ion beam sputtering with simultaneous low energy assist A r + or A r + / O 2 + bombardment. Under the conditions of the experiment, the as-deposited thin films are amorphous and stoichiometric. The refractive index and optical band gap of thin films remain unchanged by ion bombardment. Around 20% improvement in room temperature mechanical loss and 60% decrease in absorption loss are found in samples bombarded with 100-eV A r + . A detrimental influence from low energy O 2 + bombardment on absorption loss and mechanical loss is observed. Low energy A r + bombardment removes excess oxygen point defects, while O 2 + bombardment introduces defects into the tantala films. 
    more » « less
  4. The mid-IR spectroscopic properties of E r 3 + doped low-phonon C s C d C l 3 and C s P b C l 3 crystals grown by the Bridgman technique have been investigated. Using optical excitations at ∼<#comment/> 800 n m and ∼<#comment/> 660 n m , both crystals exhibited IR emissions at ∼<#comment/> 1.55 , ∼<#comment/> 2.75 , ∼<#comment/> 3.5 , and ∼<#comment/> 4.5 µ<#comment/> m at room temperature. The mid-IR emission at 4.5 µm, originating from the 4 I 9 / 2 →<#comment/> 4 I 11 / 2 transition, showed a long emission lifetime of ∼<#comment/> 11.6 m s for E r 3 + doped C s C d C l 3 , whereas E r 3 + doped C s P b C l 3 exhibited a shorter lifetime of ∼<#comment/> 1.8 m s . The measured emission lifetimes of the 4 I 9 / 2 state were nearly independent of the temperature, indicating a negligibly small nonradiative decay rate through multiphonon relaxation, as predicted by the energy-gap law for low-maximum-phonon energy hosts. The room temperature stimulated emission cross sections for the 4 I 9 / 2 →<#comment/> 4 I 11 / 2 transition in E r 3 + doped C s C d C l 3 and C s P b C l 3 were determined to be ∼<#comment/> 0.14 ×<#comment/> 10 −<#comment/> 20 c m 2 and ∼<#comment/> 0.41 ×<#comment/> 10 −<#comment/> 20 c m 2 , respectively. The results of Judd–Ofelt analysis are presented and discussed. 
    more » « less
  5. The measurement and stabilization of the carrier–envelope offset frequency f C E O via self-referencing is paramount for optical frequency comb generation, which has revolutionized precision frequency metrology, spectroscopy, and optical clocks. Over the past decade, the development of chip-scale platforms has enabled compact integrated waveguides for supercontinuum generation. However, there is a critical need for an on-chip self-referencing system that is adaptive to different pump wavelengths, requires low pulse energy, and does not require complicated processing. Here, we demonstrate efficient f C E O stabilization of a modelocked laser with only 107 pJ of pulse energy via self-referencing in an integrated lithium niobate waveguide. We realize an f - 2 f interferometer through second-harmonic generation and subsequent supercontinuum generation in a single dispersion-engineered waveguide with a stabilization performance equivalent to a conventional off-chip module. The f C E O beatnote is measured over a pump wavelength range of 70 nm. We theoretically investigate our system using a single nonlinear envelope equation with contributions from both second- and third-order nonlinearities. Our modeling reveals rich ultrabroadband nonlinear dynamics and confirms that the initial second-harmonic generation followed by supercontinuum generation with the remaining pump is responsible for the generation of a strong f C E O signal as compared to a traditional f - 2 f interferometer. Our technology provides a highly simplified system that is robust, low in cost, and adaptable for precision metrology for use outside a research laboratory. 
    more » « less