skip to main content

Explore Research Products in the NSF-PAR

  • NSF Public Access
  • Search Results
  • A Sparse Representation Classification Approach for Near Real-Time, Physics-Based Functional Monitoring of Aerosol Jet-Fabricated Electronics
Title: A Sparse Representation Classification Approach for Near Real-Time, Physics-Based Functional Monitoring of Aerosol Jet-Fabricated Electronics
Abstract Aerosol jet printing (AJP) is a direct-write additive manufacturing (AM) method, emerging as the process of choice for the fabrication of a broad spectrum of electronics, such as sensors, transistors, and optoelectronic devices. However, AJP is a highly complex process, prone to intrinsic gradual drifts. Consequently, real-time process monitoring and control in AJP is a bourgeoning need. The goal of this work is to establish an integrated, smart platform for in situ and real-time monitoring of the functional properties of AJ-printed electronics. In pursuit of this goal, the objective is to forward a multiple-input, single-output (MISO) intelligent learning model—based on sparse representation classification (SRC)—to estimate the functional properties (e.g., resistance) in situ as well as in real-time. The aim is to classify the resistance of printed electronic traces (lines) as a function of AJP process parameters and the trace morphology characteristics (e.g., line width, thickness, and cross-sectional area (CSA)). To realize this objective, line morphology is captured using a series of images, acquired: (i) in situ via an integrated high-resolution imaging system and (ii) in real-time via the AJP standard process monitor camera. Utilizing image processing algorithms developed in-house, a wide range of 2D and 3D morphology features are extracted, constituting the primary source of data for the training, validation, and testing of the SRC model. The four-point probe method (also known as Kelvin sensing) is used to measure the resistance of the deposited traces and as a result, to define a priori class labels. The results of this study exhibited that using the presented approach, the resistance (and potentially, other functional properties) of printed electronics can be estimated both in situ and in real-time with an accuracy of ≥ 90%.  more » « less
Award ID(s):
1752069
NSF-PAR ID:
10188888
Author(s) / Creator(s):
 ; ; ; ; ;
Date Published:
Journal Name:
Journal of Manufacturing Science and Engineering
Volume:
142
Issue:
8
ISSN:
1087-1357
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; ( , Journal of Micro and Nano-Manufacturing)
    null (Ed.)
    Abstract Aerosol jet printing (AJP) is a direct-write additive manufacturing technique, which has emerged as a high-resolution method for the fabrication of a broad spectrum of electronic devices. Despite the advantages and critical applications of AJP in the printed-electronics industry, AJP process is intrinsically unstable, complex, and prone to unexpected gradual drifts, which adversely affect the morphology and consequently the functional performance of a printed electronic device. Therefore, in situ process monitoring and control in AJP is an inevitable need. In this respect, in addition to experimental characterization of the AJP process, physical models would be required to explain the underlying aerodynamic phenomena in AJP. The goal of this research work is to establish a physics-based computational platform for prediction of aerosol flow regimes and ultimately, physics-driven control of the AJP process. In pursuit of this goal, the objective is to forward a three-dimensional (3D) compressible, turbulent, multiphase computational fluid dynamics (CFD) model to investigate the aerodynamics behind: (i) aerosol generation, (ii) aerosol transport, and (iii) aerosol deposition on a moving free surface in the AJP process. The complex geometries of the deposition head as well as the pneumatic atomizer were modeled in the ansys-fluent environment, based on patented designs in addition to accurate measurements, obtained from 3D X-ray micro-computed tomography (μ-CT) imaging. The entire volume of the constructed geometries was subsequently meshed using a mixture of smooth and soft quadrilateral elements, with consideration of layers of inflation to obtain an accurate solution near the walls. A combined approach, based on the density-based and pressure-based Navier–Stokes formation, was adopted to obtain steady-state solutions and to bring the conservation imbalances below a specified linearization tolerance (i.e., 10−6). Turbulence was modeled using the realizable k-ε viscous model with scalable wall functions. A coupled two-phase flow model was, in addition, set up to track a large number of injected particles. The boundary conditions of the CFD model were defined based on experimental sensor data, recorded from the AJP control system. The accuracy of the model was validated using a factorial experiment, composed of AJ-deposition of a silver nanoparticle ink on a polyimide substrate. The outcomes of this study pave the way for the implementation of physics-driven in situ monitoring and control of AJP. 
    more » « less
  2. ; ; ; ; ; ( , Additive Manufacturing Letters)
    The reliability of additively manufactured flexible electronics or so-called printed electronics is defined as mean time to failure under service conditions, which often involve mechanical loads. It is thus important to understand the mechanical behavior of the printed materials under such conditions to ensure their applicational reliability in, for example, sensors, biomedical devices, battery and storage, and flexible hybrid electronics. In this article, a testing protocol to examine the print quality of additively nanomanufactured electronics is presented. The print quality is assessed by both tensile and electrical resistivity responses during in-situ tension tests. A laser based additive nanomanufacturing method is used to print conductive silver lines on polyimide substrates, which is then tested in-situ under tension inside a scanning electron microscope (SEM). The surface morphology of the printed lines is continuously monitored via the SEM until failure. In addition, the real-time electrical resistance variations of the printed silver lines are measured in-situ with a multimeter during tensile tests conducted outside of the SEM. The protocol is shown to be effective in assessing print quality and aiding process tuning. Finally, it is revealed that samples appearing identical under the SEM can have significant different tendencies to delaminate. 
    more » « less
  3. ; ( , Advanced Materials Technologies)
    Abstract

    The generation of electronic waste (e‐waste) poses a significant environmental challenge, necessitating strategies to extend electronics’ lifespan and incorporate eco‐friendly materials to enable their rapid degradation after disposal. Foldable electronics utilizing eco‐friendly materials offer enhanced durability during operation and degradability at the end of their life cycle. However, ensuring robust physical adhesion between electrodes/circuits and substrates during the folding process remains a challenge, leading to interface delamination and electronic failure. In this study, electrohydrodynamic (EHD) printing is employed as a cost‐effective method to fabricate the eco‐friendly foldable electronics by printing PEDOT:PSS/graphene composite circuits onto polyvinyl alcohol (PVA) films. The morphology and electrical properties of the printed patterns using inks with varying graphene and PEDOT:PSS weight ratios under different printing conditions are investigated. The foldability of the printed electronics is demonstrated, showing minimal resistance variation and stable electronic response even after four folds (16 layers) and hundreds of folding and unfolding cycles. Additionally, the application of printed PEDOT:PSS/graphene circuit is presented as a resistive temperature sensor for monitoring body temperature and respiration behavior. Furthermore, the transient features and degradation of the PEDOT:PSS/graphene/PVA based foldable electronics are explored, highlighting the potential promise as transient electronics in reducing electronic waste.

     
    more » « less
  4. ; ; ; ; ; ; ; ( , Journal of Intelligent Manufacturing)
    Abstract

    In droplet-on-demand liquid metal jetting (DoD-LMJ) additive manufacturing, complex physical interactions govern the droplet characteristics, such as size, velocity, and shape. These droplet characteristics, in turn, determine the functional quality of the printed parts. Hence, to ensure repeatable and reliable part quality it is necessary to monitor and control the droplet characteristics. Existing approaches for in-situ monitoring of droplet behavior in DoD-LMJ rely on high-speed imaging sensors. The resulting high volume of droplet images acquired is computationally demanding to analyze and hinders real-time control of the process. To overcome this challenge, the objective of this work is to use time series data acquired from an in-process millimeter-wave sensor for predicting the size, velocity, and shape characteristics of droplets in DoD-LMJ process. As opposed to high-speed imaging, this sensor produces data-efficient time series signatures that allows rapid, real-time process monitoring. We devise machine learning models that use the millimeter-wave sensor data to predict the droplet characteristics. Specifically, we developed multilayer perceptron-based non-linear autoregressive models to predict the size and velocity of droplets. Likewise, a supervised machine learning model was trained to classify the droplet shape using the frequency spectrum information contained in the millimeter-wave sensor signatures. High-speed imaging data served as ground truth for model training and validation. These models captured the droplet characteristics with a statistical fidelity exceeding 90%, and vastly outperformed conventional statistical modeling approaches. Thus, this work achieves a practically viable sensing approach for real-time quality monitoring of the DoD-LMJ process, in lieu of the existing data-intensive image-based techniques.

     
    more » « less
  5. ; ; ( , Advanced Materials Technologies)
    Abstract

    Additive manufacturing (AM) is rapidly revolutionizing modern manufacturing with recent progress in advanced printing methods and improved properties of printed materials. However, traditional AM methods are limited by their input‐oriented nature, which demands tedious trial‐and‐error tuning of printing parameters to achieve desired output properties. Here, an output‐oriented artificial intelligence‐integrated AM (AIAM) method is reported that enables an user to specify desired output properties while the printer autonomously discovers the optimal input printing parameters by integrating hybrid machine learning models and in situ measurements. Based on a predictive mapping between the input printing parameters and the output properties of interests established with <20 experiments designed by active learning, inverse design tasks are performed to intelligently generate the printing parameter settings that lead to desired outcomes using reinforcement learning. This method is demonstrated by autonomous aerosol jet printing (AJP) of conductive polymer films and achieving user‐defined electrical resistances with an ultralow error of 3.7%. The AIAM method, with its output‐oriented nature, holds the potential to significantly improve the autonomy, predictability, efficiency, and accessibility of the AM processes, which will unlock new possibilities in the autonomous and intelligent printing of a broad range of functional materials and devices.

     
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email